Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MechMaxx SSFM-70
Summary of Contents for MechMaxx SSFM-70
- Page 1 WARRANTY Operator’s Manual www. mechmaxx.com...
-
Page 3: Table Of Contents
BOLT TORQUE USING THIS MANUAL ENGLISH TORQUE SPECIFICATIONS TERMINOLOGY METRIC TORQUE SPECIFICATIONS DEFINITIONS WARRANTY OWNER ASSISTANCE PARTS DIAGRAM SERIAL NUMBER PLATE PARTS LIST ASSEMBLY AND SET-UP TRACTOR REQUIREMENTS ASSEMBLY TRACTOR & WHEEL LOADER HOOK-UP DRIVELINE INSTALLATION www. mechmaxx.com TABLE OF CONTENTS... -
Page 4: Specifications
SPECIFICATIONS Model SSFM-70 Cutting Width 68in Total Width 72in Cutting Height Flow Range Low 18 gal/min Flow Range High 23 gal/min Auxiliary Pressure 2900psi Roller Diameter Rotor Bearing SKF bearing Number Of Hammer Blade Type Hammer Blades Size Of Hammer 4 X 2.6in... -
Page 5: Safety Signs
DO NOT go under frame when rotor is turning or engine BLADES is running. Keep others away. Disconnect & lockout power source BEFORE adjusting KEEP HANDS or servicing. Keep hands, feet, hair, and clothing away from moving AWAY parts. www. mechmaxx.com SAFETY SIGNS... -
Page 6: Important Safety Information
They are difficult to see, especially at nance and storage of equipment. night. • Flashing warning lights and turn signals are recom- mended whenever driving on public roads. Use lights and devices provided with implement. www. mechmaxx.com SAFETY... -
Page 7: Transport Machinery Safely
• The information contained within this manual was current at the time of printing. Some parts may change slightly to assure you of the best performance. www. mechmaxx.com SAFETY... -
Page 8: Terminology
SERIAL NUMBER PLATE For prompt service always use the serial number and model number when ordering parts from your dealer. Be sure to include your serial and model numbers in corre- spondence also. www. mechmaxx.com SAFETY... -
Page 9: Assembly And Set-Up
Hold the half-shafts next to each other in the shortest working position and mark them. b. Shorten inner and outer guard tubes equally. c. Shorten inner and outer sliding profiles by the same length as the guard tubes. www. mechmaxx.com SAFETY... -
Page 10: Operating Instructions
Proper servicing and adjustments are the key to the long life of any machine. With careful and systematic inspec- tion of the mower, costly maintenance, time and repair can be avoided. Before beginning to mow, the following inspection should be performed: www. mechmaxx.com UNPACHING THE CONTAINER... -
Page 11: Adjustments
When the belt has the correct tension the gearbox should be adjusted so that the gearbox extension is running straight (parallel) with the flail mower. Loosen bolts at the bottom of the gearbox and move gearbox until gearbox extension is running straight. www. mechmaxx.com CONTENTS SUPPLIED... -
Page 12: Maintenance And Lubrication
Do not overfill! 3. With tension relieved from belt remove old belt from IMPORTANT: Mower should be level when checking oil in pulleys. gearbox! 4. Tighten belt tension bolt. 5. Reinstall belt guard and belt guard fender. www. mechmaxx.com TO-SCALE HARDWARE... - Page 13 Driveline Profiles HOURS Type of Lubrication: Multipurpose Grease www. mechmaxx.com ASSEMBLY...
-
Page 14: Troubleshooting
Change mowing pattern. Reduce speed turns. Shift to a lower gear. Uneven cut Level mower. Replace missing knives. Mow at full throttle (540 PTO rpm). Shift to a lower gear. Tractor loaded down by mower Clean mower. www. mechmaxx.com ASSEMBLY... -
Page 15: Appendix
Check tightness of bolts periodically, using bolt torque chart as a guide. Replace hardware with the same trength bolt. ENGLISH TORQUE SPECIFICATIONS Bolt Torque SAE 2 SAE 5 SAE 8 Bolt Diameter lb-ft lb-ft lb-ft 1/4" 5/16" 3/8" 7/16" 1/2" 9/16" 5/8" 3/4" 7/8" www. mechmaxx.com KNOW YOUR MACHINE... -
Page 16: Metric Torque Specifications
Torque figures indicated above are valid for non-greased or non-oiled threads and heads otherwise specified. Therefore, do not grease or oil bolts or cap screws unless otherwise specified in this manual. When using locking elements, increase torque values by 5%. www. mechmaxx.com KNOW YOUR MACHINE... -
Page 17: Warranty
No other warranty of any kind whatsoever, express or implied, is made with respect to this sale; and all implied warranties of merchant-ability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale. www. mechmaxx.com OPERATION... -
Page 18: Parts Diagram
PARTS DIAGRAM www. mechmaxx.com OPERATION... -
Page 19: Parts List
350g Grease nipple M6*1 Bushing for hammer seat mount connector Euro Hitch Locking nut M16*1.5 Low linkage weldment Flail rotor weldement Bolt M12*35 Skid Left Rear Roller Locking Nut M12 bearing UC205 Cover weldment Left bearing seat www. mechmaxx.com OPERATION... - Page 20 Motor oil pipe assembling checking valve and priority valve head screw M12*50 protection plate 02 cover weldment Right skids Right Right connection plate for roller mower deck weldment head screwM12*45 Bolt M8*60 Nut M8 www. mechmaxx.com MAINTENANCE...
-
Page 21: Gearbox Assembly
GEARBOX ASSEMBLY PARTS LIST DESCRIPTION 63-1 deck 63-2 shaft 63-3 grease nipple M8*1 63-4 bearing 6208-Z 63-5 circlip 80 63-6 oil seal FB type 40*55*8 www. mechmaxx.com MAINTENANCE... - Page 22 G1/2 65-4 connector 65-5 oil pipe 01 65-6 connector 65-7 quick couple G3/8 65-8 Oil pipe 02 65-9 head screw M10*30 65-10 washer 10 65-11 oil pipe 03 65-12 oil pipe 04 65-13 oil pipe 05 www. mechmaxx.com STORAGE...
- Page 24 info@mechmaxx.com...
Need help?
Do you have a question about the SSFM-70 and is the answer not in the manual?
Questions and answers