Page 2
Co p y r i g h t : LANG T e chnik GmbH Impressum Albstraße 1–6 D-73271 Ho l zmaden Germany This documentation c ontains ins t ructions and inf ormation that may no t be reproduced, distributed, or transmitted by data processing methods in who le or in par t or used for competitive purposes without authorization.
Contents Chapter 1 Product Description On Page 1. 1 Gener al 1. 2 Built 1. 3 Scope of delivery 1. 4 Holding s erration o f the clamping jaws 1. 5 Version 1. 6 Accessories 1. 7 Service option 1. 8 Compatibility 1.
Product description 1.1 General The Makr o•Gr ip and Makr o •Gr ip FS 5-Axis Vises ar e machining vises t h at are used in milling op e rations on CN C ® ® machine tools. They hold the workpiece (raw or finished par t ) with their c lamping jaws in the center of the vise during the machining pr o cess.
Product description 1.2 Built Base body made of case-hardened steel ① Threaded spindle inc l uding c e nter piece ② Clamping jaws with holding serr a tion ③ NOTE The serial numb er of the two clamping jaws must always be identical! Quick•Point clamping studs / int e grated zero point int e rface ④...
Product description 1.4 Holding serration of the clamping jaws 1.4.1 Makro•Grip ® The holding t e eth and dep th stop alternate in the holding serration o f a Makr o•Gr ip 5-Axis Vise (see illus t ration) . ® The distance from ho lding t o oth to holding t o oth is 6 mm.
Page 7
Product description Makro•Grip FS 5-Axis Vise ® QTY clamping Item no. Description Jaw width Base length Spindle Spindle length Clamping range studs Makr o•Gr ip® F S 46 48040-46 FS 46 mm 77 mm Ø 12 mm x 1, 0 82 mm 0 - 65 mm micr o...
Product description 1.6 Accessories Wrenches for Makro•Grip 5-Axis Vises ® Item no. 5-Axis Vise size Size 45510 External he xagon SW 8 45500 External he xagon SW 12 45501 External he xagon SW 15 45515 Allen k ey SW 4 45505 Allen k ey 77/ 12 5...
Page 9
Product description 1.7.3 Customer-specific clamping depth (order no. 47000-02) The standard clamping dep th / supp ort height of workpieces in the clamping jaws of Makr o•Gr ip (FS) 5-Axis ® Vises is 3 mm. On request, this supp ort height can b e adjusted. Illustration: Left: Standard support height or c lamping dep th (3 mm) .
Product description 1.8 Compatibility Al l vise types from LAN G T echnik ( M akr o•Gr ip / Makr o •Gr ip FS / Profilo / A vanti / V ario•Tec) use the same base ® ® body in dif f erent lengths and widths. This ensur es that all jaw types are fully c ompatible with each other. Suitable jaw types can be added as required.
Technical data 2.1 General data and tightening torques Base body External Max. Tightening torque Allen key size Centering accuracy [mm] width hexagon size [Nm] ±0,02 ±0,02 ±0,02 2.2 Clamping pressure and clamping force The following table shows the torque values in r e lation to the clamping force. Holding f o rce [N] Torque [Nm] 2.3 Zero point interface...
Installation 3.1 Attach the Makro•Grip (FS) 5-Axis Vise to the machine table ® Prerequisite for mounting on a machine table: The appropriate zero point clamping system is r equired to mount t h e 5-Axis Vise on a mac hine table. With its four (or two) mount e d Qu ick•Point clamping studs, the 5-Axis Vise is p laced in the corresponding lo cating ho les of ®...
Operation 4.2 Dismantling and turning / inserting the clamping jaws NOTE The instructions for disassemb ling and r e assembling the jaws apply to all types of vises from LANG T e chnik . Turning t h e jaws refers exclusively to Makr o•Gr ip (FS).
Damaged parts must be replaced immediat e ly with faultless parts. In the event of damage or f a ults, please directly contact LANG Technik GmbH • Albstraße 1–6 • D-73271 Holzmaden • Phone: +49 7023 9585-0 5.2 Lubricant The Makr o•Gr ip (FS) 5-Axis Vise is supp l ied without lubrication p oints.
Maintenance 5.6 Spare parts Spare parts may be required for the maint e nance and repair o f the Makr o•Gr ip (FS) 5-Axis Vise. Inf ormation that ® you should hav e ready for or dering spar e parts from the manu facturer LANG T e chnik GmbH is as f ollows: Minimum specification when ordering: Designation o f the Makr o•Gr ip (FS) 5-Axis Vise...
Warning 7.1 Intended use The operator under t akes to use the product properly with caution and under appr opriate conditions. No liab ility or reimbur sement is ac cepted for impr o per use. Onl y use the Makr o•Gr ip (FS) 5-Axis Vise if y o u have read and under s tood the operating ins tructions in f u ll ®...
Explanation of Symbols 9.1 Symbols Please pay attention to the following warning symbols Read all the operating ins tructions car e fully before commissioning f or the first time and k eep it in a saf e place for future use Please read and follow the technical and saf e ty instructions The use of protective gloves made of tough, resistant material is r ecommended A helme t and safety goggles are recommended f o r personal safety...
Need help?
Do you have a question about the Makro Grip and is the answer not in the manual?
Questions and answers