Page 2
Ta=25ºC BVP525 50000h 164000 1160 35° C -40° C 35,5 BVP525 50000h 143000 45° C -40° C 35,5 BVP515 100000h 134000 15° C -40° C 29,5 BVP515 100000h 129000 20° C -40° C 29,5 BVP515 100000h 124000 25° C -40° C 29,5 BVP515 100000h...
Page 3
BVP525 HGB BVP525 BV BVP515 HGB BVP515 BV HGB VERSION BV VERSION BRACKET FIXATION DETAIL In luminaire version for swimming pool applications (SWP): Fixture mounting system (including fasteners) needs to be compliant with EN 13451-1 or MIS 1203 Mounting system and product shall be a subject of periodical inspection at least every year. Any rusted element needs to be replaced.
Page 4
POSITIONS NOT ALLOWED In case of using only one fixation point and if the luminaire is higher >3m, the use of a 2nd fixing security system is needed RECOMMENDED WASHER The fasteners have to resist environment corrosion. ACCORDING TO DIN9021 Stainless steel screws not recommended and protective coating might be applied.
MAINTENANCE Mark the position with a pen (to remember the posi- tion) before untighting the grub screw and rotate the luminaire. Disconnect from connection Connect the cable of the module to the connection Rotate back to the marked position before tightening 5/16...
LIGHT MODULE LABEL OPTIC TYPE 12 NC: 9123XXXXXXXX I : 0,8-2,0 A Tc: 90ºC OPTIC TYPE NB/MB/WB/VBW CLEANING 1. Remove physical elements that can block and modify the aircooling (heatsink fins) 2. Cleaning Frequency (depending on installa- tion place and environment) Pollution Category Cleaning Interval (months)
Page 7
ACCESORIES LOUVRE (8x) 4x10mm screws 12NC: 912300022867 (ZVP520 L-A90): External zero candela louvre 12NC: 912300022588 (ZVP420 L): External spill-light control louvre (8x) 4x10mm screws 12NC: 912300022990: ZVP500 L-A90 (2 PCs) Ext. zero candela louvre 12NC: 912300022989: ZVP500 L (2 PCs) External spill-light control louvre PRECISION AIMING DEVICE ZVP520 PAD A30 (for A-Optics) 12NC: 910503910040...
Page 8
EVP500 OptiVision LED gen2 Driver box EVP500 380-400V 50Hz Driver box Features Iin (Mains 220V-240V) Iin (Mains 380V-400V) 4.6A Inrush (220V-240V) 20 A during 160 µs Inrush (380V-400V) 30 A during 160 µs Power Factor > 0.95 at full power * According to the maximum Surge Protection 10kV Com.
Page 9
ELECTRICAL CONNECTION L<50m DALI MAINS Cable from Driver box to Connection Box CONNECTION CONNECTION MAINS MAINS DALI Ø min Ø max TORQUE MAX VOLTAGE RECOMMENDED CABLE TYPE CONNECTOR (mm) (mm) SUPPORTED S E C T I O N H05VV-F (3182-Y) 2 DALI Cable Ø...
Page 10
H07RN-F 450V/750 or A11VV U-600/1000V 50m<L<200m 8G2.5 Ø13-Ø18 1000 V H07RN-F 450V/750 or A11VV U-600/1000V CABLE NOT SUPPLIED BY PHILIPS IN VERSION BV Ø min Ø max TORQUE Cables to Modules Ø 10 Ø 14 3 Nm Cable to Driver box Ø...
Page 11
ELECTRICAL CONNECTION 50m<L<200m 50m<L<200m CABLE NOT SUPPLIED BY PHILIPS IN VERSION BV 8G2,5 mm2 cable DRIVER LUMINAIRE 3-POLE TERMINAL BLOCK NOT SUPPLIED BY PHILIPS 11/16...
Page 12
Installation of drivers boxes on cabinet ORIENTATION DISTANCES Each driver box in the cabinet has to be in vertical position The distances between driver box- es or wall have to be higher than: Item Distance 1, 3 Min 50mm Min 80mm Min 150mm Min 200mm Cables...
Page 13
Installation of driver boxes in the mast minimum width of the door: 125mm minimum height of the door: 600mm Depending of the driver fixation in the mast, please select the most suitable hook. 13/16...
Page 14
Installation of driver boxes on the bracket or in horizontal position BOTTOM Breathers cannot be exposed directly to water 14/16...
Page 15
Maximum number of luminaires to be connected to standard circuit breakers (fuse) BVP515 Mains voltage Max Nr luminaires connected MCB 16A A type 220V-240V MCB 16A B type 220V-240V MCB 32A A type 220V-240V MCB 32A B type 220V-240V MCB 16A A type 380V-400V MCB 16A B type 380V-400V...
Need help?
Do you have a question about the OptiVision BVP525 and is the answer not in the manual?
Questions and answers