Related Manuals for Dekema AUSTROMAT D2
Summary of Contents for Dekema AUSTROMAT D2
- Page 1 OPERATING INSTRUCTIONS A U S T R O M A T Version 2 DEKEMA Dental-Keramiköfen GmbH Industriestrasse 22 D-83395 Freilassing (Germany) Tel. +49 (0) 86 54 / 46 390 Fax +49 (0) 86 54 / 66 195 www.dekema.com info@dekema.com...
-
Page 2: Table Of Contents
OPERATING ELEMENTS AND PROGRAM PROCEDURE ..........15 PROGRAMMING ........................18 THE SETUP MENU ........................ 19 PRINTING RECORDS AND CONNECTING TO A PC..............22 ........................22 RINTING RECORDS ® (DREAM )..................... 24 CONNECTION PRACTICAL TIPS.......................... 25 ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... -
Page 3: Introduction
Please keep the packaging material (two boxes and foam material to protect against knocks during transport) in case you need to ship the equipment at a later date. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... -
Page 4: Technical Specifications
~ 100 V 95…105 VAC / 50 – 60 Hz Nominal suction capacity 24 l / min Weight 6 kg DEKEMA does not take upon liability for damage caused by using another vacuum pump than delivered. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... -
Page 5: Description Of Equipment
Firing objects (including firing trays) rising above the height gauge may not be placed onto the firing table. The thermocouples in the firing room can be da- maged. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... - Page 6 . The following connections are available: one plug connection with two clips to hold the soft or memory module for data storage, two serial interfaces for PC connection. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005...
-
Page 7: Safety Measures
(turn off the furnace and pull the plug). The main switch is on the back (see p. 8, Fig. 2). • If a lightening stroke hazard exists, separate the furnace from the power source (turn it off and pull the plug). ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... -
Page 8: Set-Up
Never directly contact hot parts of the furnace. Do not grasp the lift seat, firing table or firing object with your bare hands. Never put your hand into the hot firing chamber. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... - Page 9 If technical servicing or repairs are necessary, they should only be performed by authorized professionals. After repair work, the furnace must undergo a safety check: Federal Republic of Germany VDE 0701 International according to the respective national guidelines ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005...
-
Page 10: Start-Up
Step 7: After it is turned on, the furnace waits approximately 30 seconds and automatically heats up to the starting temperature of the preheating program or the program that has been set. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... -
Page 11: Maintenance And Service
• Make sure that the heating element and thermocouple are not damaged. • Only use the DEKEMA calibration set that is for the specific furnace. This consists of a curved silver wire and a white ceramic firing tray. • Make sure that the temperatures of all the firing programs are adjusted when the CCF value changes. -
Page 12: Self-Check
This is the case for example when the heating element is too old, and you want to reach a firing temperature quickly. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... -
Page 13: Replacing The Battery
If the self-check program is run regularly (see Section 7.3), a recommendation will be displayed when the heating element wear has exceeded the permissible limit. Follow the accompanying installation and safety instructions in Section 4 to install the replacement heating element. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... -
Page 14: Service And Transport
Turn off the device and pull the pump plug. • Only use the original box and the supplied packaging material. 6.7 REPLACEMENT PARTS Only use original DEKEMA parts for servicing and maintaining the oven. Contact your service partner, or contact DEKEMA directly. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT... -
Page 15: Operating Instructions
Vacuum level in % (100): After preheating, the firing chamber VAC % is evacuated. The vacuum is held until the final temperature is reached and then time [VAC HOLD] is held. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... - Page 16 (if several users share the furnace). This key is used to open the Setup menu. The available functions are SETUP described in Section 7.3. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005...
- Page 17 Simply copy firing programs to different memories. COPY Press EDIT to enter the programming mode. E DI T Confirms entered data with the ENTER key. The cursor jumps to the next E N T E R parameter. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005...
-
Page 18: Programming
However, there is a restriction that only the values of unprocessed program steps may be edited. Note also that a change in the running program is accepted and stored (no provisional programs). ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... -
Page 19: The Setup Menu
PC must be connected and suitable software installed for data recording (cf. Section 8). Temperature calibration temperature calibration please DEKEMA calibration set and preheat the furnace. Press "START" to launch the calibration program. The program runs automatically and lasts approx. min. During... - Page 20 The structure and interpretation of the diagnosis data are important for the service personnel (see also the "Diagnosis data" menu item). The data have little significance for the user. Thus they are not detailed here. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005...
- Page 21 The data have little significance for the user. Thus they are not detailed here. Service funktions The service functions are password-protected and are only available to authorised service personnel. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005...
-
Page 22: Printing Records And Connecting To A Pc
In any case, you can manually print out a record after a firing is completely finished. You can obtain as many additional copies of the printout as you want by pressing the function key Print. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... - Page 23 DENTIN 1 Program procedure: 3:00 Close 3:00 Preheat 2:00 Firing temperature 1:00 Cool -:-- Relax -:-- VAC (level) Starting the program 16:24:56 Air pressure Total firing time 00:17:10 Firing processed correctly ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005...
-
Page 24: Pc Connection (Dream )
8 Printing Records and Connecting to a PC ® 8.2 PC CONNECTION (DREAM ® DREAM (DEKEMA Remote Access Management) is software for the external AUSTROMAT ® programming, archiving and quality management of your ® DREAM supports you in the following tasks: Administering and archiving firing programs. -
Page 25: Practical Tips
If you activate fast cooling with the pump, you should not place the firing object on the firing table until cooling is completed, as otherwise the temperature may be too high for drying. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005... - Page 26 Also, save your firing programs regularly on an optionally available memory module. You should at least note down your firing program parameters on paper or save on PC. ® DEKEMA Dental-Keramiköfen GmbH, AUSTROMAT D2, Version 2, 2005...
Need help?
Do you have a question about the AUSTROMAT D2 and is the answer not in the manual?
Questions and answers