1. Before You Start Package Contents TEW-638PAP Multi-Language Quick Installation Guide CD-ROM (Utility and User's Guide) AC Power Adapter (12V DC, 0.5A) Cat. 5 Ethernet Cable (0.6m / 2ft.) System Requirements Web Browser: Internet Explorer (6 or higher) A computer with a network adapter or wireless adapter properly installed A router with an available network LAN port An available DHCP Server –...
2. Hardware Installation Note: 1. Locate an optimum location for the Access Point. The best place for the Access Point is usually at the center of your wireless network. 2. Disable any anti-virus and firewall programs before starting hardware installation. 3.
Page 5
5. Connect the provided RJ-45 cable from a LAN port on your Router to the LAN port on the TEW-638PAP. Then click Next. 6. Connect a RJ-45 cable from a LAN port on your Router to the Ethernet port on your computer. 7.
Page 6
9. Enter a password and then click Login. The default password is admin. 10. Select Access Point and then click Next. Note: For AP Client setup, please refer to the User's Guide for step by step instructions. The User's Guide can be found on this product's CD-ROM.
Page 7
13. Enter a SSID and then click Next. By default, the SSID is TRENDnet638PAP. 14. Select the desired Wireless Mode and then click Next. 15. Select a Security Mode and then click Next (example shows WPA-PSK). 16. Select the desired WPA mode, enter characters for your Pre-Shared key and then click Next.
Page 8
17. Click Save (optional). 18. Give the file a name, then click Save (optional). 19. Click Configure to apply the settings. 20. Click Exit.
Troubleshooting section, User's Guide on the Utility CD-ROM, or TRENDnet's website at http://www.trendnet.com. Register Your Product To ensure the highest level of customer service and support, please take a moment to www.trendnet.com/register register your product Online at: Thank you for choosing TRENDnet...
3. Power-over-Ethernet Installation Using the TEW-638PAP with a PoE switch 1. Connect a RJ-45 cable from the Power-Over- Ethernet Switch (e.g. TRENDnet TPE-80WS) to the LAN port on the Access Point. 2. Verify that the wireless, LAN, and power LEDs...
Page 11
Using the TEW-638PAP with the TPE-111GI 1. Connect the Power Cord to the Injector. 2. Connect the Injector to the DC 48V IN connector on the TPE-111GI. Then connect the Power Cord to an outlet. 3. Connect a CAT-5 cable from a switch to the TPE-111GI's DATA IN port.
Troubleshooting 1. All the settings are correct, but I can not make a wireless connection to the Access Point. Double check that the wireless LED on the Access Point is lit. 2. Power cycle the Access Point. Unplug the power to the Access Point. Wait 15 seconds, then plug the power back in.
Page 13
3. Plug the device into a different port on the PoE switch. 4. Try using another Cat-5e cable. If you still encounter problems or have any questions regarding the TEW-638PAP, please contact TRENDnet's Technical Support Department.
Page 15
The source codes are available for download from TRENDnet's web site (http://trendnet.com/downloads/list_gpl.asp) for at least three years from the product shipping date. You could also request the source codes by contacting TRENDnet. 20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511.
Page 16
GPL/LGPL informações Gerais Este produto TRENDnet inclui software gratuito desenvolvido por terceiros. Estes códigos estão sujeitos ao GPL (GNU General Public License) ou ao LGPL (GNU Lesser General Public License). Estes códigos são distribuídos SEM GARANTIA e estão sujeitos aos direitos autorais dos desenvolvedores. TRENDnet não presta suporte técnico a estes códigos.