Advertisement
Heritage Oval Extension Table
Assembly | User Guide
Two people required for safe assembly
Opening Boxes: DO NOT use a knife to open the packaging as you may damage
your furniture. Peel-off the tape, then lift and separate the cardboard flaps to open.
Please follow these Assembly | User Guide Instructions
Product Care
KING LIVING CUSTOMER CARE: kingliving.com/support
Advertisement
Table of Contents
Related Manuals for King Living Heritage Oval Extension Table
Summary of Contents for King Living Heritage Oval Extension Table
- Page 1 Heritage Oval Extension Table Assembly | User Guide Two people required for safe assembly Opening Boxes: DO NOT use a knife to open the packaging as you may damage your furniture. Peel-off the tape, then lift and separate the cardboard flaps to open.
-
Page 2: Table Of Contents
Contents Assembly Aligning Table Top Correct Use of Extension Table Troubleshooting Calibrate Table for Closed Use Calibrate for Extended Use KING LIVING CUSTOMER CARE: kingliving.com/support... -
Page 3: Assembly
Assembly x1 (4mm) KING LIVING CUSTOMER CARE: kingliving.com/support... - Page 4 Attaching Legs to Frame Attaching Legs to Frame KING LIVING CUSTOMER CARE: kingliving.com/support...
- Page 5 Flip Table Over WARNING Leaning table on side can 2 People Required cause damage to legs Cut Zip Ties KING LIVING CUSTOMER CARE: kingliving.com/support...
- Page 6 Screw in Bolt KING LIVING CUSTOMER CARE: kingliving.com/support...
-
Page 7: Aligning Table Top
Aligning Table Top How to Correct Table Top Alignment Correcting Extension Foldout Alignment Completely open table, push ends inward and hold whilst second person tightens bolt completely KING LIVING CUSTOMER CARE: kingliving.com/support... - Page 8 Securing Table Top Alignment Note: Tighten bolts firmly Correcting Table Top Levels When Closed KING LIVING CUSTOMER CARE: kingliving.com/support...
- Page 9 Correcting Table Top Levels When Closed KING LIVING CUSTOMER CARE: kingliving.com/support...
- Page 10 Correcting Table Top Levels When Extended Correcting Table Top Levels When Extended KING LIVING CUSTOMER CARE: kingliving.com/support...
-
Page 11: Correct Use Of Extension Table
Opening and Closing Extension Table When opening and closing table, always push and pull from middle of table top ends. Pushing and pulling from side of table top ends can cause misalignment and damage to the table. KING LIVING CUSTOMER CARE: kingliving.com/support... -
Page 12: Calibrate Table For Closed Use
Loosen, but do not remove, the mounting bolts holding the table tops to the sliding rails. This allows the tops to slide in all directions, giving better access to the leveling bolts for height adjustment on each side. KING LIVING CUSTOMER CARE: kingliving.com/support... - Page 13 Bolts should have factory-applied thread lock glue; if missing or previously adjusted, reapply before tightening. Avoid over tightening to avoid affecting leveling or deforming the sliding rails. If Alignment is incorrect, follow steps 6-9. KING LIVING CUSTOMER CARE: kingliving.com/support...
- Page 14 With table tops being held in place, have the second person locate the leveling screws on the underside of the table tops. Access to leveling bolts may require sliding table tops back and forth when mounting bolts are loose. KING LIVING CUSTOMER CARE: kingliving.com/support...
- Page 15 Bolts should have factory-applied thread lock glue; if missing or previously adjusted, reapply before tightening. Avoid overtightening to avoid affecting leveling or deforming the sliding rails. If level still not correct repeat steps 6-9 making minor adjustments with care. KING LIVING CUSTOMER CARE: kingliving.com/support...
-
Page 16: Calibrate For Extended Use
Slowly close the table by pushing the ends inward from one side. Check that the alignment pins (A) line up before fully closing the table tops. KING LIVING CUSTOMER CARE: kingliving.com/support... - Page 17 Bolts should have factory-applied thread lock glue; if missing or previously adjusted, reapply before tightening. Avoid overtightening to avoid affecting leveling or deforming the sliding rails. If Alignment and Levels are incorrect, follow steps 6 - 10. KING LIVING CUSTOMER CARE: kingliving.com/support...
- Page 18 With table tops being held in place, have the second person locate the leveling screws on the underside of the table tops. Access to leveling bolts may require sliding table tops back and forth when mounting bolts are loose. KING LIVING CUSTOMER CARE: kingliving.com/support...
- Page 19 3. Rotate the adjustment feet 1/2 turn each until the extension leaf is level with the table top ends. To raise extension leaf, rotate clockwise. To lower extension leaf, rotate anti-clockwise. KING LIVING CUSTOMER CARE: kingliving.com/support...
- Page 20 Bolts should have factory-applied thread lock glue; if missing or previously adjusted, reapply before tightening. Avoid over tightening to avoid affecting leveling or deforming the sliding rails. If level still not correct repeat steps 6-10 making minor adjustments with care. KING LIVING CUSTOMER CARE: kingliving.com/support...
Need help?
Do you have a question about the Heritage Oval Extension Table and is the answer not in the manual?
Questions and answers