Download
Share
Print this page
TP-Link TD-W8950ND Quick Installation Manual
  1. Manuals
  2. Brands
  3. TP-Link Manuals
  4. Network Router
  5. TD-W8950ND
  6. Quick installation manual
TP-Link TD-W8950ND Quick Installation Manual

TP-Link TD-W8950ND Quick Installation Manual

Quick installation guide
Hide thumbs Also See for TD-W8950ND:

Advertisement

Quick Links

Download this manual See also: User Manual
Note
Please use only wired network connections to configure the Router.
Power down all of your network devices, including your computer(s) and the
Modem Router. If you currently use a modem, disconnect it now - the Modem
Router will replace your current modem.
Connect your computer to the
LAN port on the Modem Router
with an Ethernet cable.
Connect the splitter to the wall
jack using a telephone line, then
use the other telephone line to
directly connect it to the LINE port
of the Modem Router and the
MODEM port of the splitter, also
have the PHONE port of the
splitter connected to a telephone.
If no telephone is needed, please connect the LINE port of the Modem Router
Note
to the wall jack using the telephone line directly.
1

Advertisement

loading

Related Manuals for TP-Link TD-W8950ND

Summary of Contents for TP-Link TD-W8950ND

  • Page 1 Note Please use only wired network connections to configure the Router. Power down all of your network devices, including your computer(s) and the Modem Router. If you currently use a modem, disconnect it now - the Modem Router will replace your current modem. Connect your computer to the LAN port on the Modem Router with an Ethernet cable.
  • Page 2 LED turns off after flashing, please contact your ISP to ensure that your internet connection is active. Note To configure the device, you can either run the setup CD-ROM (method one), or run the Web based Quick Setup Wizard (method two). TP-LINK strongly recommends that you run the setup CD-ROM.
  • Page 3 Insert the provided Resource CD into your CD-ROM drive. The Setup Wizard will automatically pop up on your computer’s screen. Please select your product model and click Start Setup Then a flash video will pop up and show you how to connect your devices.
  • Page 4 Login Open your web browser and type 192.168.1.1 address bar and press Enter A dialog box will prompt you for the User name and Password. Enter the default values and click OK. User name: admin Password: admin Click OK If the dialog box does not pop up, please refer to T3 in the Troubleshooting Note guide.
  • Page 5 Internet Parameters Configuration This page will then display. Enter the VPI and VCI values given by your ISP Click Next If you did not get the VPI, VCI and WAN Link Type information, please Note contact your ISP for this information. Choose the Connection Type given by your ISP.
  • Page 6 This page will then display Enter the Username and Password given by your ISP. Click Next Click Next If you did not get the PPP Username or PPP Password, please contact your Note ISP for this information. The configuration for PPPoA is similar to that of PPPoE. Note After completing the above configuration, please proceed to Wireless...
  • Page 7 Click Next After completing the above configuration, please proceed to Wireless Configuration. Configuration For IPoA Manually enter address, Subnet Mask, default gateway and DNS server addresses provided by your ISP Click Next Click Next If you did not get the IP Address, Subnet Mask and DNS addresses, please Note contact your ISP for this information.

  • Page 8: Wireless Configuration

    Configuration For Bridge Mode Click Next After completing the above configuration, please proceed to Wireless Configuration. Wireless Configuration Create a unique and easy to remember name your wireless network. You can also keep the default setting without the device being affected Click Next The wireless security is Disabled by default.

  • Page 9: Wan Setup - Summary

    Modem Router while it’s rebooting. The basic settings for your Router are completed. Please open the web browser and log on to the following websites: http://www.tp-link.com http://www.google.com If the above websites can be accessed, it indicates that your Router has been configured successfully and you can start to enjoy the Internet.
  • Page 10 T1. How do I restore my Router’s configuration to its factory default settings? With the Router powered on, press and hold the Reset button on the rear panel for 8 to 10 seconds before releasing it. Press it for 8 to 10 seconds Once the Router is reset, the current configuration settings will be lost and Note you will need to re-configure the Router.
  • Page 11 Click Network Connections Right-click Local Area Connection Click Properties Double-click Internet Protocol (TCP/IP)
  • Page 12 Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK Click OK...
  • Page 13 For Windows Vista OS Go to Start > Settings > Control Panel, and then you will see the following page. Click View network status and tasks Click View status Click Properties...
  • Page 14 Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK...
  • Page 15 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured.
  • Page 16 Router by following the instructions of this QIG. Please feel free to contact our Technical Support if the problem still exists. For more details about Troubleshooting and Technical Support contact Note information, please Technical Support Website: http://www.tp-link.com/support/Support.asp...

  • Page 17: Technical Support

    Global Australia & New Zealand Tel: +86 755 26504400 Tel: AU 1300 87 5465 E-mail : support@tp-link.com NZ 0800 87 5465 Service time:24hrs, 7days a week E-mail: support@tp-link.com.au Service time: Monday to Friday 9:00 AM to 9:00 PM AEST...