1. Manuals
  2. Brands
  3. Esteam Cleaning Systems Manuals
  4. Cleaning Equipment
  5. Defender 500
  6. Owner's manual

Esteam Cleaning Systems Defender 500 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ESTEAM CLEANING SYSTEMS
DEFENDER 500 MODELS
OWNER'S MANUAL
Congratulations on your selection of a new Defender portable carpet cleaner built in
Canada by Esteam Cleaning Systems. Our goal is to produce the best, high
performance line of carpet cleaning equipment on the market today. Reading your
Owner's Manual will help to achieve maximum benefit from your purchase.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Defender 500 and is the answer not in the manual?

Questions and answers

Related Manuals for Esteam Cleaning Systems Defender 500

Summary of Contents for Esteam Cleaning Systems Defender 500

  • Page 1 OWNER’S MANUAL Congratulations on your selection of a new Defender portable carpet cleaner built in Canada by Esteam Cleaning Systems. Our goal is to produce the best, high performance line of carpet cleaning equipment on the market today. Reading your...

  • Page 2: Table Of Contents

    Technical • Warranty • Defender 500 Drawings & Parts Lists • Defender 500 With Heat Drawings & Parts Lists • Internal Heatermate • Defender 500 2 – 3 Stage Drawings & Parts List • 500PSI Pump Drawings & Parts List...

  • Page 3: Introduction

    Years of experience, engineering, and planning have gone into the design and manufacturing of the Defender 500. We take great pride in our equipment; our goal is no less than your complete satisfaction.

  • Page 4: Technical Specifications

    Technical Specifications Defender 500 Defender 500-05 Defender 500-10 Defender 200-20 Defender 200-20-05 Defender 500-20-10 ELECTRICAL One cord Two cords Two cords Amps 115 amps 15 amps per cord 15 amps per cord Volts 115 volts or 220 volts 115 volts or 220 volts...

  • Page 5: Safety

    • The two power cords must be plugged into separate circuits during operation. • Do not use the DEFENDER 500 outdoors, in standing water or on wet surfaces. Do not store the DEFENDER 500 in wet conditions. If extractor is leaking, unplug machine power cords from outlets before approaching or touching machine.
  • Page 6 Store, transport, and use this equipment only in temperatures well above freezing. (32ºF or 0ºC). If you suspect the Defender 500 has been frozen, do not plug in or turn on machine until you are sure it has thawed completely.

  • Page 7: Operation Procedures

    Operation Procedures Knowledge of the proper operation of the Defender 500 is required to ensure user safety and efficient performance of the extractor. SET UP AND OPERATION 1. Insert electrical cords into 3 pin grounded outlets. Two cord machines maybe equipped with the Optional Circuit Indicator located above the Switch Plate.
  • Page 8 TO USE YOUR DEFENDER HEATER: A. Hook the wand solution hose to the quick connect of your machine. B. Plug the heater power cord into a wall that is on a separate circuit form the other cord. C. Turn the heater switch on. D.

  • Page 9: Preventative Maintenance

    WARNING: When using electrical equipment around water it is important to wear rubber soled shoes and keep machine properly grounded at all times. Failure to do so could result in electric shock. MAINTENANCE DAILY: - Clean high water level float screen inside the recovery tank. - Ensure high level float ball is working properly.

  • Page 10: Optional Equipment

    Bucket & Sprayer Storage The top of the Defender 500 is sized and recessed to hold a five-gallon bucket or two one-gallon chemical bottles as well as two 2QT sprayers.

  • Page 11: Trouble Shooting

    TROUBLE SHOOTING WARNING: Prior to inspection or repair of this machine, disconnect all electrical cords rendering the machine powerless. Failure to do so could result in serious or fatal injury. PROBLEM CAUSE SOLUTION 1. Entire unit will not 1. Unit not plugged in 1.
  • Page 12 TROUBLE SHOOTING (CONTINUED) PROBLEM CAUSE SOLUTION 5.Pump runs but 1. Partial kink in solution hose 1. Remove kink has loss pressure 2. Partial blockage in solution 2. Remove blockage hose 3. Jet orifice opening on clean- 3. Total jet opening for 500 ing wand is too large PSI pump should be .06 or 08.
  • Page 13 TROUBLE SHOOTING (CONTINUED) PROBLEM CAUSE SOLUTION 8. Machine spits water 1. High level float not working 1. Check auto shut off float out of exhaust port properly cage and ball for proper operation 9. Machine blowing 1. Damaged (leaking) 1. Immediately shut unit excessive amounts of recovery tank fittings down.

  • Page 14: Warranty

    ESTEAM® CLEANING SYSTEMS DEFENDER EXTRACTOR WARRANTY NOTICE: REVIEW THIS WARRANTY CAREFULLY AS THIS DOCUMENT CONTAINS LIMITATIONS AND EXCLUSIONS. PART I: Esteam Manufacturing. (hereinafter referred to as "Esteam") warrants each new Defender Extractor, subject to the limitations as defined in the specific details of its warranty coverage defined below. LIMITED HOUSING WARRANTY COVERAGE: Esteam warrants the Defender Polyethylene Machine Housing Unit to be free from defects in material and workmanship (including cracking, leaking or deterioration) for three years, expressly subject to the limitations stated herein.

  • Page 15: What Is Not Covered

    PART II - REPLACEMENT PARTS (UNDER WARRANTY) Replacement warranty parts will be genuine Esteam parts, or parts of similar kind and quality. All replacement warranty parts are warranted to be free from defects in materials or workmanship from the date of the original unit purchase for the balance of the original warranty period namely: 90 days, 12 months, or the Limited Warranty, whichever is applicable;...
  • Page 16 warranties. Esteam, its officers, directors, agents, dealers and its affiliates (and their respective officers, directors, agents and dealers) shall not be liable to the customer nor to any party for any liability, including without limitation, strict liability, liability for loss, injury or damage due directly or indirectly to the use or operation of the Esteam product;...
  • Page 17 Require use of a defoamer. A vacuum motor showing moisture contamination on interior components shall void any warranty by Esteam. Pumps: All pumps require daily flushing with clean water after use. Internal Heatermate: The internal heater must be flushed with clean water after every use. Any buildup of hard water deposits or chemical buildup within the internal heater will void any Esteam warranty thusly exclude any liability of Esteam.

  • Page 18: Defender 500 Drawings & Parts Lists

    Ninja 500...
  • Page 19 Ninja 500...
  • Page 20 Ninja 500...
  • Page 21 Ninja 500...
  • Page 22 Ninja 500...
  • Page 23 Ninja 500...
  • Page 24 Ninja 500...
  • Page 25 Ninja 500...
  • Page 26 Ninja 500...
  • Page 27 Ninja 500...
  • Page 28 Ninja 500...
  • Page 29 Ninja 500...

  • Page 30: Defender 500 With Heat Drawings & Parts Lists

    Ninja 500 With Heat...
  • Page 31 Ninja 500 With Heat...
  • Page 32 Ninja 500 With Heat...
  • Page 33 Ninja 500 With Heat...
  • Page 34 Ninja 500 With Heat...
  • Page 35 Ninja 500 With Heat...
  • Page 36 Ninja 500 With Heat...
  • Page 37 Ninja 500 With Heat...
  • Page 38 Ninja 500 With Heat...
  • Page 39 Ninja 500 With Heat...
  • Page 40 Ninja 500 With Heat...
  • Page 41 Ninja 500 With Heat...

  • Page 44: Defender 500 2 - 3 Stage Drawings & Parts List

    Ninja 500 2 – 3 Stage...
  • Page 45 Ninja 500 2 – 3 Stage...
  • Page 46 Ninja 500 2 – 3 Stage...
  • Page 47 Ninja 500 2 – 3 Stage...
  • Page 48 Ninja 500 2 – 3 Stage...
  • Page 49 Ninja 500 2 – 3 Stage...
  • Page 50 Ninja 500 2 – 3 Stage...
  • Page 51 Ninja 500 2 – 3 Stage...
  • Page 52 Ninja 500 2 – 3 Stage...
  • Page 53 Ninja 500 2 – 3 Stage...
  • Page 54 Ninja 500 2 – 3 Stage...
  • Page 55 Ninja 500 2 – 3 Stage...

This manual is also suitable for:

Defender 200-20Defender 500-05Defender 200-20-05Defender 500-10Defender 500-20-10

Table of Contents