Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for BILT HARD TRA-0401
Summary of Contents for BILT HARD TRA-0401
- Page 1 TRA-0401...
- Page 2 Chipper-shredder Specifications TRA-0401 Hooper Capacity 0.5" 7.6"x2.9"/ Ø3" 9.7"x14.1"/ Ø5.6" 29.1"x19.1"x25.2" Engine Parts Schedule Fuel Specifications Use regular unleaded gasoline with a minimum octane rating of 87 and an ethanol content of less than 10% by volume. DO NOT USE E15 or E85. DO NOT OVERFILL.
- Page 3 Important Message About Temperature Your product is designed and rated for continuous operation at ambient temperatures up to 104°F (40°C). When your product is needed it may be operated at temperatures ranging from 5°F (-15°C) to 122° F (50°C) for short periods of time. In any event, the product must always be operated outdoors, in a well-ventilated area and away from doors, windows and vents.
- Page 4 Make sure to read and understand all the instructions and safety precautions as outlined in the manual . Do not attempt to operate the machine until you fully understand how to properly operate and maintain the engine and how to avoid accidental injuries and/or property damage.
- Page 5 Never overfill the fuel tank. Fill the tank to no more than 1cm below the bottom of the filler neck to provide space for expansion as the heat of the engine can cause fuel to expand.
- Page 6 NOTE:Wet material is easy to block the machine, so please do not put in. Avoid feeding pine needles,flax and cabbage tree leaves into the machine; these stringy materials can wrap around the rotor shaft and work their way into the bearing. Allow time for the machine to reach the highest spinning revolutions before feeding the next load of...
- Page 8 1.Right Heightening Plate 7.Support Plate 2.Hopper 8.Discharge Bag 3.Left Heightening Plate 9.Discharge Port Cover 4.Engine 10.Operator’s Manual 5.Chipper Chute 11.Wheels 6.Baffle 600ml 1. Install the Wheel: Thread the 2 wheels on the wheel shaft and screw the M8x12 bolt and washer(A) into the wheel shaft end to secure the wheels in place.
- Page 9 M8 X 12 M6x55(x1) Chipper Chute Install the Chipper Chute: Position the chipper chute over the three threaded studs protruding from the fixed plate, and attach using three M10 nuts(B) nuts to lock the chipper chute. M6 X 55 1. Install the Hopper: Put the hopper into the lower cover and align with the mounting hole, then secure the hopper with four M6x12 bolts(D)
- Page 10 1. Combine the left heightening plate and baffle: align with mounting holes;Insert four M5x12 bolts(G) into the mounting hole from the outside of the left heightening plate and tighten them with four M5 nuts: Fix the baffle on the left heightening plate.
- Page 11 Chipper Chute...
- Page 12 Material maximum diameter 0.5inch(1.3cm). Chipper Chute Chipper Chute DO NOT attempt to crank or start the engine before it has been properly filled with the recommended chipper chute type and amount of oil. Damage to the wood chipper as a result of failure to follow these instructions will void your warranty.
- Page 13 Our engines work well with 10% or less The engine is equipped with a low oil ethanol blend fuels. When using blended shut-o ffand will stop when the oil level in the crankcase falls below the fuels there are some issues worth noting: threshold level.
- Page 14 As a load passes through the Chute cutting disc and is discharged,the engine speed may decrease. Allow enough time for the engine to accelerate to the highest RPM before another load is added. 0.5inch intothe top of the Feed Hopper. The material is then pulled into the cutting chamber by airflow Chipper Chute...
- Page 15 To shut down the machine,turn the engine switch to the OFF position, and it will gradually come to a standstill. Place the spark plug wire back. CHOKE Remove the engine's spark plug.
-
Page 16: Engine Maintenance
Engine Maintenance NOTICE To prevent accidental starting, remove and If using the dipstick to check oil level, DO ground spark plug wire before performing NOT screw in the dipstick while checking. any service. Changing the Engine Oil WARNING Change oil when the engine is warm. Refer to Used oil is a hazardous waste product and the oil specification to select the proper grade for your operating... - Page 17 5. Refer to the spark plug section on the Specifications page when replacing the plug. 6. Carefully thread the plug into the engine. 7. Use a spark plug socket (not included) to firmly install the plug. 8. Attach the spark plug wire to the plug. Clean the Air Filter 1.
- Page 23 ENGINE PARTS SCHEDULE...
-
Page 24: Engine Parts List
Engine Parts List... - Page 25 Engine Parts List...
Need help?
Do you have a question about the TRA-0401 and is the answer not in the manual?
Questions and answers