1. Manuals
  2. Brands
  3. XtremepowerUS Manuals
  4. Sander
  5. 46001
  6. Owner's manual and safety instructions

XtremepowerUS 46001 Owner's Manual And Safety Instructions

Disc sander 4” x 36”
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 46001 and is the answer not in the manual?

Questions and answers

Related Manuals for XtremepowerUS 46001

Summary of Contents for XtremepowerUS 46001

  • Page 2: Table Of Contents

    Table of Contents Safety ....2 Maintenance ........12 Specifications ....6 Parts List and Diagram ..14 .... 16 Setup ............6 Warranty Operation ........... 9 WARNING SyMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

  • Page 3: Extension Cord

    13. DON'T OVERREACH. Table A: REcOMMENDED MINIMUM WIRE GAUGE Keep proper footing and balance at all times. FOR EXTENSION c ORDS (120 VOLT) MAINTAIN TOOLS WITH CARE. Keep tools sharp EXTENSION c ORD and clean for best and safest performance. Follow NAMEpLATE instructions for lubricating and changing accessories.

  • Page 4: Sander Safety Warnings

    Grounding Instructions LJ:::::. TO PREVENT ELECTRIC SHOCK AND DEATH FROM INC ORREC T GROUNDING WIRE cCONNECTION READ AND FOLLOW THESE INSTRUCTIONS: 110-120 VAc Grounded Tools: Tools with Three prong plugs In the event of a malfunction or breakdown, Repair or replace damaged or grounding provides a path of least resistance for worn cord immediately.

  • Page 5: Safety

    9. DO NOT OPERATE WITH ANy GUARD 14. Industrial applications must follow OSHA guidelines. DISABLED, DAMAGED, OR REMOVED. Moving 15. Maintain labels and nameplates on the tool. guards must move freely and close instantly. These carry important safety information. The use of accessories or attachments not recommended by the manufacturer may 16.

  • Page 6: Specifications

    Specifications Electrical Rating 120VAC / 60Hz / 3.5A Belt Size 4"W x36"L Disc Size 6" 1819 RPM (Disc) Maximum Speed 1185 FPM (Belt) Setup - Before Use: ./'t.. Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
  • Page 7 Mounting Backing Disc 1. Slide the Backing Disc (5) onto the Drive Axle (54 ). The Set Screw (6) must face the flat surface of the Drive Axle. Refer to Figure C. Note: For clarity, installed Disc Cover is not shown. 2.
  • Page 8 Mounting Fence Machine Screws 1. The Fence (63) fits across the top of the sanding belt to prevent workpiece from moving to the rear when sanding. 2. Align two Tabs on the Fence with two holes on the top of the Belt End Guard (58). Place Fence tabs underneath the Belt End Guard.

  • Page 9: Tool Set Up

    /),. Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this ... manual including all text under subheadings therein before set up or use of this product. Tool Set Up A.WARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section.
  • Page 10 Set Belt/Disc Sander in vertical position by Mounting Table for Use as Belt Sander loosening both Nuts (22). Raise the Belt Support No t e: The Table (69) may be used for both Housing (52). When it is vertical, wrench tighten horizontal and vertical operations.

  • Page 11: Workpiece And Work Area Set Up

    Mounting Sanding Discs Note: Before using the Sanding Disc the first Peel off old Sanding Disc. time, wipe down the Backing Disc with denatured 3. Align perimeter of new Sanding Disc alcohol (shellac thinner). This will clean the surface, over the Backing Disc (5) and press leave no residue and assure a secure bond.

  • Page 12: Maintenance

    Maintenance and Servicing procedures not specifically explained in this manual must .. be performed only by a qualified technician. AWARNING TO pREVENT SERIOUS INJURy FROM Ace IDENTAL OpERATION: Turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section.

  • Page 13: V-Belt Replacement

    V-Belt Replacement Remove Set Screws (6) and pull off Backing Place the new V-Belt (12) onto the Spindle Disc (5). Pulley, by using a flat screwdriver (not supplied) as a wedge. Turn the Spindle Pulley and Remove four Screws (11) and Washers (10) ride the new V-Belt onto the Motor Pulley.
  • Page 14 oart Descriotion Q t v oart Descriotion Q tv Screw M4x12 Power Cord Flat Washer Motor Front Cover Washer 5 Sandino Disc Retaininq Rina 12 Backino Disc Ball Bearina Front Roller Screw M8x8 Screw M4x8 Adiustina Bracket Disc Cover Sprinq Outer Pullev Cover Shaft Washer...

  • Page 16: Please Read The Following Carefully

    XtremePowerUS makes no representations or warranties with respect to this manual or with respect to the products described herein. XtremePowerUS shall not be liable for any damages, losses, costs or expenses, direct, indirect or incidental, consequential or special, arising out of, or related to the use of this material or the products described herein.

Table of Contents