Subscribe to Our Youtube Channel
Related Manuals for Kind KD-ZP30R
Summary of Contents for Kind KD-ZP30R
- Page 1 ORBIT ROBOT CAMERA KD-ZP30R Installation and Use Manual Before use, please read this manual carefully and store it properly for future use...
-
Page 2: Safety Precautions
SAFETY PRECAUTIONS 1. During the installation of this device, please carefully read this safety guide and strictly follow the installation and use instructions for operation. Properly keep this manual for future use. 2. Before connecting the switch power supply of this device to an external power supply, please confirm the voltage value of the power supply. - Page 3 SERVICE AND DISCLAIMER The information provided in this manual is for reference only. KING has always strived to provide accurate, complete, and appropriate information. However, KING cannot rule out the possibility that some information in this manual may be incorrect or incomplete, and this manual may contain typos, missing or incorrect information.
-
Page 4: Table Of Contents
CATALOG 1. Product Overview......................5 2. Component introduction.....................5 1. Shooting orbit system.....................6 2. Shooting lifting system....................7 3. Power supply and battery system................7 4. Camera system.......................8 5. Precision intelligent shooting control system............9 6. Wireless audio and video transmission system............12 3. Installation instructions....................13 1. -
Page 5: Product Overview
2. COMPONENT INTRODUCTION KIND orbit robot camera consists of six parts, namely the shooting orbit system, shooting lifting system, power supply and battery system, camera system, precision intelligent shooting control system, and wireless audio and video transmission system. -
Page 6: Shooting Orbit System
1. Shooting orbit system Shooting orbit: This orbit is molded and CNC precision machined, with a surface that has undergone multiple grinding treatments, resulting in a delicate and smooth texture. The stainless steel bullet head seamlessly connects. Orbit size: 100cm in length, 25cm in width, and 5cm in height, with straight and curved orbit that can be spliced and combined as needed, supporting roof lifting or ground installation. -
Page 7: Shooting Lifting System
2. Shooting lifting system Using a precision three-stage ball screw servo electric cylinder, the diameter of each section is Ø 145mm Ø 125mm Ø 105mm. Initial ≤ 700mm, travel 800mm, no shaking during starting, braking, and driving. Repetitive positioning accuracy ± 0.01mm, rated thrust 0.42KN, programmable positioning, integrated control. -
Page 8: Camera System
4. Camera system(For the installation method of PTZ, please refer to the KD-A800PTZ manual) Using KIND broadcast grade PTZ camera KD-C25 and KD-C1000, and customized matching has been made for the internal power supply structure, wireless control, and video wireless transmission of the camera. -
Page 9: Precision Intelligent Shooting Control System
9. WiFi antenna 10. USB port 11. 12V power supply 5. Precision intelligent shooting control system Main functions: record and play video tracks, control the camera and orbit car's forward, backward, push, pull, shake, shift, and focus. 1. Control the camera's push, pull, shake, tilt, and settings. The settings menu includes functions such as white balance, focus, shutter, IRIS, etc. - Page 10 1. Record the trajectory of the orbit car and camera, the button light is on to start recording, the button light is off to stop recording. 2. Play the recorded track of the orbit car and camera, the button light is on to start playing, the button light is off, and the playback is complete.
- Page 11 15. Adjust the focal length through a knob. 16. Manually adjust the ISIR by rotating the knob to adjust the ISIR. 17. The SHUTTER PRI button light is on, and the knob can adjust the shutter speed; The SHUTTER PRI button light is off, and the knob can adjust the movement speed of the rail car and camera, with a total of 8 gears.
-
Page 12: Wireless Audio And Video Transmission System
6. Wireless audio and video transmission system Wireless transmission of HD 1080p images to a monitor. High performance and powerful remote signals are transmitted through walls, floors, and ceilings, with a maximum range of up to 100 feet (with streaming line of sight for maximum range). Easily send clear, uncompressed high-definition videos and digital audio. -
Page 13: Installation Instructions
3. INSTALLATION INSTRUCTIONS 1. Orbit installation... - Page 14 Ground installation 1. Install the support foot on the support brackets, with 2 support foot installed on each bracket. The depth of each support foot inserted into the installation bracket should be consistent for easy horizontal adjustment in the future. 2.
-
Page 15: Pulley Car Installation
4. Lock the screw on the locking nut. Attention: Paste the horizontal position sensing sticker. Pay attention to the direction and interface. The first half of the orbit is covered with a pure black sticker, while the rest are covered with black and white stickers. -
Page 16: Lift Rod Installation
3. Lift rod installation Place the lift rod gently on the pulley car, align the lift rod with the fixing hole on the pulley car, and tighten the 6 fixing screws. -
Page 17: Camera Installation
Plug in the camera control cable (six pin round mouth at the tail of the lift rod), plug in the motor control cable (IN port of the lifting rod motor), and the installation is complete. 4. Camera installation Place the camera on the flange of the lift rod and secure it with 2 1/4 British standard screw. -
Page 18: Battery Installation
5. Battery installation The dedicated magnet is installed in a specific area on the back of the battery, and the red light on the battery lights up, indicating that the battery is in 28.2V output mode. -
Page 20: Reduction Bracket Installation
Without using a battery, the battery base has a power cord interface that can be directly powered using a power adapter. 6. Reduction bracket installation Install reduction brackets at the starting and ending points of the orbit, paying attention to the installation direction, with the spring facing the orbit. -
Page 21: Debugging And Use Instructions
4. DEBUGGING AND USE INSTRUCTIONS 1. Position sensor Push the orbit car to the end of the track. Turn on the power switch of the orbit car and confirm that the two red light spots emitted by the position sensor fall on the sensor sticker. The orbit car will slowly move towards the starting point of the track when executing the self check program. -
Page 22: Preset Bit Setting, Calling, And Clearing
5. Preset bit setting, calling, and clearing 1. Set preset bit. Control the orbit car and camera to the desired preset position, select the preset bit number to be set by pressing the number buttons 1-9 in the preset area on the keyboard, and press the SET button to set. -
Page 23: Remote Control
8. Remote control 1.HOME：The camera returns to its initial position 2.CAMERA：To switch the control camera address, it needs to correspond with the camera dialer, and once it corresponds, the camera can be set up 3.FOCUS AUTO：Auto focus 4.FOCUS MANU：Manual focus mode 5.PATTERN 1：4Kp30 signal switching (takes effect after setting and restarting the camera) 6.PATTERN 2：1080i50 signal switching (takes effect after setting and restarting the camera) 7.TRIG WB：One click white balance... -
Page 24: Ptz Camera Menu
18.CLEAR：Clear preset bit button. Select the preset bit you want to delete and click the CLEAR button to clear it. 19.Number button：9 preset bit. After turning on the camera, if the lens is not in the initial position (the lens will be in the center position after turning on the camera), first press the number 0 button, then press the CLEAR button, power off and restart the camera. - Page 25 BRIGHT GAIN SHUTTER...
- Page 26 MANUAL FOCUS AUTO MANUAL...
- Page 27 AUTO OUTDOOR INDOOR ONE PUSH...
-
Page 28: Packing List
SYSTEM COLOR IMAGE Attention: In case of camera malfunction or abnormal parameters, it is recommended to restore the system to its default values. 5. PACKING LIST Straight/curved orbit Support bracket Hand screw (short) Support feet (ground mounted) Lifting screws (non-standard for ceiling installation) Orbit car Lifting rod (including fixing screws) Control keyboard and power adapter... -
Page 29: Ater-Sale Service
6. ATER-SALE SERVICE Dear user, in order to ensure that you fully enjoy high-quality service, please carefully read the following product service regulations. Our company provides limited warranty and lifetime repair services 1. The warranty period is 12 months from the date of sale. During the limited warranty period, you will enjoy free warranty service for product malfunctions, which will be sent by the user to the company for repair (malfunctions caused by improper use, human error, or force majeure are not covered by the warranty).
Need help?
Do you have a question about the KD-ZP30R and is the answer not in the manual?
Questions and answers