Subscribe to Our Youtube Channel
Related Manuals for ELECANE TC316G
Summary of Contents for ELECANE TC316G
- Page 1 Bark Collar Product Manual Model TC316G Please Read This Manual Carefully Before Use CUSTOMER SUPPORT: support@elecane.com www.elecane.com...
- Page 2 COMPONENTS ELECANE Bark Collar with Belt Type-C Charging Cable User Manual...
-
Page 3: Product Overview
PRODUCT OVERVIEW ON/OFF button (long press) Sensitivity button Mode button(short press) Test the collar by blowing into the hole Vibration probes Type-C charging port Beep Vibration Beep + Vibration Standby indicator light Battery charge level display Sensitivity display... -
Page 4: Product Introduction
PRODUCT INTRODUCTION Our bark collar is designed to gently and effec- tively prevent excessive barking in your dog. Using humane methods, it applies a beep, vi- bration, or a combination of both to modify be- havior without any shocks. This advanced model features dual sensors with a built-in microphone and motion detector. - Page 5 CHARGING INSTRUCTIONS The device has a built-in 260 mAh recharge- able battery. Please charge the collar before use or when a low battery warning is displayed. Use only the specified charger with a rating of 5 V and current between 500 - 1000 mA to charge the collar.
- Page 6 Sensitivity Level Adjustment: Press the “S” button to adjust 0-7 sensitivity lev- els. The highest level is 7. Please set suitable sensitivity level based on your dog’s barking. If the barking is loud, could decrease the sen- sitivity level. If the barking is loud, you could decrease the sensitivity level.
- Page 7 Press the “S” button to adjust the sensitivity to level 0, then blow into or shout towards the microphone hole on the back of the collar. ELECANE When the bark collar is triggered, it will for 1 second, then vibrate for 1 second, the mode...
- Page 8 HOW THIS BARK COLLAR WORKS There are 7 progressive correction levels in a cycle under each anti-barking mode, as shown below. The working sequence under beep mode: 1 st: 0.8 s beep, the icon ( ) flashes for 0.8 s 2 nd: 1.6 s beep, the icon ( ) flashes for 1.6 s 3 rd: 2.4 s beep, the icon (...
- Page 9 The working sequence under beep+vibration mode: 1 st: 0.8 s beep + vibration, the icon ( ) flashes for 0.8 s 2 nd: 1.6 s beep + vibration, the icon ( ) flashes for 1.6 s 3 rd: 2.4 s beep + vibration, the icon ( ) flashes for 2.4 s 4 th: 3.2 s beep + vibration, the icon ( ) flashes for 3.2 s...
- Page 10 HOW TO ADJUST THE BELT lf the belt is too long, you can cut off extra parts. Push and pull the belt or slide the adjuster to adjust the collar length. Tips for Training Your Dog with the Anti Bark Collar Please don’t leave your dog unat- tended when you first start training with the collar.
- Page 11 Cautions! • Do not allow your dog to chew the collar. Prevent your dog from scratching or clawing at that casing. • This device is made of plastic and electronic compo- nents that are not digestible. Consult your vet immediate- ly if your dog swallows any parts of this product.
- Page 12 FAQs Q: The collar keeps going off or it’s activated eas- ily even when my dog shakes its head. A1: The sensitivity level is too high. Reduce it by pressing the “S” button. A2: The collar is not tight enough. Please tight- en the collar.
- Page 13 Unlock Exclusive Perks! Scan the QR code for instant access to prod- uct guides, VIP support, special offers, and a FREE e-book. Scan the QR Code or Visit: http://qr.elecane.com/G316...
Need help?
Do you have a question about the TC316G and is the answer not in the manual?
Questions and answers
The green standby indicator is flashing and I can’t get it to do anything else, what do I do?
If the green standby indicator on your ELECANE TC316G is flashing and the device is unresponsive, it likely means the device is about to power off automatically. Wait 30 seconds for it to shut down, then press and hold the “M” button for 2 seconds to power it back on.
This answer is automatically generated