Acuity Brands nLight TouchScreen Installation Instructions

nLight TouchScreen (nTS)
INSTALLATION INSTRUCTIONS
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all
fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Installation and service should be performed by a qualified licensed electrician.
• Maintenance should be performed by qualified person(s) familiar with the products' construction & operation & any hazards involved. Regular maintenance programs recommended.
• To be installed to a circuit with overvoltage control to Overvoltage category Cat.III or less, minimum suppressionrating 6.0 kV for a 600 V ac rms system voltage
• DO NOT INSTALL DAMAGED PRODUCT! This product has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly
should be replaced.
CAUTION: RISK OF PRODUCT DAMAGE
 Electrostatic Discharge (ESD): ESD can damage product(s). Personal grounding
equipment should be worn during all installation or servicing of the unit.
 Do not touch individual electrical components, as this can cause ESD and affect
product performance.
 Do not stretch or use cable sets that are too short or are of insufficient length.
 Do not tamper with contacts.
 Do not modify the product.
 Do not change or alter internal wiring or installation circuitry.
 Do not use product for anything other than its intended use.
Contains FCC ID: 2ADCB-RMODIT3
Contains IC: 6715C-RMODIT3
IFT #: RCPNLNL20-2057
Acuity Brands Lighting Inc. RMODIT3
In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the radiator shall not be less than
20cm during normal operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
POWER SUPPLY INSTALLATION INSTRUCTIONS (FCS PS10)
1. Attach power supply to a junction box separate of the 3-gang junction box required for the nLight TouchScreen.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465
© 2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/23/22
C US LISTED
WARNING - RISK OF ELECTRIC SHOCK
 Disconnect or turn off power before installation or servicing.
 Verify that supply voltage is correct by comparing it with
the product information.
 Make all electrical and grounded connections in accordance
with the National Electrical Code (NEC) and any applicable
local code requirements.
 All wiring connections should be capped with UL
approved recognized wire connectors.
 All unused connector openings must be capped.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este
equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
www.nlightcontrols.com
Full warranty terms located at: www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Actual performance may differ as a result of end-user environment and application.
 Do not exceed maximum wattage, ratings, or published
operation conditions of product.
 Do not overload.
 Follow all manufacturer's warnings, recommendations
and restrictions to ensure proper operation of product.
 Wear gloves and safety glasses at all times when installing,
servicing or performing maintenance.
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING
• DO NOT USE OUTDOORS.
DO NOT MOUNT NEAR GAS OR ELECTRIC HEATERS.
•
• EQUIPMENT SHOULD BE MOUNTED IN LOCATIONS AND AT
HEIGHTS WHERE IT WILL NOT READILY BE SUBJECTED TO
TAMPERING BY UNAUTHORIZED PERSONNEL.
• THE USE OF ACCESSORY EQUIPMENT NOT
RECOMMENDED BY THE MANUFACTURER MAY
CAUSE AN UNSAFE CONDITION.
WARRANTY
5-year limited warranty.
NOTE: Specifications subject to change without notice.
WARNING - RISK OF BURN or FIRE
CAUTION - RISK OF INJURY
IMPORTANT SAFEGUARDS
THE FOLLOWING:
1 of 2