Advertisement

Quick Links

MEX-M71BT/N5200BT
SERVICE MANUAL
Ver. 1.0 2016.12
The service manual of the mechanism deck, used in
this model, has been issued in a separate volume.
Please refer to the service manual of the MG-101
series for the mechanism deck information.
• The tuner and CD sections have no adjustments.
(M71BT/N5200BT : US, CND)
FOR THE CUSTOMERS IN THE USA. NOT
APPLICABLE IN CANADA, INCLUDING IN
THE PROVINCE OF QUEBEC.
POUR LES CLIENTS AUX ÉTATS-UNIS.
NON APPLICABLE AU CANADA, Y
COMPRIS LA PROVINCE DE QUÉBEC.
AUDIO POWER SPECIFICATIONS
CTA2006 Standard
Power Output: 20 Watts RMS × 4
at 4 Ohms < 1% THD+N
SN Ratio: 80 dBA
(reference: 1 Watt into 4 Ohms)
Tuner section
(N5200BT : US, CND)
FM
Tuning range: 87.5 MHz – 107.9 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
FM CCIR: -1,956.5 kHz to -487.3 kHz and
+500.0 kHz to +2,095.4 kHz
Usable sensitivity: 8 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 73 dB
Separation: 50 dB at 1 kHz
Frequency response: 20 Hz – 15,000 Hz
AM
Tuning range: 530 kHz – 1,710 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Sensitivity: 26 μV
(N5200BT : AEP, UK)
FM
Tuning range:
When [AREA] is set to [EUROPE]:
87.5 MHz – 108.0 MHz
When [AREA] is set to [RUSSIA]:
FM1/FM2: 87.5 MHz – 108.0 MHz
(at 50 kHz step)
FM3: 65 MHz – 74 MHz (at 30 kHz step)
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
When [AREA] is set to [EUROPE]:
FM CCIR: -1,956.5 kHz to -487.3 kHz and
+500.0 kHz to +2,095.4 kHz
When [AREA] is set to [RUSSIA]:
FM CCIR: -1,956.5 kHz to -487.3 kHz and
+500.0 kHz to +2,095.4 kHz
FM OIRT: -1,815.6 kHz to -943.7 kHz and
+996.6 kHz to +1,776.6 kHz
Usable sensitivity: 8 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 73 dB
Separation: 50 dB at 1 kHz
Frequency response: 20 Hz – 15,000 Hz
9-896-349-01
2016L33-1
Sony Video & Sound Products Inc.
©
2016.12
Photo: MEX-N5200BT
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
MW/LW
USB Player section
Tuning range:
Interface: USB (Full-speed)
MW: 531 kHz – 1,602 kHz
Maximum current: 1 A
LW: 153 kHz – 279 kHz
The maximum number of recognizable
Antenna (aerial) terminal:
External antenna (aerial) connector
–folders (albums): 256
Sensitivity: MW: 26 μV, LW: 50 μV
–files (tracks) per folder: 256
Compatible Android Open Accessory
(M71BT/N5200BT : E, AUS)
Corresponding codec:
FM
Tuning range:
87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 108.0 MHz (at 100 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)
FM tuning step:
50 kHz/100 kHz/200 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency:
FM CCIR: -1,956.5 kHz to -487.3 kHz and
+500.0 kHz to +2,095.4 kHz
Usable sensitivity: 8 dBf
Wireless Communication
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 73 dB
Communication System:
Separation: 50 dB at 1 kHz
Frequency response: 20 Hz – 15,000 Hz
Output:
AM
Tuning range:
531 – 1,602 kHz (at 9 kHz step)
Maximum communication range:
530 – 1,710 kHz (at 10 kHz step)
AM tuning step:
Frequency band:
9 kHz/10 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Modulation method: FHSS
Sensitivity: 26 μV
Compatible BLUETOOTH Profiles*
CD Player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 Hz – 20,000 Hz
Wow and flutter: Below measurable limit
The maximum number of: (CD-R/CD-RW
Corresponding codec:
only)
–folders (albums): 150 (including root
folder)
*1The actual range will vary depending on factors
–files (tracks) and folders: 300 (may less
than 300 if folder/file names contain many
characters)
–displayable characters for a folder/file
name: 32 (Joliet)/64 (Romeo)
*2BLUETOOTH standard profiles indicate the
Corresponding codec: MP3 (.mp3) and WMA
(.wma)
Canadian Model
Australian Model
MEX-N5100BT/N5150BT
MG-101CF-188
DAX-25A
Power amplifier section
Output: Speaker outputs
Speaker impedance: 4 Ω – 8 Ω
Maximum power output: 55 W × 4 (at 4 Ω)
tracks:
General
Outputs:
protocol (AOA): 2.0
MP3 (.mp3)
Bit rate: 8 kbps – 320 kbps (Supports
Inputs:
VBR (Variable Bit Rate))
Sampling rate: 16 kHz – 48 kHz
WMA (.wma)
Bit rate: 32 kbps – 192 kbps (Supports
VBR (Variable Bit Rate))
Sampling rate: 32 kHz, 44.1 kHz,
48 kHz
FLAC (.flac)
Power requirements: 12 V DC car battery
Bit depth: 16 bit, 24 bit
Sampling rate: 44.1 kHz, 48 kHz
Rated current consumption: 10 A
Dimensions:
BLUETOOTH Standard version 3.0
Mounting dimensions:
BLUETOOTH Standard Power Class 2
(Max. +4 dBm)
Mass: Approx. 1.2 kg (2 lb 11 oz)
Package contents:
Line of sight approx. 10 m (33 ft)*
1
2.4 GHz band
(2.4000 GHz – 2.4835 GHz)
2
:
A2DP (Advanced Audio Distribution
Profile) 1.3
Design and specifications are subject to
AVRCP (Audio Video Remote Control
change without notice.
Profile) 1.3
HFP (Handsfree Profile) 1.6
PBAP (Phone Book Access Profile)
SPP (Serial Port Profile)
SBC (.sbc), ACC (.m4a)
such as obstacles between devices, magnetic
fields around a microwave oven, static electricity,
reception sensitivity, antenna (aerial)'s
performance, operating system, software
application, etc.
purpose of BLUETOOTH communication between
devices.
US Model
AEP Model
UK Model
E Model
Audio outputs terminal:
FRONT, REAR, SUB
Power antenna (aerial)/Power amplifier
control terminal (REM OUT)
SiriusXM input terminal
(M71BT/N5200BT : US, CND only)
Remote controller input terminal
Antenna (aerial) input terminal
MIC input (terminal)
AUX input jack (stereo mini jack)
USB port
(negative ground (earth))
Approx. 178 mm × 50 mm × 177 mm
(7
1
/
in × 2 in × 7 in) (w/h/d)
8
Approx. 182 mm × 53 mm × 160 mm
(7
1
/
in × 2
1
/
in × 6
5
/
in) (w/h/d)
4
8
16
Main unit (1)
Remote commander (1): RM-X231
(M71BT/N5200BT : US, CND, E only)
Microphone (1)
Parts for installation and connections
(1 set)
AUDIO SYSTEM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MEX-M71BT and is the answer not in the manual?

Questions and answers

Summary of Contents for Sony MEX-M71BT

  • Page 1 +996.6 kHz to +1,776.6 kHz Usable sensitivity: 8 dBf Selectivity: 75 dB at 400 kHz Signal-to-noise ratio: 73 dB Separation: 50 dB at 1 kHz Frequency response: 20 Hz – 15,000 Hz 9-896-349-01 2016L33-1 Sony Video & Sound Products Inc. © 2016.12...
  • Page 2: Table Of Contents

    3-2. Mini Fuse (Blade Type) (FU1), Cover ......26 registered trademarks owned by Bluetooth list of conditions and the following SIG, Inc. and any use of such marks by Sony 3-3. Sub Panel Assy ..............26 disclaimer in the documentation and/or Corporation is under license.
  • Page 3: Section 1 Servicing Notes

    MEX-M71BT/N5200BT SECTION 1 SERVICING NOTES The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit. REPLACING THE LITHIUM BATTERY OF THE REMOTE NOTES ON HANDLING THE OPTICAL PICK-UP COMMANDER (M71BT/N5200BT: US, CND, E models)
  • Page 4: Model Identification

    [ b ] t [ B ] t [ENTER]. (Displayed characters/values in the following fi gure are ex- Model Number Label ample) Software main version XXXX MEX-M71BT and MEX-N5200BT (US, CND) : “1031” or higher MEX-N5200BT (AEP, UK, E, AUS) : “1030” or higher Part No. Destination 4-686-074-0[] N5200BT: US, CND models (UC) 3.
  • Page 5 Method of operation by remote commander (M71BT/N5200BT: US, CND, E models) Note: The model to which the remote commander is not attached can MEX-M71BT and MEX-N5200BT (US, CND) : “1031” or higher also be operated by using the remote commander. MEX-N5200BT (AEP, UK, E, AUS) : “1030”...
  • Page 6 MEX-M71BT/N5200BT NOTE OF REPLACING THE ANT001, CP001, IC001, IMPORTANT NOTE OF INITIALIZING IC602 AND IC1301 ON THE MAIN BOARD The purpose of “Bluetooth Initialize” is to initialize the Bluetooth ANT001, CP001, IC001, IC602 and IC1301 on the MAIN board connection history (HF/Audio Streaming). (To delete the device cannot replace with single.
  • Page 7 Bluetooth compatible smartphone or cellular phone 2. Search for the distance of this unit and the Bluetooth device • Bluetooth audio devices (SONY NWZ-A826, or select from (smartphone or cellular phone) about 5 m apart. connectable smartphone, cellular phones or audio devices list) Confi...
  • Page 8 MEX-M71BT/N5200BT BLUETOOTH INFORMATION WRITING METHOD 1. Installing the NFC Tag Data Writing Application for When the complete MAIN board, knob (VOL) assy (Ref. No. the Servicing NFC1) or front panel assy (Ref. No. FP1) is replaced, the writing Install the NFC Tag Data Writing Application on the smart- of Bluetooth information is necessary.
  • Page 9: Main Board (Component Side)

    MEX-M71BT/N5200BT • Checking the Version of the NFC Tag Data Writing 2. Writing the NFC Tag Data Application Write the NFC tag data (Bluetooth information) to the NFC mod- ule in the knob (VOL) assy (Ref. No. NFC1). Procedure: 1. Start the NFC Tag Data Writing Application on the smart- Procedure: phone.
  • Page 10 Software main version Bluetooth Local Name XXXX Bluetooth Device Addres MEX-M71BT and MEX-N5200BT (US, CND) : “1031” or higher MEX-N5200BT (AEP, UK, E, AUS) : “1030” or higher 2 In the state in which the software main version is displayed...
  • Page 11 MEX-M71BT/N5200BT 9. Check that “Completed!” is displayed on the screen of the 16. Check that “Completed!” is displayed on the screen of the smartphone. smartphone. Note 2: When “Completed!” is not displayed on the screen of the smart- Note 3: When “Completed!” is not displayed on the screen of the smart- phone, refer to “3.
  • Page 12 (Displayed characters/values in the following fi gure are example) Software main version XXXX MEX-M71BT and MEX-N5200BT (US, CND) : “1031” or higher MEX-N5200BT (AEP, UK, E, AUS) : “1030” or higher 2 In the state in which the software main version is displayed...
  • Page 13 MEX-M71BT/N5200BT 5. The Factor that One Touch Connection is Impossible The four following factors are considered as the factor that one touch connection is impossible. Guess and check the defective factor by each checking result. Note: The four following factors are examples.
  • Page 14 MEX-M71BT/N5200BT MEMO...
  • Page 15 MEX-M71BT/N5200BT • Please cut out along the dotted line and use it. Notice about the serial number change on the back side of Notice about the serial number change on the back side of the front panel: the front panel:...
  • Page 16 MEX-M71BT/N5200BT MEMO...
  • Page 17: General

    MEX-M71BT/N5200BT SECTION 2 This section is extracted GENERAL from operating instruction. (M71BT) Connection Connection/Installation Subwoofer* Cautions • Run all ground (earth) leads to a common ground (earth) point. • Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing).
  • Page 18: Installation

    You may not be able to install this unit in dashboard or the cutout hole on some makes of Japanese cars. In such a boat case, consult your Sony dealer. Removing the protection collar • Before installing, make sure the catches on and the bracket...
  • Page 19 MEX-M71BT/N5200BT (N5200BT: US, CND) Connection (For MEX-N5200BT) Connection/Installation Subwoofer* Cautions • Run all ground (earth) leads to a common ground (earth) point. • Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing).
  • Page 20 You may not be able to install this unit in When using the steering wheel remote some makes of Japanese cars. In such a case, consult your Sony dealer. control Removing the protection collar Installation of the connection cable RC-SR1 TOYOTA (not supplied) is required before use.
  • Page 21 MEX-M71BT/N5200BT (N5200BT: AEP, UK) Connection (For MEX-N5200BT) Connection/Installation Subwoofer* Cautions • Run all ground (earth) leads to a common ground (earth) point. • Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing).
  • Page 22 If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.
  • Page 23 MEX-M71BT/N5200BT (N5200BT: E, AUS) Connection (For MEX-N5200BT) Connection/Installation Subwoofer* Cautions • Run all ground (earth) leads to a common ground (earth) point. • Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing).
  • Page 24 Using the wired remote control Installation You may not be able to install this unit in When using the steering wheel remote some makes of Japanese cars. In such a case, consult your Sony dealer. control (AUS only) (AUS only) Removing the protection collar...
  • Page 25: Disassembly

    MEX-M71BT/N5200BT SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW FRONT PANEL SECTION 3-6. SERVICE POSITION Note: Illustration of disassembly is omitted. (Page 29) 3-2. MINI FUSE (BLADE TYPE) (FU1), COVER (Page 26) 3-3.
  • Page 26: Mini Fuse (Blade Type) (Fu1), Cover

    Note: Follow the disassembly procedure in the numerical order given. 3-2. MINI FUSE (BLADE TYPE) (FU1), COVER Note 1: For the MEX-M71BT, a cover sheet is attached to the cover. Remove the cover block without peeling off the cover sheet. The illustration depicts the MEX-N5200BT.
  • Page 27: Cd Mechanism Deck (Mg-101Cf-188)

    MEX-M71BT/N5200BT 3-4. CD MECHANISM DECK (MG-101CF-188) Note 1: The service manual of the mechanism deck, used in this mod- el has been issued in a separate volume. Please refer to the service manual of the MG-101 series for the mechanism deck information.
  • Page 28: Main Board

    MEX-M71BT/N5200BT 3-5. MAIN BOARD Note 1: When the MAIN board is replaced, it is necessary to replace knob (VOL) assy (Ref. No. NFC1) simultaneously. Also, the destination setting, Blue- tooth operation check and Bluetooth information writing is necessary. Re- fer to “DESTINATION SETTING METHOD” on page 4, “BLUETOOTH FUNCTION CHECKING METHOD USING A SMARTPHONE OR CEL- LULAR PHONE”...
  • Page 29: Service Position

    MEX-M71BT/N5200BT 3-6. SERVICE POSITION Note 1: The service position below cannot be performed with the fl exible fl at cable (length: 90 mm) used with the unit. Refer to “FLEXIBLE FLAT CABLE FOR THE MECHANISM DECK CONNECTION” on page 6, and use a long fl exible fl...
  • Page 30: Test Mode

    MEX-M71BT/N5200BT SECTION 4 TEST MODE SETTING THE TEST MODE Setting method: 1. In the state of source off (the clock is displayed on the liquid crystal display), enter the test mode by pressing the buttons in order of the [ 4] t [MIC 5] t [ V ALBUM 1] (press only the [ V ALBUM 1] button for two seconds).
  • Page 31: Diagrams

    MEX-M71BT/N5200BT SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM - MAIN Section - CD MECHANISM DECK BLOCK (MG-101CF-188) 5 AIN RFOUT 1 EFMIN DATA 60 DATA DACOUTL 99 LVRIN 59 BCK 7 BIN LRCK 58 LACK DACOUTS 10 SWIN 6 CIN MCLK...
  • Page 32: Block Diagram - Audio Output/Panel/Power Supply Section

    MEX-M71BT/N5200BT 5-2. BLOCK DIAGRAM - AUDIO OUTPUT/PANEL/POWER SUPPLY Section - SYSTEM CONTROLLER IC501 (2/2) VDD_3.3V CENTER VOLTAGE ILL_B GENERATOR IC402 (1/2) J401 PLL-UP SWITCH 70 REMOTE_1K FL, FR, SUB LINE AMP >001B Q1307, 1308 IC401 FRONT R-CH J1001 (2/2) 81 RC_IN1...
  • Page 33 MEX-M71BT/N5200BT THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Waveforms (In addition to this, the necessary note is printed in each block.) – MAIN Board – For Printed Wiring Boards. For Schematic Diagrams. IC1305 2 (RFOUT)
  • Page 34: Printed Wiring Boards - Main Section (1/2)

    MEX-M71BT/N5200BT 5-3. PRINTED WIRING BOARDS - MAIN Section (1/2) - • : Uses unleaded solder. MAIN BOARD (COMPONENT SIDE) D400 R400 C305 C321 C206 R1606 IC400 IC401 R467 R408 Q403 Q405 Q406 Q404 R411 (M71BT/N5200BT: US, CND) C443 C436 C444...
  • Page 35: Printed Wiring Boards - Main Section (2/2)

    MEX-M71BT/N5200BT 5-4. PRINTED WIRING BOARDS - MAIN Section (2/2) - • : Uses unleaded solder. MAIN BOARD (CONDUCTOR SIDE) J401 ( M71BT/N5200BT: US, CND ) FRONT (FRONT VIEW) (M71BT/N5200BT: US, CND, E, AUS) CN301 REAR J1001 REAR LCH (+) REMOTE...
  • Page 36: Schematic Diagram - Main Section (1/4)

    MEX-M71BT/N5200BT 5-5. SCHEMATIC DIAGRAM - MAIN Section (1/4) - • See page 33 for Waveforms. • See page 40 for IC Block Diagrams. • See page 41 for IC Pin Function Description. MAIN BOARD (1/4) >001S R536 R539 C725 C753...
  • Page 37: Schematic Diagram - Main Section (2/4)

    MEX-M71BT/N5200BT 5-6. SCHEMATIC DIAGRAM - MAIN Section (2/4) - • See page 33 for Waveforms. • See page 40 for IC Block Diagrams. • See page 41 for IC Pin Function Description. MAIN BOARD (2/4) >005S MAIN BOARD (3/4) (Page 38) R1589 >001S...
  • Page 38: Schematic Diagram - Main Section (3/4)

    MEX-M71BT/N5200BT 5-7. SCHEMATIC DIAGRAM - MAIN Section (3/4) - • See page 33 for Waveforms. • See page 40 for IC Block Diagrams. J401 FRONT J1001 (ANTENNA IN) REAR REMOTE MAIN BOARD (3/4) R1606 FB1005 FB1006 IC201 IC002 Q403 Q404...
  • Page 39: Schematic Diagram - Main Section (4/4)

    MEX-M71BT/N5200BT 5-8. SCHEMATIC DIAGRAM - MAIN Section (4/4) - • See page 40 for IC Block Diagrams. (M71BT/N5200BT: US, CND, E, AUS) MAIN BOARD (4/4) IC304 REAR RCH (+) CN301 REAR LCH (+) POWER AMP RR_P IC304 REAR RCH (–)
  • Page 40 MEX-M71BT/N5200BT • IC Block Diagrams – MAIN Board – IC001 SDP2014HN/V102 IC201 LV56851UV-XH ALL OUTPUT OFF EXCEPT VDD ALL OUTPUT OFF 32 31 27 26 VREF VREG 5.1V UVDET OVDET VREF 1.25V VDDA_IFADC 1 DIGITAL CONTROL DIGITAL XTAL BDET VSSA_IFADC 2...
  • Page 41 MEX-M71BT/N5200BT • IC Pin Function Description MAIN BOARD IC501 LC88FC3K0AF2329-ENG (SYSTEM CONTROLLER) (N5200BT: AEP, UK, E, AUS) LC88FC3K0AF2330-ENG (SYSTEM CONTROLLER) (M71BT/N5200BT: US, CND) Pin No. Pin Name Description 1 to 3 Not used FLASH_RW Debug communication terminal Not used System reset signal input terminal “L”: reset...
  • Page 42 MEX-M71BT/N5200BT Pin No. Pin Name Description OFFSET_DET (NC) Not used KEY_ACK0 Key acknowledge signal (wake up signal) input from the rotary commander KEY_ACK1 Key acknowledge signal (wake up signal) input from the front panel block SIRCS Remote control signal input from the front panel block...
  • Page 43 MEX-M71BT/N5200BT MAIN BOARD IC601 LC786823E-6E11-3H (USB CONTROLLER, INPUT SELECTOR, AUDIO DSP, ELECTRICAL VOLUME) Pin No. Pin Name Description Not used AVDD1 Power supply terminal (+3.3V) (for analog system) AVSS1 Ground terminal (for analog system) External capacitor connection terminal for audio D/A converter and electrical volume reference...
  • Page 44 MEX-M71BT/N5200BT Pin No. Pin Name Description SIFDO Serial data output to the system controller SIFCE Chip enable signal input from the system controller BUSYB Busy signal output to the system controller “L”: busy CD_BUSYB Busy signal input from the digital servo processor “L”: busy...
  • Page 45 MEX-M71BT/N5200BT MAIN BOARD IC1305 LC78615E-01US-H (RF AMP, DIGITAL SERVO PROCESSOR) Pin No. Pin Name Description EFMIN RF signal input terminal RFOUT RF signal output terminal External low-pass fi lter capacitor connection terminal for DC level detection of RF signal PHLPF External low-pass fi...
  • Page 46: Exploded Views

    MEX-M71BT/N5200BT SECTION 6 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • The mechanical parts with no reference they may have some difference from the number in the exploded views are not sup- original one. plied. • Items marked “*” are not stocked since •...
  • Page 47: Chassis Section

    MEX-M71BT/N5200BT 6-2. CHASSIS SECTION (M71BT/N5200BT: US, CND) MAIN board not supplied not supplied not supplied Note: When the complete MAIN board (Ref. No. 52) is replaced, it is necessary to replace knob (VOL) assy (Ref. No. NFC1: page 46) simultaneously. Also, the destination setting, Bluetooth operation check and Bluetooth information writ- ing is necessary.
  • Page 48: Electrical Parts List

    MEX-M71BT/N5200BT SECTION 7 MAIN ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • CAPACITORS When indicating parts by reference num- the parts list may be different from the uF: μF ber, please include the board name. parts specifi ed in the diagrams or the com- •...
  • Page 49 MEX-M71BT/N5200BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C326 1-116-733-11 CERAMIC CHIP 1uF C623 1-118-386-11 CERAMIC CHIP 0.1uF C350 1-118-997-11 ELECT 3300uF C624 1-164-858-11 CERAMIC CHIP 22PF C625 1-116-724-11 CERAMIC CHIP 4.7uF 6.3V C400...
  • Page 50 MEX-M71BT/N5200BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C1005 1-116-707-11 CERAMIC CHIP 47uF < BT MODULE > C1006 1-118-386-11 CERAMIC CHIP 0.1uF C1008 1-118-040-11 CERAMIC CHIP 2.2uF CP001 (Not supplied) BT MODULE (WB113CX) (See Note)
  • Page 51 MEX-M71BT/N5200BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC400 6-721-638-01 IC NJM8065RB1-TE1 1-218-941-81 METAL CHIP 1/16W 1-218-965-11 METAL CHIP 1/16W IC401 6-721-638-01 IC NJM8065RB1-TE1 IC402 6-721-638-01 IC NJM8065RB1-TE1 1-218-965-11 METAL CHIP 1/16W IC403 6-712-391-01...
  • Page 52 MEX-M71BT/N5200BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R426 1-218-990-81 SHORT CHIP 0 (N5200BT: AEP, UK, E, AUS) R528 1-218-941-81 METAL CHIP 1/16W R427 1-216-797-11 METAL CHIP 1/10W R529 1-218-941-81 METAL CHIP 1/16W R428...
  • Page 53 MEX-M71BT/N5200BT MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R714 1-218-949-11 METAL CHIP 1/16W R1403 1-216-864-91 SHORT CHIP R715 1-218-975-11 METAL CHIP 1/16W R1428 1-218-990-81 SHORT CHIP R716 1-218-951-11 METAL CHIP 1/16W R1429 1-218-990-81 SHORT CHIP...
  • Page 54 MEX-M71BT/N5200BT Ref. No. Part No. Description Remark 1-846-033-11 CONNECTION CABLE (ISO) (Power supply connection cable) (N5200BT: AEP, UK) 1-846-979-11 CONNECTION CABLE, AUTOMOBILE (Power supply connection cable) (M71BT/N5200BT: US, CND, E, AUS) RELEASE KEY ************************************************************* BRACKET (N5200BT: AEP, UK) ACCESSORIES ************...
  • Page 55 MEX-M71BT/N5200BT MEMO...
  • Page 56 MEX-M71BT/N5200BT REVISION HISTORY Ver. Date Description of Revision 2016.12 How to search for a contact point of signal lines or the like in DIAGRAMS SECTION If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use the PDF fi...

This manual is also suitable for:

Mex-n5200bt

Table of Contents