Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Labtron TP-K10
Summary of Contents for Labtron TP-K10
- Page 1 Mullen burst tester TP-K10 TP-K10 www.labtron.com info@labtron.com...
-
Page 2: Table Of Contents
Mullen burst tester TP-K10 Index Sr.no Title Page no Introduction Features Specifications Applications Instrument Introduction Installation Operations Maintenance Troubleshooting... -
Page 3: Introduction
Mullen burst tester TP-K10 Introduction Mullen burst tester TP-K10 is used to measure the bursting strength of paper submitted to increasing hydraulic pressure. Used in testing bursting strength of all types of papers in the 0 to 5600 kPa range depending on clamp pressure. It has mechanically &... -
Page 4: Specifications
Mullen burst tester TP-K10 Specifications Model No. TP-K10 Measurement range 0 to 5600 kPa Accuracy ± 0.5 % F.S. Compression speed 170 ± 15 ml/min Clamp pressure ≥ 690 kPa Diameter of upper clamp 31.5 ± 0.05 mm Diameter of lower clamp 31.5 ±... -
Page 5: Instrument Introduction
Mullen burst tester TP-K10 Instrument Introduction Equipment descriptions Power Switch Located in front of the instrument, used to control the power supply, the green light indicates power on, off the light indicates power off. Operation Keys The instrument operation control system is centrally arranged on the operation panel. The operation keys are arranged as shown in the figure below. - Page 6 Mullen burst tester TP-K10 Button response when testing the interface: The upper right corner shows the current running status; Button "Test": perform the test; Button "Stop" : Click this button to end the test during the test; Button "return to zero": return the force and maximum force equivalent to zero;...
-
Page 7: Installation
Mullen burst tester TP-K10 Installation a. Open the upper cover of the instrument packing box and take out the technical documents and accessories (wrench, silicone oil, rubber film, gas pipe, power cord). b. Remove the surrounding box plates, remove the bolts, fix the instrument on... -
Page 8: Operations
Mullen burst tester TP-K10 Operations Trial Machine • Connect one end of the randomly equipped air intake pipe to the air source and insert the other end into the air intake joint on the right side of the fuselage. • Turn on the power switch and preheat for 30 minutes with power on. - Page 9 Mullen burst tester TP-K10 Testing • Connect the power cable and start the machine (the power switch is located behind the machine, and the red light indicates the machine is started). • Press "Setting" to complete the test setting in it. Generally, it only needs to change the unit.
- Page 10 Mullen burst tester TP-K10 Pin printers Loading roll and paper Step 1: Press the round button to open the front cover of the printer; Take out the remaining paper core, as shown below: Step 2: Put in a new roll of paper, as shown below...
-
Page 11: Maintenance
Mullen burst tester TP-K10 Maintenance 8.1 General maintenance items The operator should read the instruction manual thoroughly, strictly abide by the operating procedures, and do the following maintenance work: 8.1.1. Keeping the instrument clean and dustproof should be added when not used for a long time. - Page 12 Mullen burst tester TP-K10 8.3.2. Description of each button: Release: click to release pressure, only after the boot meets the release limit can run and click release pressure. Compress: click to add pressure, only when the boot meets the release limit can run and click add pressure.
- Page 13 Mullen burst tester TP-K10 8.3.8. Press the "cylinder" key, the upper-pressure disc will compress the lower-pressure disc in 1 second. (At this time, the upper-pressure plate is in the state of pressing the lower- pressure plate) 8.3.9. After the upper-pressure plate compacts the lower-pressure plate, tighten the lower- pressure plate with a wrench (be sure to tighten);...
- Page 14 Mullen burst tester TP-K10 calibration coefficient, fill the result into the force calibration coefficient again, and then click Set to exit). 2. After selecting the channel to be calibrated in the upper left corner, the first step must be to calibrate the "zero point". Firstly, click the "Clear" button to clear the data in the calibration data table, then click the "Force return to zero"...
-
Page 15: Troubleshooting
Mullen burst tester TP-K10 Troubleshooting 9.1 The cardboard cannot be broken • The common cause of this problem is that the oil cup is not tightened or there is air in the oil cylinder. • The solution is to loosen the nut of the oil cup and press down firmly on the rubber film with your fingers several times to drain the air from the oil cup.
Need help?
Do you have a question about the TP-K10 and is the answer not in the manual?
Questions and answers