Subscribe to Our Youtube Channel
Related Manuals for Altinex MULTI-TASKER MT106-100
Summary of Contents for Altinex MULTI-TASKER MT106-100
- Page 1 MULTI-TASKER MANUAL PART NUMBER: 400-0096-004 MT106-100 SCAN REDUCER CARD FOR MULTI-TASKER USER’S GUIDE...
-
Page 2: Table Of Contents
7.3 SUMMARY OF COMMANDS....13 TROUBLESHOOTING GUIDE......13 8.1 LED IS NOT LIT ........13 8.2 LED IS BLINKING RED ......14 8.3 NO DISPLAY ........... 14 ALTINEX POLICY..........14 9.1 LIMITED WARRANTY/RETURN POLICY 14 9.2 CONTACT INFORMATION...... 14... -
Page 3: Precautions / Safety Warnings
• Any changes or modifications to the unit not appliances, or near any liquid. Exposure to expressly approved by ALTINEX, Inc. could void direct sunlight, smoke, or steam can harm the user’s authority to operate the equipment. internal components. -
Page 4: About Your Mt106-100
Impedance (terminated) Though this can easily be adapted to 5 BNC Input Sync Signal connectors for RGBHV using an ALTINEX VGA to Horizontal, Vertical TTL (+/-) RGBHV adapter cable. The composite video Impedance 10k Ohms outputs provided... -
Page 5: Description Of Mt106-100
MULTI-TASKER DESCRIPTION OF MT106-100... -
Page 6: Application Diagram
MULTI-TASKER APPLICATION DIAGRAM Application 1 Application 2... - Page 7 MULTI-TASKER Application 3: Internal View of the MT106-100...
-
Page 8: Installing Your Mt106-100
MULTI-TASKER Square brackets “[ ]” are part of the INSTALLING YOUR MT106-100 command. Step 1. Slide the MT106-100 into an available Use uppercase letters for all commands. slot in the Multi-Tasker™ Basic Enclosure in order to connect to the bus. Make sure After processing a command, an OK or ER that the MT106-100 Scan Reducer card string will be returned as feedback if "F"... - Page 9 MULTI-TASKER Example: default values and place the card in NTSC format. One MT106-100 card is in slot #2 of unit 3. 4. [ + ] or [ - ] Sending the command [VERC2U3] to the Multi-Tasker™ Basic Enclosure will yield the These commands allow the user to increase or following feedback: decrease the selected attribute value.
- Page 10 MULTI-TASKER 5. [HPOSnCi] - Set Value Command Format: [VPOSnCiUy] This command sets the Horizontal Position to = a value from 0 to 20 an absolute value. It also makes the Horizontal Ci = card ID (i = slot number) Position adjustment the active control. Uy = unit id (i = 0 to 9) (refer to the MT100-100 Command Format: [HPOSnCiUy] user’s guide for explanation)
- Page 11 MULTI-TASKER Example: also returns the status of the current Vertical Size. As the active control, it may be adjusted There is an MT106-100 in slot 2 of unit ID 3. using the [ + ] and [ - ] commands. Set the Horizontal Size to the value of 12 by Command Format: [VSIZECiUy] sending the command [HSIZE12C2U3].
- Page 12 MULTI-TASKER Zoom value. As the active control, it may be Command Format: [BRIGCiUy] adjusted using the [ + ] and [ - ] commands. Ci = card ID (i = slot number) Command Format: [QZOOMCiUy] Uy = unit id (i = 0 to 9) (refer to the MT100-100 Ci = card ID (i = slot number) user’s guide for explanation) Uy = unit id (i = 0 to 9) (refer to the MT100-100...
-
Page 14: Led Is Blinking Red
Solution 2. TEL: 714 990-2300 Solution 2: Turn the system OFF and then ON again. If there is still an error, see TOLL FREE: 1-800-ALTINEX Solution 3. WEB: www.altinex.com Solution 3: Call ALTINEX at (714) 990-2300. E-MAIL: solutions@altinex.com...
Need help?
Do you have a question about the MULTI-TASKER MT106-100 and is the answer not in the manual?
Questions and answers