Page 1
FORWARD Respected user: Sincerely thank you for choosing the B125-15 two-wheeled riding motorcycle designed and produced by our company! This model is developed and produced by our company based on advanced technology and avant-garde design concepts at home and abroad. We hope that it can bring you a safe driving process and a comfortable driving experience! Before you drive the motorcycle, please fully read the regulations and requirements in this practical manual!
Page 2
IMPORTANT NOTICE When operating and driving the vehicle, please operate in accordance with the provisions of this instruction manual, and strictly abide by the national and local traffic laws and regulations, and always pay attention to your personal safety! This maintenance manual is one of the necessary accessories of this car. When the car is sold to others, please attach it with the car.
CONTENTS I. User notice......................................1 1.1.Safety instructions for motorcycle drivers..........................1 1.2.Number position (Figure 1)..............................1 II. Brief introduction of two-wheeled motorcycle..........................2 2.1.The range of application of two-wheeled motorcycles......................2 2.2.Features of two-wheeled motorcycle........................... 2 2.3.Carrying regulations................................2 2.4.Fuel oil....................................2 2.5.Electrical appliances................................2 2.6.inspection....................................
Page 4
XVI. The service life of the vehicle and the disposal of the vehicle....................33 . Motorcycle related adjustment data............................33 XVII XVIII. Main technical parameter table............................. 34 XIX. Common faults and causes of motorcycles..........................35 XX. BD125-15 electrical schematic diagram.............................37...
I.User notice 1.1Safety instructions. For your personal and vehicle safety, please abide by the following six regulations: 、Wear all kinds of protective equipment correctly. Riding protective equipment includes safety helmets, goggles, knee pads, elbow pads and gloves. Wearing protective equipment can greatly reduce the injury to your body during an accidental crash and protect your personal safety to the utmost extent.
ENGINE NO. II.Brief introduction of two-wheeled motorcycle The two-wheeled motorcycles with compact structure and a unique novel appearance . very comfortable riding and pretty stable,All models are adopted with electronic fuel injection system ,which is more environmentally , lower fuel consumption and emissions , meeting emission requirements.
III.Safe driving motorcycle. The motorcycle is a two-wheeled motor vehicle, which can bring convenience and fast lifestyle to the rider. In order to ensure the best performance of your motorcycle, you must maintain it correctly. the motorcycle must be safe and well-performance;...
note: Improper loading or overweight motorcycle cargo will damage the performance of the vehicle and affect the driving stability of the vehicle. Modification of motorcycles or removal of original parts may result in reduced vehicle safety or illegal operation. Please follow all regulations in your area.
IV. Instructions for use 4.1.Parts position 1.(Fig.1) ①L rear mirror ②headlight ③FL turn single light ④battery) ⑤cushion ⑥rear license ⑦RL turn single light ⑧front brake clipper ⑨gear lever ⑩FL pedal ⑪single support ⑫RL single support Fig.1 2.(Fig.2) ①R rear mirror ②FR turn single light ③VIN ④Tank cover...
Page 10
4.2.Instrument and ignition switch. Fig.4 Instrument (Fig.4) Please refer to the table for the names and functions of indicator symbols. Code No. Title Function Speed indicator Instantaneous speed of the vehicle Mileage indication The total mileage of the vehicle Gear indication Display the gear position of the engine Fuel quantity indicator Display the amount of fuel left in the fuel tank...
4.3.Ignition switch. The ignition switch lock (Figure 5) is set in front of the steering handle, and the ignition switch must be turned on before starting the motorcycle. The key position and function are shown in Table 2. Key position Function Key state The circuit is disconnected and the engine...
When the switch is in this position, the headlights, position lights and taillights are on. headlight“ ” ” When the switch is in this position, the position light and tail light are on. Position light“ When the switch is in this position, the headlights, position lights and taillights will be OFF“...
4.6.Headlamp pitch angle adjustment (Figure 8) Due to the different heights and observation habits of users, there are different needs for night driving lighting. In order to give users a better night driving experience, the headlights of Jingira are specially designed to adjust the pitch angle.
Page 14
Make sure the tire status. Incorrect tire specifications will affect the handling performance of the motorcycle. Damaged and scratched tires can cause tire failure and cause the vehicle to lose control. Excessively worn tires can puncture the tires and cause the vehicle to lose control. Tire wear also affects tire shape and handling performance.
V. Operation guidance 5.1. New motorcycle running-in The running-in period refers to a treatment method that is carried out in order to ensure that the joint surface between the parts and the parts becomes the best joint state during the initial use of the new car. The correct running-in operation can maximize the life of the vehicle.
Page 16
3. Check whether the coolant in the cooling system is sufficient and ensure that there is no leakage; 4. Check the front and rear brakes: free travel (5-10mm front, 10-20mm rear), smooth operation; 5. Check the front and rear tires: the air pressure, the depth of wear of the tread pattern, and the cracks (see page 20); 6.
Page 17
Note: 1、After starting, warm up for 2-3 minutes before driving on the road. Engines with insufficient preheating temperature will aggravate the wear of cylinders, piston rings, rocker arms and other parts during driving. 2.When using the electric start button “ ”,it should be released immediately within 3 to 5 seconds each time it runs;...
Page 18
Waning: 1. It is strictly forbidden to shift gears when the throttle is not returned and the clutch handle is not held tightly, otherwise it will easily cause damage to the engine and transmission system and cause safety accidents. 2. When shifting gears, please make sure that the shift lever has been stepped on, and then release the clutch handle. 3.
5.4.3, use the brake 1) When you need to slow down, you must use the front and rear brakes at the same time. (Slowly hold the front brake handle with your right hand and slowly step on the rear brake pedal with your right foot to avoid using the front and rear brakes separately).
Page 20
Every 40 hours driving or 1000km/I; every 80 hours driving or 2000km/C; every Air filter element Remarks① 8000km/R driving Spark plug Every 2000km or 80 hours/I; every 8000km/R Engine lubricating oil Replace once when a new car is 1000km, and then every 4000km or so. Lubricating oil filter Replace once when a new car is 1000km, and then every 4000km or so.
6.2. Inspection, selection and replacement of engine lubricating oil The effect of lubricating oil on the engine: reducing friction, increasing sealing, cooling parts, cleaning parts and preventing rust. If the quality of lubricating oil is poor, the use time is too long, or the amount of lubricating oil is insufficient, etc., it will accelerate the wear of engine parts and reduce the service life of the engine;...
lubricating oil. Check and confirm that there is no oil leakage, and then install the filler plug. 1、5. Run the engine at different speeds for 3 minutes. During operation, check whether the disassembled parts are leaking. Wait for the engine to stop for 3 minutes. In the idling state, the oil level is still lower than the scale line under the oil window, and an appropriate amount of lubricating oil should be added.
4. Check the electrode gap with a high-precision feeler gauge, the normal electrode gap is 0.8 ~ 0.9mm. 5. When installing the spark plug: first screw the spark plug into the thread by hand, and then tighten it with a spark plug socket wrench.
Page 24
2. Check whether the rotation of the throttle control handle is flexible from the fully open position to the fully closed position; whether it can automatically return to the position when the handle is released. 3. Check whether the throttle cable is flexible and good. Fig.19 [Adjustment] 1.
6.5. Adjustment of clutch (Figure 20) The free stroke of the clutch handle is: 5-10mm. The role of the clutch: (Figure 20) 1. The engine crankshaft and the variable speed transmission system can be combined smoothly and softly to ensure a smooth start of the motorcycle.
Page 26
broken. This will cause the belt to lose tensile strength and tear, and there is a danger of failure! ●Avoid kinking, bending, twisting, knotting or turning over the belt, and never use it as a belt whip. ●Do not lift the belt with the sprocket during installation. ●Do not use (sharp-edged) tools to tamper with the belt.
Notice: Before each ride, check whether the transmission system is working properly. If you notice any defect or damage, you must check and repair it immediately, and replace the parts of the transmission system if necessary, and the parts can only be obtained from a qualified dealer. Your dealer can recognize any signs of wear and can replace parts that are needed if necessary.
replace the brake disc. If the brake disc is damaged, cracked or deformed: please replace the brake disc Brake disc wear limit Front Rear warning: 图 25 前制动摩擦片检 The wear of the brake disc will reduce the thickness of the brake disc within the contact surface of the brake 查...
X.Inspection and adjustment of rear brake [Check] (Picture 27) ●The free stroke of the brake pedal after measurement is: 10-20mm. ●Measure the thickness of the rear brake disc and brake pad thickness. ●Check the oil level in the oil cup; check whether the brake caliper is normal; check the brake oil pipe and brake oil cup for oil leakage or cracks;...
10.2 Check the brake pads of the rear brake Check the minimum thickness of the brake pads (A). The minimum thickness of the brake friction pad: A=1.5mm. If the thickness is lower than the minimum thickness: please replace the friction plate in time. If the friction plate is found to be damaged or cracked: please replace the friction plate in time Figure 29 Inspection of rear brake friction lining...
Page 31
6. Remove the battery. installation: 1. The installation sequence is opposite to the removal steps. 2. Install the positive lead (╋) first, and then install the negative lead (━), and make sure the positive and negative The pole terminal is not loose, and the positive and negative poles cannot be reversed. Reverse connection will damage electrical parts.
Page 32
Instructions for use and maintenance of the engine water cooling system [Cooling System] (Figure 23) The cooling system can prevent the engine from overheating, and the correct use and maintenance of the cooling system can extend the service life of the engine.
Page 33
2. Unscrew the water tank cover; 3. Pour the cooling liquid from the mouth of the water tank, and add the cooling liquid to the position of the upper scale line; Figure 33 Adding coolant 4. Close the water tank cover. [Storage of Coolant] 1.
Page 34
NOTICE: 图 35 Please go to the designated dealer to adjust the shock absorption. The dealer has professionals and professional tools to adjust the shock absorption! ! The stroke of the left and right shock absorbers must be the same, otherwise it will adversely affect the riding safety! !
Step 1: Remove the fuel tank. Step 2: Remove the cylinder head cover and use the corresponding tool to remove the engine cylinder head cover. Step 3: Adjust the valve clearance of the rear cylinder: Rotate the magneto rotor to align the scale line of the rear cylinder alignment with the arrow, and confirm that the scale line of the sprocket and the arrow are also aligned at the same time, as shown in the figure.
1. Clean and dry the motorcycle, and wax the painted surface of the whole car. 2. Drain the fuel out of the fuel tank and spray anti-rust agent into the fuel tank. 3. Thoroughly drain the oil and refill the crankcase with new oil. 4.
N·m Torque value of tightening nut of rear wheel axle: 70~90 N·m Torque value of fastening bolts of front shock absorber and upper connecting plate: 10~14N·m Torque value of fastening bolts of front shock absorber and direction column: 20~25 N·m Torque value of engine suspension fastening nut: M8: 18~25 N·m, M10: 30~40 N·m XVIII.
engine Maximum net power 10.3kw/8500rpm Maximum torque 14.5N.M/6500rpm Bore*Stroke 42*45 Idle speed 1600±100 Engine lubricating oil Grade 15W-40 Lubricating oil capacity 2.2L Fuel grade 95# and Above Spark plug gap 0.8~0.9 mm Primary speed ratio 3.238 First gear ratio 2.42 Second gear ratio 1.53 change...
Page 40
Valve timing failure Check or replace Excessive carbon deposits on intake and exhaust valves Valve piston Repair or replace and pistons: poor fuel quality and poor oil quality clutch Clutch slip: poor oil quality, long use time, overload Adjust or replace Cylinder block, Cylinder block and piston ring wear: poor oil quality, long Change the oil...
power supply The cooling/cylinder temperature sensor is shorted to P0117 ground The cooling/cylinder temperature sensor is open or P0118 shorted to the power supply P0122 Throttle position sensor is open or shorted to ground P0123 Throttle position sensor shorted to power supply P0131 Oxygen sensor (one cylinder) is shorted to ground The oxygen sensor (one cylinder) is shorted to the power...
Need help?
Do you have a question about the Chinchilla 125 and is the answer not in the manual?
Questions and answers