Harley Benton Spaceship Power 50M-B Quick Start Manual

Spaceship Power 50M-B
Safety instructions
Intended use
This device is designed to hold, secure and power multiple series-connected effects
pedals for musical instruments. Use the device only as described in this user manual.
Any other use or use under other operating conditions is considered to be improper
and may result in personal injury or property damage. No liability will be assumed for
damage resulting from improper use.
This device may be used only by persons with sufficient physical, sensory, and intel-
lectual abilities and the necessary knowledge and experience. Other persons may use
this device only if they are supervised or instructed by a person who is responsible
for their safety.
Risk of injury and choking hazard for children!
Children can suffocate on packaging material and small parts. Children can
injure themselves when handling the device. Never allow children to play
with the packaging material and the device. Always store packaging mate-
rial out of the reach of babies and small children. Always dispose of pack-
aging material properly when it is not in use. Never allow children to use
the device without supervision. Keep small parts away from children and
make sure that the device does not shed any small parts (such as knobs)
that children could play with.
Incorrect handling of lithium batteries can result in injury!
In the event of a short circuit, overheating or mechanical damage, lithium
batteries can cause severe injuries. Handle lithium batteries in a correct
and professional manner. Store lithium batteries in a cool and dry place in
their original packaging. Keep lithium batteries away from sources of heat.
Never open lithium batteries. Only charge rechargeable lithium batteries
with a suitable charger. Remove the lithium batteries before disposing of
the device. Cover the poles of used lithium batteries with adhesive tape to
prevent short circuits. Electrolyte can escape from damaged lithium bat-
teries. Put the damaged lithium battery in air-tight packaging. Collect the
electrolyte with absorbent paper. Wear rubber gloves while doing so.
Possible damage due to leaking batteries!
Batteries can leak and cause permanent damage to the device. Remove
the batteries from the device if you are not planning to use it for an extend-
ed period of time.
Risk of fire due to incorrect polarity!
Incorrectly inserted batteries may cause fires and destroy the device and
the batteries. Observe the markings on the batteries and on the device.
Ensure that proper polarity is observed when inserting batteries.
Features
• Light and compact pedal board
• Battery or mains powered
• Powder-coated aluminium frame
• 7 × isolated filtered outputs with short-circuit protection eliminate noise
and humming
• 4 × non-isolated outputs for multi effects units or for charging smartphones
and tablets
Scope of delivery
• 3 × DC cable, each 30 cm long
• 3 × DC cable, each 60 cm long
• 3 × DC cable, each 90 cm long
• 1 × cable with reversed polarity and red plug
• 1 × battery clip
• 1 × connecting cable, 45 cm long with green 5.5 × 2.5 mm coaxial plug to
5.5 × 2.1 mm coaxial plug
• 1 × connecting cable, 45 cm long with 3.5 mm audio plug to 5.5 × 2.1 mm
coaxial plug
Quick start guide
This document contains important information on the safe use of the product.
Read and follow the safety instructions and all other instructions. Keep the docu-
ment for future reference. If you pass the product on to others, please include this
document.
Contents are subject to change. Please refer to the latest version of the documenta-
tion, which is available for download at www.thomann.de.
Damage to the device due to high voltages!
The device can be damaged if it is operated with the incorrect voltage or if
high voltage peaks occur. In the worst case, excess voltages can also cause
a risk of injury and fires. Make sure that the voltage specification on the
device matches the local power grid before plugging in the device. Only
operate the device from professionally installed mains sockets that are
protected by a residual current circuit breaker (FI). Ensure that the power
cord plug is easily accessible at all times if it is the only device to safely
disconnect the device from the mains supply. As a precaution, disconnect
the device from the power grid when storms are approaching or if the de-
vice will not be used for a longer period.
Possible staining due to plasticiser in rubber feet!
The plasticiser contained in the rubber feet of this product may react with
the coating of the floor and cause permanent dark stains after some time.
If necessary, use a suitable mat or felt slide to prevent direct contact be-
tween the product's rubber feet and the floor.
Damage to the device if operated in unsuitable ambient conditions!
The device can be damaged if it is operated in unsuitable ambient condi-
tions. Only operate the device indoors within the ambient conditions
specified in the "Technical specifications". Avoid operating it in environ-
ments with direct sunlight, heavy dirt and strong vibrations. Avoid operat-
ing it in environments with strong temperature fluctuations. If tempera-
ture fluctuations cannot be avoided (for example after transport in low
outside temperatures), do not switch on the device immediately. Never
subject the device to liquids or moisture. Never move the device to anoth-
er location while it is in operation. In environments with increased dirt
levels (for example due to dust, smoke, nicotine or mist): Have the device
cleaned by qualified specialists at regular intervals to prevent damage due
to overheating and other malfunctions.
General handling
• To prevent damage, never exert force while operating the device.
• Never immerse the device in water. Wipe only with a clean and dry cloth. Do not
use liquid cleaners such as benzene, thinners or flammable cleaning agents
Keep foreign substances away from the device!
Keep the device away containers with liquid. Should liquid enter the device, this
could lead to its destruction or fire. Ensure that no metallic parts enter the device.
• Voltage and current measuring device
• High current output for modern digital effects
• LED display on each output
• LED indicator for mains operation and the charge status of the built-in battery
• 1 × voltage doubler cable, 20 cm
• 1 × current doubler cable, 60 cm
• 1 × EIAJ-05 cable
• 1 × power adapter with EU plug, 120 cm
• 1 × cable fastening set
• 1 × hook-pile tape, adhesive, 200 cm × 4.5 cm
• 1 × Allen key (5 mm)
• 1 × transport bag with stowage compartment and carrying strap
EN