TownSteel TDC 40 Series Installation Instruction

PARALLEL ARM MOUNTING （ PUSH SIDE ）
TECHNICAL DIMENSIONS ：
(SCREWS FOR SHOE PLATE)
M6x15 P.H.M.S (4) ST6.3X30 P.H.M.S (4)
3 3 "
8
1
2 "
3
8 "
8
DOOR 3
"
4
STOP
4"
A
SCREWS FOR SHOE M6X9 P.H.M.S (2)
HINGE CENTER
STOP FACE
3
4 "
4
2 1 "
4
B
1" 3" 1"
LEFT HAND
INSTALLATION DIMENSIONS ： SCREWS FOR CLOSER
M6X55 P.H.M.S (4), ST6.3X75 P.H.M.S(4)
Opening "B"
"A"
To 100
9
7 15 " 8 "
16 32
BEFORE INSTALLING MOUNTED STOP FACE (PARALLEL ARM), TURN BACK CHECK SELECTOR VALVE (FOUND
To 120 6 31 " 9
7 "
32
32
IN OPPOSITE SIDE OF CLOSER FROM REGULATING SCREWS SIDE) ALL THE WAY IN (CLOCKWISE) !
Over 140
6 3 "
6 1 "
16
2
OPEN END WRENCH 30 °
FOREARM SCREW
SHOE
SHOE PLATE
ARM SCREW
MAIN ARM
BACKCHECK AND OPTIONAL
DELAY ACTION VALVE
LATCH SPEED
VALVE
MAIN SPEED
BACKCHECK AND
VALVE
OPTIONAL DELAY ACTION
SELECTOR VALVE SCREW
REMOVABLE INSERTS
SHAFT
TO HAND COVER
IMPROPER INSTALLATION OR REGULATION MAY RESULT IN PERSONAL INJURY
！
Caution
OR PROPERTY DAMAGE. FOLLOW ALL INSTRUCTIONS CAREFULLY PLEASE.
4 of 4
3 3 "
8
1
2 "
8
3
"
8
3 DOOR
"
4
STOP
4"
A
HINGE CENTER
STOP FACE
3
4 "
4
2 1 "
4
B
1" 3" 1"
RIGHT HAND
Measured from hinge Center
Do not scale drawing
INSTALLATION STEPS:
1. Adjust spring power to match door width as
indicated by chart on page 1.
2. Mount closer on door to dimensions shown, tube end
toward latch. Locate closer and shoe from center of
hinge.
3. Attach arm as follows:
( A ) Place open end wrench on bottom shaft and turn
toward hinge jamb about 30 ° .
( B ) Place main arm on top shaft, insert arm screw into
top of shaft and tighten.
4. Attach PA shoe plate to stop as shown.
5. Attach rod and shoe to shoe plate as shown. (Offset
toward hinge)
6. Open door and insert rod in forearm, and Close door.
7. With main arm parallel to door, insert forearm screw
and tighten.
REGULATION
BACKCHECK
ATTACH COVER
SAME AS PAGE 2 OR PAGE 3.
YW2332
TDC 40 SERIES DOOR CLOSERS
INSTALLATION INSTRUCTION
MOUNTING TYPES:
Standard (Pull Side) Top Jamb (Push Side)
Permit 130 ° maximum opening. Permit 130 ° maximum opening.
See Page 2. See Page 3.
PLEASE READ THIS INSTRUCTION CAREFULLY BEFORE INSTALLATION; WE WON'T BE
！
Caution
RESPONSIBLE FOR ANY RESULTS WHICH ARE CAUSED BY THE WRONG WAY OF MOUNTING,
GENERAL NOTES
Closer is non-handed and designed to meet entrance
accessibility requirements. Before installation, determine
hand of the door. Then Select degree of door opening.
Refer to the drawing (Below and Over). Adjust the spring
power as shown before installing the closer. Turn the spring
adjustment nut clockwise (CW) or counter-clockwise (CCW)
the required number of turns to match door width as indicated
in the chart.
To decrease
spring power
CCW _
+
CW
To increase NOTED! Adjust spring power DO NOT exceed the maximum turns in either direction!
spring power
HOW TO TELL HAND OF DOOR.
Right hand door
Left hand door
YW2332
Model:TDC 40 Size 1-6
Parallel Arm (Push Side)
Permit 140 ° maximum opening.
See Page 4.
DOOR
MAXIMUM DOOR WIDTH
WEIGHT
Spring
Exterior Interior Full turns
LBS (KGS)
Power
doors doors required
-5 TURNS CCW ---55 ( -25)
1
2
8.5 lb-f -2 TURNS CCW
34"
55-99 (25-45)
3
30" 38" 0 TURNS
99-143 (45-65)
5 TURNS CW
36" 4 143-187 (65-85)
48"
5 187-264 (85-120)
42" 54"
10 TURNS CW
48"
60" 6 264-330 (120-150)
15 TURNS CW
MAX. 20 Turns from the Min. setting.
The factory preset size 3 (original).
CLOSING CONTROL
BACKCHECK
OPTIONAL DELAY ACTION
MAIN SPEED
LATCH SPEED
1 of 4