National Instruments PXIe-4080 Manual
Pxie, 6 1/2-digit, +-300 v, onboard 1.8 ms/s isolated digitizer, pxi digital multimeter
Hide thumbs
Also See for PXIe-4080:
- Getting started manual (18 pages) ,
- Calibration procedure (28 pages)
Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for National Instruments PXIe-4080
Summary of Contents for National Instruments PXIe-4080
- Page 1 PXIe-4080...
-
Page 2: Table Of Contents
SPECIFICATIONS PXIe-4080 PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter These specifications apply to the PXIe-4080. Contents Definitions..........................2 Conditions..........................2 DC Voltage Specifications......................2 Accuracy........................... 2 Noise..........................4 General..........................4 Resistance Specifications......................5 Accuracy........................... 5 Noise..........................6 General.......................... -
Page 3: Definitions
Shock and Vibration........................15 Compliance and Certifications....................16 Safety Compliance Standards..................16 Electromagnetic Compatibility..................16 CE Compliance ......................17 Product Certifications and Declarations................. 17 Environmental Management................... 17 Definitions Warranted specifications describe the performance of a model under stated operating conditions and are covered by the model warranty. The following characteristic specifications describe values that are relevant to the use of the model under stated operating conditions but are not covered by the model warranty. - Page 4 4 + 1 0.3 + 0.3 300 V 6 + 6 30 + 20 35 + 20 4 + 1 0.3 + 0.3 In parallel with 150 pF, typical Relative to external calibration source. 4080 Specifications | © National Instruments | 3...
-
Page 5: Noise
Noise Figure 1. DC Voltage Noise, Typical 300 V 100 V 100 m 10 V 100 mV 10 m 100 µ 10 µ 1 µ 100 n 10 n 1 μ 10 μ 100 μ 100 n 10 m 100 m Aperture Time (Seconds) With input shorted, Normal DC Noise Rejection, and Auto Zero ON. -
Page 6: Resistance Specifications
Perform offset nulling or add 2 ppm of range to the specifications. 2-wire resistance measurement only. Use tempco outside T +/- 10 °C. Typical accuracy is 5% extcal between 105 MΩ and 1.05 GΩ. 4080 Specifications | © National Instruments | 5... -
Page 7: Noise
Noise Figure 2. PXIe-4080 Resistance Noise, Typical 100 k ≥10 MΩ Range 1 MΩ Range 10 k 100 kΩ Range 10 kΩ Range 1 kΩ Range 100 Ω Range 100 m 10 m 100 µ 1 μ 10 μ 100 μ... -
Page 8: Noise
20 + 15 550 + 20 8 + 1 <800 mV 20 + 15 700 + 50 8 + 2 Noise Figure 3. PXIe-4080 DC Current Noise, Typical 100 μ 200 mA 20 mA 10 μ 1 μ 100 n 10 n 1 μ... -
Page 9: General
Table 4. AC Voltage Accuracy ± (% of reading + % of range), 2 Years, T ± 10 °C, extcal ± 5 °C selfcal Range Peak 1 Hz to >40 Hz to >20 kHz to >50 kHz >100 kHz (rms) Voltage 40 Hz 20 kHz... -
Page 10: General
15 Hz to 500 kHz Period measurement range 2 µs to 66.67 ms Specification is typical above 5 kHz. -10% to 0% tolerance, typical. Up to 4.5 V measurement for 1 mA test current. 4080 Specifications | © National Instruments | 9... -
Page 11: Temperature Specifications
AC Input Corresponding Minimum Maximum Accuracy Voltage Isolated Digitizer Peak-to-Peak Peak-to-Peak Range Range Signal Signal Amplitude Amplitude 50 mV 100 mV 5 mV 200 mV Refer to the PXIe_CLK100 accuracy 500 mV 50 mV of the chassis. 10 V 500 mV 20 V 50 V 100 V... -
Page 12: Isolated Digitizer Specifications
30 kHz 240 kHz Input impedance in parallel with 150 pF, typical. When AC coupled, only 1 MΩ available. Typical AC coupled frequency is 6 Hz (±0.1 dB) and 0.8 Hz (-3 dB). 4080 Specifications | © National Instruments | 11... - Page 13 Figure 4. PXIe-4080 Voltage Waveform Noise, Typical 300 V Range 100 V Range 10 V Range 100 m 1 V Range 100 mV Range 10 m 100 µ 10 µ 1 µ 100 n 10 k 100 k 10 M Sample Rate (Samples per Second) With input shorted.
-
Page 14: General Specifications
Figure 5. PXIe-4080 Current Waveform Noise, Typical 1 A Range 200 mA Range 20 mA Range 100 μ 10 μ 1 μ 100 n 10 n 10 k 100 k 10 M Sample Rate (Samples per Second) With input open. -
Page 15: Timing
HI SENSE 300 VDC or AC LO SENSE 300 VDC or AC When this fuse symbol is marked on a device, take proper precautions. Fuse This icon denotes a warning advising you to take precautions Hazardous Voltage to avoid electrical shock. Timing Mode Trigger Latency... -
Page 16: Environment
5 Hz to 500 Hz, 0.3 g (Tested in accordance with IEC 60068-2-64.) Nonoperating 5 Hz to 500 Hz, 2.4 g (Tested in accordance with IEC 60068-2-64. Test profile exceeds the requirements of MIL-PRF-28800F, Class 3.) 4080 Specifications | © National Instruments | 15... -
Page 17: Compliance And Certifications
Compliance and Certifications Electromagnetic interference can adversely affect the measurement Caution accuracy of this product. The input terminals of this device are not protected for electromagnetic interference. As a result, this device may experience reduced measurement accuracy or other temporary performance degradation when connected cables are routed in an environment with radiated or conducted radio frequency electromagnetic interference. -
Page 18: Ce Compliance
NI products in your region, visit ni.com/environment/weee. 电子信息产品污染控制管理办法（中国 RoHS） National Instruments 符合中国电子信息产品中限制使用某些有害物 中国客户 质指令(RoHS)。关于 National Instruments 中国 RoHS 合规性信息，请登录 。(For information about China RoHS ni.com/environment/rohs_china compliance, go to ni.com/environment/rohs_china 4080 Specifications | © National Instruments | 17... - Page 19 For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your patents.txt ni.com/patents software, the file on your media, or the National Instruments Patent Notice at . You can find information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer ni.com/legal/export-compliance...
Need help?
Do you have a question about the PXIe-4080 and is the answer not in the manual?
Questions and answers