Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Harley Benton PA-100
Summary of Contents for Harley Benton PA-100
- Page 1 PA-100 Power Attenuator...
- Page 2 Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 Internet: www.thomann.de 23.08.2022, ID: 406679 (V4)
-
Page 3: Table Of Contents
1.1 Further information........................... 6 1.2 Notational conventions........................6 1.3 Symbols and signal words....................... 7 Safety instructions............................. 9 Features............................... 11 Connections and controls........................12 Technical specifications........................14 Plug and connection assignment....................15 Cleaning............................... 16 Protecting the environment......................17 PA-100 Power Attenuator... - Page 4 PA-100 Power Attenuator...
-
Page 5: General Information
Our products and user manuals are subject to a process of continuous development. We there‐ fore reserve the right to make changes without notice. Please refer to the latest version of the user manual which is ready for download under www.thomann.de. PA-100 Power Attenuator... -
Page 6: Further Information
Personal consultation For personal consultation please contact our technical hotline. If you have any problems with the device the customer service will Service gladly assist you. 1.2 Notational conventions This manual uses the following notational conventions: PA-100 Power Attenuator... -
Page 7: Symbols And Signal Words
NOTICE! This combination of symbol and signal word indicates a pos‐ sible dangerous situation that can result in material and environmental damage if it is not avoided. PA-100 Power Attenuator... - Page 8 General information Warning signs Type of danger Warning – high-voltage. Warning – danger zone. PA-100 Power Attenuator...
-
Page 9: Safety Instructions
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device if covers, protectors or optical components are missing or damaged. PA-100 Power Attenuator... - Page 10 The plasticiser contained in the rubber feet of this product may possibly react with the coating of your surface and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the surface and use a suitable underlay if neces‐ sary, i.e. felt pads or similar. PA-100 Power Attenuator...
-
Page 11: Features
Input power: max. 100 W Inputs for 4 Ω, 8 Ω, 16 Ω Outputs: mic (low-impedance), line, speaker LED as overload indicator Controls: speaker level, line level Silent fan Usable as dummy load DI output with speaker simulation PA-100 Power Attenuator... -
Page 12: Connections And Controls
Connections and controls Connections and controls ö & 1 [Full Power] | LED as overload indicator 2 [Line Level] | rotary control for adjusting the signal attenuation at the line out PA-100 Power Attenuator... - Page 13 4 Ω, 8 Ω or 16 Ω! NOTICE! Damages caused by the connection to or the change of connections at an enabled amplifier Connect the device to or change connections always at the disconnected ampli‐ fier, otherwise the amplifier may be damaged. PA-100 Power Attenuator...
-
Page 14: Technical Specifications
Dimensions (W × H × D) 190 mm × 110 mm × 140 mm Weight 1.5 kg Ambient conditions Temperature range 0 °C…40 °C Relative humidity 20 %…80 % (non-condensing) Further information Noise reduction DI box Speaker simulation Dummy Load PA-100 Power Attenuator... -
Page 15: Plug And Connection Assignment
‘just’ in poor transmission quality! 1/4" TS phone plug (mono, unbalanced) Signal Ground, shielding XLR plug (unbalanced) Ground, shielding Signal Bridged to pin 1 PA-100 Power Attenuator... -
Page 16: Cleaning
The fan grids of the device must be cleaned of any contamination, such as dust, etc. on a reg‐ ular basis. Before cleaning, switch off the device and disconnect mains-operated devices from the mains. Only use pH-neutral, solvent-free and non-abrasive cleaning agents. Clean the unit with a slightly damp lint-free cloth. PA-100 Power Attenuator... -
Page 17: Protecting The Environment
Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility. PA-100 Power Attenuator... - Page 18 Notes PA-100 Power Attenuator...
- Page 20 Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de...
Need help?
Do you have a question about the PA-100 and is the answer not in the manual?
Questions and answers