Subscribe to Our Youtube Channel
Related Manuals for SMC Networks MXQ32 X2600 Series
Summary of Contents for SMC Networks MXQ32 X2600 Series
- Page 1 文書 No.DOC1096009 PRODUCT NAME Air Slide Table MODEL/Series /Product Number MXQ32-***-X2600...
-
Page 2: Table Of Contents
Contents Safety Instructions ......................3,4 1. Product Specifications 1-1. Specifications ..................... 5 1-2. Option ......................... 5 2. How to use 2-1. Mounting......................6,7 2-2 .Air supply......................8 2-3 .Piping ......................... 8 2-4. Operating Environment ..................9 2-5. Lubricating ......................9 2-6. -
Page 3: Safety Instructions
Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) , and other safety regulations. -
Page 4: Limited Warranty And Disclaimer/Compliance Requirements
Safety Instructions Caution We develop, design, and manufacture our products to be used for automatic control equipment, and provide them for peaceful use in manufacturing industries. Use in non-manufacturing industries is not covered. Products we manufacture and sell cannot be used for the purpose of transactions or certification specified in the Measurement Act. -
Page 5: Product Specifications
1. Product Specifications 1-1 Specifications Model MXQ32-***-X2600 Φ32 Bore size (mm) Port size Rc1/8 Fluid Action Double acting Operating pressure 0.15～0.7MPa Proof pressure 1.05MPa Ambient and fluid temperature -10 to 60℃(No freezing) Operating speed range 50 to 500mm/s Note) (Average operating speed) Rubber cushion(Standard, adjuster option/rubber stopper) Shock absorber(Adjuster option/shock absorber) Cushion... -
Page 6: How To Use
2. How to use Warning For general actuator use guidelines, be sure to refer to the Actuator/Precautions of the catalog (Best Pneumatics No.③) before using it. 2-1. Mounting (1) Mounting of body Three types of installation are available according to the machine or work piece. 1. - Page 7 (3) Precautions for mounting Caution ➀ Do not dent or scratch the mounting surface of the body, table or end plate. Damage can cause reduction in flatness, play in the guide and an increase in sliding resistance. ➁ Do not dent or scratch the rolling surface of the guide rail or guide block.
-
Page 8: Air Supply
2-2. Air supply Warning ① Use clean air Do not use compressed air which contains chemicals, synthetic oils containing organic Solvents, salts or corrosive gases, etc., as this can cause damage or malfunction. ➁ High levels of condensate Compressed air containing a large amount of condensate can cause the pneumatic equipment to malfunction. -
Page 9: Operating Environment
2-4. Operating Environment Warning ➀ Do not use in environments where there is a danger of corrosion. Refer to the construction drawings regarding cylinder materials. ➁ Do not subject the product to direct sunlight. ➂ Do not operate in a location subject to vibration or impact. Contact SMC when product is used in such environmental conditions. -
Page 10: Speed Adjustment
2-6. Speed adjustment Caution To adjust the cylinder’s operation speed, install a speed controller and slowly increase the speed until the desired speed is reached. Piston speed should be controlled gradually from low speed to the specified speed with a speed controller. -
Page 11: Mounting Of Optional Adjuster
2-8. Mounting of optional adjuster Caution ➀ Adjuster options are shipped together with the product. To correctly install the stroke adjuster, follow the steps below. ➁ The bolt length of the body mounting part and the table mounting part are different. Be aware that the hexagon socket head cap screws for the body mounting part, and the table mounting part of the adjuster on the extension end (AS,BS) are of different lengths. - Page 12 2. Body mounted part Thread Tightening torque size N･m Body M10x25 29.5～34.5 Stopper block Hexagon socket head cap bolt Note) To install the stopper block, first move it in the direction of the arrow until it is flush with the body, then secure it.
- Page 13 2. Body mounted part Thread Tightening torque size N･m M10x22 29.5～34.5 Stopper plate Hexagon socket head cap bolt Body Note) When installing the stopper plate, make sure it does not protrude from the table.
-
Page 14: Handling Of Optional Adjuster
2-9. Handling of optional adjuster ●Rubber stopper / Metal stopper Caution ➀ Do not use with a bolt other than the original adjustment bolt. Using a different bolt could result in looseness and damage due to impact forces etc. ➁ Tightening torque for the lock nut should be in accordance with the table on the right. Insufficient torque will result in a decrease in positioning accuracy. -
Page 15: Handling Of Products That Are Positioned Side By Side
2-10 Handling of products that are positioned side by side Caution ➀ Ensure a minimum spacing of 3mm when mounting product and product. If there is not sufficient space between the adjusters, the auto switch may malfunction. 3mm minimum spacing 2-11 Mounting of auto switch Caution Mounting precautions... - Page 16 ④ Refer to the table below for the appropriate installation position of the auto switch (when stroke end is detected). For actual setting, please check the operating condition of the auto switch before adjustment. (mm) Stroke A Auto switch model D-M9□/M9□W 76.5 66.5...
- Page 17 ⑤ Please refer to the figure below of the wiring and connection of the auto switch.
-
Page 18: Maintenance
3．Maintenance 3-1 Precautions on maintenance Caution Maintenance should be done according to the procedures of〝Operation Manual″. ① Wrong handling may result in breakage or malfunction of product. ② Dismantling of product and supply / exhaust of compressed air. properly provided, shut the power source of air supplied, and exhaust compressed air in the system. -
Page 19: Replacement Procedure Of Seal
Replacement Procedure of Seal Caution Do not disassemble the linear guide section of the air slide table. （replacement procedure） ① Remove the hexagon socket head cap screws that connect the end plate and table. Table Hexagon socket head cap screws for end plate mounting Thread size M8x1.25... - Page 20 ④ Remove the floating bushes B. ⑤ Remove the Circlips. (Use Circlip pliers.) ⑥ Remove the piston rod and head cap assemblies from the body. C retaining ring Head cap assembly Table Packing support Body C retaining ring Magnet Piston assembly Rod cover assembly Floating bush B End plate...
- Page 21 ⑦ Remove the seal supports. ⑧ Remove the seals from the rod cover, piston rod, and head cap assemblies. ⑨ Apply grease to the new O-rings, rod seals, and piston seals, and then insert the new seals. Head cap assembly Piston seal O-ring O-ring...
- Page 22 ⑩ Mount the rod cover assemblies and seal supports on the piston rod assemblies and insert them to the body. ⑪ Insert the head cap assembly into the body. ⑫ Mount the Circlips. (Use Circlip pliers.) ⑬ Install the floating bushes B on the piston rod assemblies. ⑭...
- Page 23 ⑯ Apply adhesive to the hexagon socket head cap screws. (See Note Below) ⑰ Tighten the hexagon socket head cap screws that connect the end plate and table to the proper tightening torque. Hexagon socket head cap screw for end plate mounting Thread size Tightening torque N・m M8x1.25...
- Page 24 Revision history Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 https://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. © SMC Corporation All Rights Reserved...
Need help?
Do you have a question about the MXQ32 X2600 Series and is the answer not in the manual?
Questions and answers