Download
Share
Print this page
  1. Manuals
  2. Brands
  3. BILT HARD Manuals
  4. Chipper
  5. TL-G-WS7
  6. Operator's manual

BILT HARD TL-G-WS7 Operator's Manual

Wood chipper
Hide thumbs

Advertisement

Quick Links

Download this manual
TL-G-WS7

Advertisement

loading
Need help?

Need help?

Do you have a question about the TL-G-WS7 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for BILT HARD TL-G-WS7

Summary of Contents for BILT HARD TL-G-WS7

  • Page 1 TL-G-WS7...
  • Page 2 Chipper-shredder Specifications TL-G-WS7 7.6"x2.9"/ Ø3" 9.7"x14.1"/ Ø5.6" 29.1"x19.1"x25.2" Fuel Specifications Use regular unleaded gasoline with a minimum octane rating of 87 and an ethanol content of less than 10% by volume. DO NOT USE E15 or E85. DO NOT OVERFILL.
  • Page 3 Important Message About Temperature Your product is designed and rated for continuous operation at ambient temperatures up to 104°F (40°C). When your product is needed it may be operated at temperatures ranging from 5°F (-15°C) to 122° F (50°C) for short periods of time. If exposed to temperatures outside this range during storage, it should be brought back within this range before operation.
  • Page 8 1.Right Heightening Plate 7.Support Plate 2.Hopper 8.Discharge Bag 3.Left Heightening Plate 9.Discharge Port Cover 4.Engine 10.Operator’ s Manual 5.Chipper Chute 11.Wheels 6.Baffle Install the Wheel：Put a wheel and flat washer (ø15xø25x2) on each end of the axle, then screw M8x12 small head bolts into both sides of the axle to secure wheels in place.
  • Page 9 Chipper Chute Install the Chipper Chute: Position the chipper chute over the three threaded studs protruding from the fixed plate, and M6x55(x1) attach using three M10 nuts to lock the chipper chute. M6 X 55 1. Install the Hopper: Put the hopper into the lower cover and align with the mounting hole, then secure the hopper with four M6x15 bolts.
  • Page 10 1. Combine the left heightening plate and baffle: align with mounting holes; Insert four M5x12 bolts into the mounting hole from the outside of the left heightening plate and tighten them with four M5 nuts; Fix the baffle on the left heightening plate. 2.
  • Page 14 To shut down the machine,turn the engine switch to the OFF position,and it will gradually come to a standstill.
  • Page 15 Place the spark plug wire back.

  • Page 16: Engine Maintenance

    Engine Maintenance NOTICE To prevent accidental starting, remove and Once oil has been added, a visual check ground spark plug wire before performing should show oil about 1-2 threads from any service. running out of the fill hole. If using the Changing the Engine Oil dipstick to check oil level, DO NOT screw in Change oil when the engine is warm.
  • Page 17 5. Refer to the spark plug section on the Specifications page when replacing the plug. 6. Carefully thread the plug into the engine. 7. Use a spark plug socket (not included) to firmly install the plug. 8. Attach the spark plug wire to the plug. Clean the Air Filter 1.
  • Page 22 No. Description Q'ty No. Description Q'ty Engine, 224cc Washer, Ø8 Junction Plate Assembly, Engine Impeller Assembly, Black Flat Key, 6.3 x 6.3 x 50 Shredder Blade Washer Lock Nut, M8 Lock Washer, Ø12 Flange Bolt, M8 x 40 Washer, Ø12 Support Mount Assembly, Black Tube Support, Black Screw, 7/16 - 20UNF...