Altinex UT240 Series User Manual

UT240-200S
Under the Table Interconnect Solutions
Welcome!
We greatly appreciate your purchase of the UT240 Series. We
are sure you will find it reliable and simple to use. Superior
performance for the right price, backed by solid technical and
customer support is what Altinex offers.
We are committed to providing Signal Management Solutions®
to our customers for the most demanding audiovisual
installations at competitive pricing and we welcome you to join
the ranks of our many satisfied customers throughout the world.
1. Precautions and Safety Warnings
Please read this manual carefully before using your UT240
series Interconnect. Keep this manual handy for future reference.
These safety instructions are to ensure the long life of your
UT240 and to prevent fire and shock hazards. Please read them
carefully and heed all warnings.
1.1 General
•
Unauthorized personnel shall not open the unit as there
are high-voltage components inside. Qualified Altinex
service personnel or their authorized representatives
must perform all service.
1.2 Installation Precautions
•
For best results, place the UT series Interconnect unit in
a dry area away from dust.
•
To prevent fire or shock, do not expose this unit to water
or moisture. Do not place the unit in direct sunlight, near
heaters or heat-radiating appliances, or near any liquid.
Exposure to direct sunlight, smoke, or steam can harm
internal components.
•
Handle carefully; dropping or jarring can cause damage.
•
Disconnect the power cord to turn off the power. The
power outlet should be installed near the equipment and
be easily accessible.
2. Installation Procedures
Note: Download and read the entire online manual to become familiar with the UT260-200S and for detailed information.
Note: The UT240-200S installs horizontally, under a table or on the back of a desk or inside a podium.
However, it may also be installed vertically.
Step 1 Locate the best position for your UT240-200S, but do NOT mount it to
the surface until cables are ready.
Step 2. Install up to three RT300 series retractable cables if needed in to the
UT240-200S. Use bushings provided with the UT unit. If one or more
retract units are not installed, install plugs provided.
Step 3. Secure the unit under the table using the metal screws provided with
the unit.
Step 4. Use the cable clamps provided to secure the cables to the bottom of
the table/desk.
Limited
3. Warranty/Return Policies
Please see the Altinex website at
400-0755-001
www.altinex.com for details on warranty and return policies.
•
We recommend using wall outlets with a Ground Fault
Circuit Interrupter (GFCI) for maximum protection.
•
Install cables according to the instructions found herein.
Do not force or pull any cables attached to the unit
1.3 Cleaning
•
Surfaces should be cleaned with a dry cloth. Never use
strong detergents or solvents such as alcohol or thinner.
Do not use a wet cloth or water to clean the unit.
1.4 FCC Notice
•
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
•
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and if not
installed and used in accordance with instructions found
herein, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
•
Any changes or modifications to the unit not expressly
approved by Altinex, Inc. could void the user's authority
to operate the equipment.
1
User's Guide