Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Polon-Alfa EKS-3022
Summary of Contents for Polon-Alfa EKS-3022
- Page 1 IK-E398-001-GB Edition I , 03.2023 POLON 3000 FIRE ALARM SYSTEM CONTROL and MONITORING ELEMENT TYPE EKS-3022 Installation and Maintenance Manual IK-E398-001-GB Edition I __________________________________________________________________________________ EKS-3022 CONTROL ELEMENT...
- Page 2 IK-E398-001-GB Edition I, 03.2023 The EKS-3022 control element, which i the subject of this Manual, meets the essential requirements of the following regulations of the European Parliament and of the Council (EU) and European Union directives: CPR/305/2011 Regulation (EU) of the European Parliament and of the Council of 9 March 2011 laying down harmonised conditions for the marketing of consumer products repealing Council Directive 89/106/EEC;...
-
Page 3: Table Of Contents
Repairs and maintenance....................... 14 8.2. Works at height ........................14 8.3. Anti-dusting eye protection ....................14 8.4. Protection against electric shock ................... 14 Storage and transport ....................14 9.1. Storage ........................... 14 9.2. Transport ..........................14 __________________________________________________________________________________ EKS-3022 CONTROL ELEMENT... -
Page 4: Purpose
- monitoring of the above mentioned devices, - monitoring of equipment condition. EKS-3022 control and monitoring element is intended for use in addressable detection lines of the POLON 3000 fire alarm control panel. The element is designed for indoor and outdoor operation. -
Page 5: Technical Specifications
Operating Temperature -40 °C to +85 °C Climate category 40/085/04 Permissible relative humidity up to 95 % at 40 °C Electrical strength of insulation 1500 V Ingress protection IP 66 Enclosure material and colour Polycarbonate (PC), Grey __________________________________________________________________________________ EKS-3022 CONTROL ELEMENT... -
Page 6: Design Description
IK-E398-001-GB Edition I, 03.2023 3. Design description The EKS-3022 control and monitoring element is made in the form of a printed circuit board with electronic components and a set of connectors, that has been put inside an enclosure. The enclosure has wall mounting holes located in the corners. -
Page 7: Principles Of Operation
The relay contacts are also returned to their initial position on command from the control panel. The EKS-3022 control and monitoring element transfers the following states to the control panel: writing the address,... - Page 8 3 V. The same rules apply to IN HV inputs. If the IN HV outputs or inputs are not used, the position of corresponding jumpers is not relevant If the outputs are not used, the position of the corresponding jumpers is not relevant. __________________________________________________________________________________ EKS-3022 CONTROL and MONITORING ELEMENT...
-
Page 9: Control And Monitoring Element Operating Modes
Control output safe state: Yes (triggered, untriggered) No (no change) d) Continuity monitoring of the cable connected to the control output – (Yes, No) e) Group number - (0 ÷ 65535) f) Number of cycles (0 ÷ 255) __________________________________________________________________________________ EKS-3022 CONTROL ELEMENT... - Page 10 Reset time - T T ow Definite cyclic Triggering mode Trigger delay time - T Trigger time - T Reset time - T Number of cycles - L L c = 3 T ow __________________________________________________________________________________ EKS-3022 CONTROL and MONITORING ELEMENT...
-
Page 11: Maintenance And Operation
(available for purchase at POLON-ALFA). Connect the wires as described on the connectors. Functions of individual EKS-3022 terminals are located on the top cover of the enclosure as shown in the Figure 7.. Connect the detection line shields to the fields marked SHLD. - Page 12 IK-E398-001-GB Edition I, 03.2023 Figure 7.1 EKS-3022 connection diagram __________________________________________________________________________________ EKS-3022 CONTROL and MONITORING ELEMENT...
- Page 13 IK-E398-001-GB Edition I , 03.2023 Figure 7.2 EKS-3022 Enclosure Cover with Terminal Functions __________________________________________________________________________________ EKS-3022 CONTROL ELEMENT...
-
Page 14: Safety Conditions
9.1. Storage The EKS-3022 control elements should be stored in enclosed spaces where no caustic vapours and gases are present, with the temperature between 0 °C to +40 °C, and the relative humidity not exceeding 80 % at a temperature of +35 °C. - Page 15 IK-E398-001-GB Edition I , 03.2023 __________________________________________________________________________________ EKS-3022 CONTROL ELEMENT...
Need help?
Do you have a question about the EKS-3022 and is the answer not in the manual?
Questions and answers