Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for LamasaTech Versi Indoor Digital Signage Totem
Summary of Contents for LamasaTech Versi Indoor Digital Signage Totem
- Page 1 Versi Indoor Digital Signage Totem Installation Manual www.lamasatech.com...
- Page 2 Table of Contents Package Contents Tools Required Instructions Troubleshooting...
-
Page 3: Package Contents
Package Contents... - Page 4 Contents For each Versi Totem you have ordered you will have 5 boxes. The boxes will contain the following contents*. Security Covers (2)** Remote Control WiFi Aerial Poster Wall Frame Versi Power Display Cable Screws Mounting Rails ICE power Brackets for cable splitter display Side arms for...
- Page 5 Glass back cover if you have ordered a single-sided totem, or second display if you have ordered a double-sided display. Choice of base You will have one of the bases below, depending on your order. Large base Slim base...
-
Page 6: Tools Required
Tools Required... -
Page 7: Phillips Screwdriver
Tools Required Tools that may be required during your installation. Phillips Screwdriver Socket Set (optional) - Page 8 Instructions...
- Page 9 Instructions Remove the covers from the arms by unscrewing the cap found at the top and bottom. Removing the Caps shown on each covers Screw in the arms to the base at the bottom (shown by the arrows below). There will be 4 screws in total on either side...
- Page 10 In your prepared space, you will bolt the base to the ground using the anchor bolts. There are 6 bolts in total.
- Page 11 Install the crossmembers, do not tighten all screws until they are all in place. There will be 4 screws on each side per crossmember. Screw the bottom arms to the lower half of the kiosk, there will be a total of 6 screws per side.
- Page 12 Thread the power cable along the arms. Starting from the bottom and work your way to the top. You will find a hole near the top to feed the power cable through. This will allow you to plug this into the display. If you require an ethernet cable, this will be easier to thread through the opposite arm.
- Page 13 Lay the display on a soft flat surface ensuring the screen is protected. Screw brackets into the back of the screen, this must be done on the two long side of the screen. Please use the outer holes of the bracket, as indicated by the green boxes below.
- Page 14 Install the screen into the kiosk frame by using the mount and hook method, lift the screen into the frame and hook to the metal mounts on either side (There are 2 on each side, indicated by the green circles below). Secure the frame to the screen by screwing in on the sides.
- Page 15 If you have a double-sided totem, repeat the previous steps to install the second screen. Or, if you have a single-sided totem, you can now install the glass back cover following the step below. Lay the glass black cover on a soft flat surface, screw in the brackets to the back of the cover and install the cover to the opposite side of the screen by using the mount and hook method as previously used.
- Page 16 Replace the covers at the top of the arms and ensure the cover that has the space for the threaded cable, is at the bottom. Finally, screw in the WiFi Antenna at the top. If you have two screens there will be two antennas to screw in.
- Page 17 If you have purchased the camera bar with your kiosk you will be now install this at the top. First you will need to install the securing screws at the top of the kiosk. Be sure not to fully screw them in. You will then place the camera bar holes into the screws and slide along and secure the screws to then secure the camera bar.
-
Page 18: Troubleshooting
Troubleshooting... - Page 19 Ensure the Wi-Fi network supports 2.4Ghz Display doesn’t boot or Android OS issue, generally a firmware upgrade hangs on LamasaTech required please contact the LamasaTech Customer Logo Success Team. No Display/black screen Check if you have a backlight as this may be a content...
- Page 20 Troubleshooting Issue Solution Screen Flashing on Please contact the LamasaTech Customer Success and off Team. Content not loading Check time zone on display as this can prevent signage from CMS application applications running correctly Display doesn’t boot Android OS issue, generally a firmware upgrade required...
-
Page 21: Contact Technical Support
Contact technical support cs@lamasatech.com UK: +44 (0) 191 622 0725 US: +1 (805) 308-9623 www.lamasatech.com...
Need help?
Do you have a question about the Versi Indoor Digital Signage Totem and is the answer not in the manual?
Questions and answers