Miller Pet Lodge RHCK1 Assembly Instructions

Features:
• Easy to clean, rust resistant
galvanized steel construction
• Bottom panel with 1/2 x 1"
spacing
• Side and top panels with
1 x 2" spacing
Each Rabbit Hutch Contains:
1 Bottom Panel Guards
1 Back Panel 1 Spring
1 Front Panel 1 Door Latch
1 Door Panel 4 Frame Legs
2 Side Panels 2 Tray Brackets
1 Top Panel 1 Dropping Pan
4 Vinyl Door 1 Water Bottle
Tools Required:
• Wire Clip Pliers (see
instructions at right)
• Wire Cutter
Using the ACP2 Wire Clip Pliers:
1. Place ACC1 Wire Cage Clip in the pliers. See Figure 1.
2. Position clip next to wires to be fastened.
3. Close the pliers to form clips around wires
CAUTION: Avoid pinching skin in pliers.
Assembly Instructions:
NOTE: If you want to put the door on the left side of the front
panel, reverse the position of the door and feeder hole shown.
1. Cut out a hole in the front panel for the feeder using a wire
cutter. See Figure 2.
2. Lay out the hutch panels as shown in Figure 3. You can put the
door on the right or left side of the front of the hutch.
3. Fasten a clip at each . Do not put clips where
4. Raise two adjoining panels so that they meet at the corner.
Fasten clips at each shown in Figure 4. Repeat for the other
corners.
5. Attach the door on the inside of the hutch using clips at each
shown in Figure 5.
6. Slide the vinyl door guard over the edge of the door opening.
7. Place the top panel on top of the side panels. Fasten clips at each
shown in Figures 6. Do not put clips where the
8. Install a frame leg at each
NOTE: Wire clips cannot be used where the legs are to be
installed. If necessary, remove any clips in these locations.
9. Ensure that the top wire of the side panel fi ts over the prongs on
the legs as shown in Figure 7. If necessary, bend the prongs out
slightly with a screwdriver. Install the bolts, washers, and nuts
(fi nger tight only at this time).
10. Install the pan rails on the wide prongs as shown in Figure 7.
11a. When assembling one frame kit (not stacking hutches)
complete the assembly by tightening the bolts, washers, and
nuts for each leg.
11b. When assembling two frame kits (stacking hutches) proceed to
step 12.
12 Install another set of legs beneath the fi rst set as shown in Figure
8. Make sure the small tabs on the upper leg fi t over the top of
the lower leg. Install the bolts, washers, and nuts (fi nger tight
only at this time).
RHCK1 Rabbit Hutch Complete Kit
• Spring tension door latch
• Vinyl door guard
• Stackable frame kit
• Dropping pan
• Water bottle
• Feeder
1 Feeder
1 Package Wire
Clips
1 Wire Clip Pliers
4 Bolts, washers,
and nuts
• Straight Blade Screwdriver
• Two 7/16" Wrenches
appears.
appears.
shown in Figure 7.
Miller Manufacturing Company
1450 West 13th Street • Glencoe, MN 55336 • Customer Service 800-260-0888 • FAX 651-982-5101
For more information visit www.miller-mfg.com
Assembly Instructions
Assembly Instructions
13. Position the second hutch on the lower set of legs (another
person is helpful when lowering the second hutch into
position).
14. Install the pan rails on the wide prongs as shown in Figure 7.
15. Tighten all fasteners securely.
16. Install the feeder, water bottle, and dropping pan as shown in
Figure 9.
Wire Clip
Figure 1
Front Panel
Cut hole for feeder using wire cutter
Figure 2
Figure 3
MANUAL
:
(continued)
Clip
No Clip