3.2.4. Installing and Replacing the Battery When installing the battery, it is necessary to confirm that the clips have properly engaged with the locking mechanism. This prevents the battery from falling out. To remove the battery grip both depressable clips tightly and gently pull the battery from the casing.
Page 10
3.2.7. Connect to PC Step 1: Switch to PCVR mode and power on. Step 2: Connect the power adapter to the USB-HUB. Step 3: Connect the DP cable. Put two USB plugs into the USB-HUB, and the DP cable into the computer. Step 4: Connect the USB-HUB to the PC.Use the separate USB to USB cable.
Page 11
é During the pairing process, it is necessary to ensure that the headset is not in sleep mode. Step 5: Wait for the controller’s green indicator light to come on. Once the light comes on the Pimax Play will that the controllers...
Page 12
3.2.9. How to Adjust the Headset for a Comfortable Fit and View Step 1: Adjust the strap dial located on the back of the main strap to tighten or loosen the fit. Step 2: Fine-tune the top headstrap to adjust the headset’s vertical position on your face. Step 3: Fine-tune the length and position of the straps until you are comfortable with the fit and visual experience.
Page 14
3.3.3. Switching to Standalone VR mode If you switch between PCVR and Standalone mode while the headset is on, the headset will restart once automatically. This is normal behavior. 3.3.4. Powering on the Controllers Press and hold the π Button for seconds (blue light/green light always on) CAUTION READ CAREFULLY Before turning on the controllers, please charge the batteries for a period of time (>30 minutes) in advance to ensure that the...
Page 15
3.3.5. Powering on the VR Headset Press and hold the power button for 2s to turn on the headset. The first boot will take a long time to load, please leave the helmet for 1 minutes before use. 3.3.6. How to adjust the Headset for a Comfortable Fit and View Step 1: Adjust the strap dial counter-clockwise to open the strap to it’s widest setting.
Page 16
$$ÈÇ"!!Æ#ÅÄÉà('%&467852&38006) (¶%&¿6H5&¹HQ 'X%&f6g2C&¢H b 72 ※W x|³«åu| (A%&U0H08Q&P)EGFH06C (Â%&ÑÈ2& CHFG)&¢H52CH ³«¦u x| 'e%& 6 p &U0CH p (X%&f6g2C&38006) U j u u yw (Ô%&fC6ÛG5G0È&U2)Q6C vu y ùyx| å ö r¦ '%& B H002CÈ&U h 2H0 h yts uurxö vrqv xp '%&U0CH p &kGH7 '(%&f¢h A ig&UgG0F h (e%&pG)Glmkpi&ihg '¶%&...
3.3.9. How to Update Firmware Open the Pimax Client on your PC. Navigate to "Device Settings → Check for Updates" in the client. Pimax Client; The system will check the currently installed software and firmware version, and will prompt you to perform an update if there is a new version available on the server.
4. Parts replacement 4.1. Lens replacement Step 1: Carefully unscrew and remove the mounting Step 2: Gently grasp the edge of the lens, rotate and lift screws on the lens; the lens to remove it; Step 3: Install the lens to be replaced on the lens barrel, Step 4: Put the mounting screws back into their original and gently press the edge of the lens bracket to position and tighten gently but firmly;...
Page 21
Step 2: Install and fasten the another Cover to be replaced according to the interface. CAUTION READ CAREFULLY When replacing the Cover, it is necessary to disconnect the power supply of the device, disconnect the DP cable and wear anti- static gloves.
Need help?
Do you have a question about the Crystal and is the answer not in the manual?
Questions and answers