QRS PMII Troubleshooting

QRS
QRS
Remotes that Remotes that won't control
QRS QRS
Baldwin ConcertMaster CD Baldwin ConcertMaster CD
Serenade CD Serenade CD
QRS QRS
Baldwin ConcertMaster ATP2 Baldwin ConcertMaster ATP2
Serenade Pro Serenade Pro
QRS QRS
Any other legacy Any other legacy
QRS QRS
Remotes with limited control Remotes with
QRS QRS
Pianomation MIDI remotes Pianomation MIDI remotes
QRS QRS
Used with 2000c, 2000CD, Chili, Petine and Ancho. Used with 2000c, 2000CD, Chili, Petine and Ancho.
The The PNOmation II and the small red 10-button. PNOmation II and the small red 10-button.
QRS QRS
Used with PMII and PNO3. Used with PMII and PNO3.
Plx #3 is the Plx #3 is the Network Mode Indicator light Network Mode Indicator light for the PMII & PNO3 processors.
T T
here are two versions of the Plx box, but the network mode indicator light is the same for both: here are two versions of the Plx box, but the network mode indicator light is the same for both:
Green = Stand Alone Green = Stand Alone
Yellow Solid = Network Mode-DHCP Yellow Solid = Network Mode-DHCP
Yellow Flashing = Network - Static IP Yellow Flashing = Network - Static IP
Red Solid = No Wi-Fi Detected Red Solid = No Wi-Fi Detected
Red Flashing = Acquiring IP Address Red Flashing = Acquiring IP Address
Changing Network Modes on PMII & PNO3 Processors Without a Remote Changing Network Modes on PMII & PNO3 Processors Without a Remote
If you don't have a remote or the remote is not changing the mode, you can use button #3 at the end of the processor. If you don't have a remote or the remote is not changing the mode, you can use button #3 at the end of the processor.
PNO3WB: DO NOT USE Button #3, "holding for three seconds" to change modes. PNO3WB: DO NOT USE Button #3, "holding for three seconds" to change modes.
This will set the Network LAN mode to Static IP and PLx #3 will continue to flash. This will set the Network LAN mode to Static IP and PLx #3 will continue to flash.
The PNO3WB has built-in WiFi and a remote is not needed. The PNO3WB has built-in WiFi and a remote is not needed.
If the PNO3WB'S If the PNO3WB'S
Press & Hold buttons 1 & 2 for 2 Seconds, you should hear a ding over the speaker. This will Enable the Press & Hold buttons 1 & 2 for 2 Seconds, you should hear a ding over the speaker. This will Enable the QRS
Note the color of PLx #3 light. Note the color of PLx #3 light.
Press and Press and Hold Hold button button #3
Watch and wait for the #3 PLx light to change color. Watch and wait for the #3 PLx light to change color.
Repeat holding #3 for 4 seconds until the correct mode displays. Repeat holding #3 for 4 seconds until the correct mode displays.
QRS Music Technologies, Inc.
Troubleshooting Troubleshooting
Remotes / PMII & PNO3 Network Modes
won't control a PMII or PNO3 a PMII or PNO3
remote that is not shown below. remote that is not shown below.
limited control of PMII or PNO3 of PMII or PNO3
WI-FI is not broadcasting, use buttons 1 & 2 on the processor. WI-FI is not broadcasting, use buttons 1 & 2 on the processor.
QRS QRS
PMII or PNO3-without built-in Wi-Fi PMII or PNO3-without built-in Wi-Fi
#3 for for 4 Seconds 4 Seconds and release. Holding longer will reboot the system. and release. Holding longer will reboot the system.
for the PMII & PNO3 processors.
1
qrsmusic.com
Read below to recover. Read below to recover.
QRS "Standalone" Wi-Fi. "Standalone" Wi-Fi.
800.247.6557