Subscribe to Our Youtube Channel
Related Manuals for Aqua SALT+
Summary of Contents for Aqua SALT+
- Page 1 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL ENGLISH AQUA SALT For other languages please visit ADSP7000753 rev. 5.0 09/07/2019 1/51...
- Page 2 AQUA SALT KEYPAD Switch on or off your AQUA SALT with the ON/OFF key. Press and hold Enter →You will switch to the Password Menu. Default password: 0000 → Press and hold Enter → You will switch to the Installer Menu.
- Page 3 AQUA SALT KEYPAD Switch on or off your AQUA SALT with the ON/OFF key. Press and hold Enter →You will switch to the Password Menu Default password: 0000 → Press and hold Enter → You will switch to the Installer Menu Press F to scroll the Menu down to Pool Settings →Press Enter to access the submenu...
- Page 4 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH ADDENDUM – ADDITION OF SALT NOTE FOR AQUASALT DEVICE WITH ELECTROLYTIC CELL TO 200 mc PROCEDURE FOR ADDITION OF SALT IN THE BALANCE TANK OR IN SKIMMER 1. CHECK THE NEEDED QUANTITY OF SALT 2.
-
Page 5: Table Of Contents
1.1 Warnings ............................7 1.2 Reference standards ........................... 7 1.3 Electrical Features ..........................7 1.3.1 Performance ................................8 1.3.2 Electrical techniques ............................... 8 2 Aqua salt description ........................8 2.1 Functioning ............................8 2.2 The device ............................9 2.3 Other operating modes........................9 2.4 Chlorine generator models ....................... - Page 6 Salt chlorine genera ENGLISH 8 Software ............................ 37 8.1 HOW TO CONNECT THE DEVICE TO THE PC AND CONFIGURE THE SYSTEM .......... 37 8.2 AQUA SALT SOFTWARE PRESENTATION ..................37 8.3 MENUS............................. 38 8.4 ICONS............................... 38 8.5 TABS ..............................40 8.6 PROGRAMME KEYS ..........................
-
Page 7: Introduction
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH AQUA SALT is a multi-function chlorine generator that generates 1 Introduction disinfectant active chlorine directly from the salt of the pool. The system is designed for small and medium pools, up to 200 m Please read the label on the product and respect the following points: At the receipt, make sure that generator's packaging and components are not broken or damaged. -
Page 8: Performance
(common cooking salt). This way, you will no longer have to buy, 2 Aqua salt handle or store the common chemicals for pools (sodium hypochlorite, trichloro, dichloro). You will only have to add a certain... -
Page 9: The Device
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH ✓ Proportional: The generator reads the redox potential or the ppm of chlorine present in the pool. In the case of the redox potential, the installer will have to determine the correspondence between pH - redox and the ppm of chlorine required (Ex: 7.2 pH - 650 mV... -
Page 10: Chlorine Generator Models
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH ✓ THER MODES There are other operating modes related to system's restart, first installation or maintenance: • Superchlorination (boost): When this work mode is on, the generator stops its internal adjustments and starts working at 100% for 12 hours. -
Page 11: Installation
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH General instructions The installation of the generator must be done as follows: • In vertical position, with an inclination below +/-15°. • Far from heat sources, in dry places, at a temperature between 0 °C and 45°C. -
Page 12: Electrolytic Cell And Control Box Installation
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH At this point, it is necessary to connect the electrolytic cell to the control box by connecting flow 3.1.3 sensor/pressure, temperature probe and the part that provides voltage to the plates, as indicated in... -
Page 13: Ph, Rx, Clj Model Installation
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH The sample installation diagram below refers to pH, pH/Redox, pH/ClJ chlorine generators. To fasten, install and connect the electrolytic cell and control box, please follow the instructions provided for the standard model. -
Page 14: Installation Example
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH 3 Connector overview. Lower part of the control box 3.2.2 The sample installation diagram below refers to the pH, pH/Rx, pH/ClJ models. Installation example Number 12 in picture 9 indicates the... -
Page 15: Hydraulic Connections
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH To properly install the chlorine generator in your system, we recommend to create a deviation on which to place the electrolytic cell, as indicated in the diagram below. However, installing the generator on the main pipeline does not affect the its correct functioning. -
Page 16: Programming Procedure
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH To get the best results from your chlorine generator, programme its activity and set the values of its parameters. To do so, the system comes with a user interface equipped with: 4 Programming •... -
Page 17: The Menus
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH UPERCHLORINATION KEY AND Boost key activates superchlorination. The generator stops its internal adjustments and starts working at 100%, for 12 hours. At the end of the superchlorination process, the generator goes back to the set work mode. Green LED steady on if superchlorination is active. - Page 18 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH The first section shows two columns: the left one shows the state of the device, the right one shows the amount of chlorine generated (in mV or ppm) or the set chlorine percentage. You can modify the % with the keys only if the state is Work, Start-Up and if the shutter is open.
-
Page 19: Password Menu
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Chlorine cell replacement * Cell check Redox Flow & Pressure Chlor Enter Stop phase Confirm? Yes/No Average salinity time left Enter estimated Reset average salinity Confirm? Yes/No clock phase instant... -
Page 20: Pool Settings Menu
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Last modification Pool Comunication settings System Alarms settings* Chlorine/Redox Programming * calibration* Calibration* Last Pool settings Chlorine/Redox System settings modification calibration date It shows the date of the last Switches... -
Page 21: System Settings Menu
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH This menu manages the general operation settings of the chlorine generator, like unit of measurement of 4.5.2 temperature and salinity, current date and time, clock type and others. System •... -
Page 22: Redox Probe Calibration Menu
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH after 5 seconds, it displays the value of the measured chlorine (uncalibrated) from the probe and expressed in ppm. If you press the Enter key returns to the value of the previously measured chlorine. Use the Up and Down keys to change this value to the value measured with the photometer (DPD method). -
Page 23: Programming Menu
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Wait without touching the probe or its cable for at least 60 seconds, until the value read is stabilized, then press Enter. At the end of the countdown or after pressing Enter, the pH value of the solution and the (4.01) -
Page 24: Alarms Menu
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Chlorine (base) Chlorine set Chlorine Rx set point point (WM) It allows you to visualize and change the percentage of It allows you to view and Visualize and change the... - Page 25 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Select how to connect the control box of the device to the PC. You can choose among: Connection type • RS232 • Bluetooth Select the address within the range 1-99 used in the Modbus Modbus communication protocol.
-
Page 26: Alarms
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH The alarm signal with the highest priority will be visible alternately 5 Alarms to the main section of the User menu, while the corresponding Led (Alarm or Maintenance Led) will be enabled for all menus 1) The High temperature alarm, which cannot be disabled from the alarms menu, goes off if temperature read is higher than 60 °C. -
Page 27: Cell Replacement Pre-Alarm
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH The alarm activates when the generator worked for a longer time than the value set under “Cell Replacement” in the Alarms Menu. The time for the replacement of the electrolytic cell can be set within a range of 5000-20000 hours, at Cell replacement intervals of 1000 hours. - Page 28 AQUA SALT control 5. Get off locking ring and o-ring Unscrew three 7. Remove titanium plates. 8. In a bowl put 9 parts of from tre cell.
-
Page 29: Returning The Product To The Manufacturer's After Sales Service
The manufacturer warranty covers the devices for 12 months after the delivery date. The control system of the Aqua Salt (control unit) is ensured, however, for 36 months. Warranty Within these terms, the manufacturer undertakes to supply for free the spare parts that, according to... -
Page 30: Annex B Dimensions
AQUA SALT PROTECTIVE CAP FEMALE PLATE TITANIUM PTEPL050106F TITANIUM PLATE HOLDER RANGE ELECTRODE L 50 - AQUA SALT PTEPL100107F TITANIUM PLATE HOLDER RANGE ELECTRODE L 100 - AQUA SALT PTEPL150108F TITANIUM PLATE HOLDER RANGE ELECTRODE L 150 - AQUA SALT... -
Page 31: Annex Dmenu Map
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH User Menu Annex D Chlorine MENU MAP cell replacement * Redo Cell check * Flow & Pressure Chlor Average time left salinity estimated clock phase instant salinity phase time left... -
Page 32: System Settings Menu
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Installer Menu Last modification Pool Comunication settings System Alarms settings* Chlorine/Redox calibration* Programming * Calibration* Pool Settings Menu Pool capacity Generator Cover filter operation System Settings Menu Restore Parameters Salinity... - Page 33 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Dip the probe in the water Set chlorine Waiting read Chlorine chlorine ADSP7000753 rev. 5.0 09/07/2019 33/51...
-
Page 34: Programming Menu
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Redox Probe Calibration Menu Dip the probe in the water Probe Waiting Quality Rx 475 pH Probe Calibration Menu Dip the probe in the water Probe Waiting Quality pH 4.01 pH 7.00... -
Page 35: Annex E Elements Of Water Chemistry And Optimal Conditions Of Pools
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Alarms Menu Ice alarm Cell replacement Cell Service alarm reset Cell Service Cell alarm reset Replacement Communication Menu Connection Type Modbus Address A chemically balanced water is fundamental to avoid problems like frequent pH corrections, metallic part corrosion or pipe fouling. -
Page 36: Annex F Things To Know About Your Pool
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH The first thing you have to know about your pool is its volume. To calculate the volume of your pool, follow the formulas below depending on the shape of your pool:... -
Page 37: Software
MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH 8 Software Manual for the AQUA SALT remote control software 8.1 HOW TO CONNECT THE DEVICE TO THE PC AND CONFIGURE THE SYSTEM Connect AQUA SALT to the PC through the serial ports with a serial cable as shown below: You can use an RS232→USB adaptor if the PC has no serial ports. -
Page 38: Menus
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH 8.3 MENUS The File Menu includes the typical sections: new, open to open the files where the working parameters of your generators are saved; save, save as, exit to close the application. - Page 39 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH • Click on Actions → Bluetooth Radio On → Searching devices. • The devices found will appear. • Double click on the selected device for quick connection. • Confirm the connection request and insert the password.
-
Page 40: Tabs
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH 8.5 TABS ✓ The USER tab controls some operating parameters of your chlorine generator Device state Last modification to the parameters Alarms Device state Last modification date Flow Indicates the current state of the... - Page 41 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Generator operation Salinity level Temperature sensor Indicates the work mode of the Indicates if the level of salinity is Indicates the state of the "Temperature generator (Internal timers, External sufficient or insufficient.
- Page 42 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Flow & Pressure filter Work mode Indicates or sets the duration of flow Indicates or sets the pH Display & pressure filter, i.e. the minimum work mode (Acid, Alkaline). time must be present to be recorded.
- Page 43 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH Indicates or sets the enabling of the "Insufficient Indicates or sets the enabling of the "Temperature probe" alarm production" alarm (On, Off). (On, Off). Excessive salt alarm enabling Temperature probe alarm enabling Indicates or sets the enabling of the "Excessive salt"...
-
Page 44: Programme Keys
If restoration is not possible through the repair and / or if the latter proves prohibitively expensive compared to the value of the product, determined at the discretion of the manufacturer, Aqua will replace the equipment at the customer end, leaving unchanged the deadline and terms guarantee referred to in the original contract and evidenced by tax document issued at the time of purchase. - Page 45 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH RULES AND RESPONSIBILITIES FOR REPAIRS. PERIOD OF WARRANTY • For the warranty to be valid and operative, the customer must show documentation showing the date of purchase of the product, its specific identification and type. To meet this need will be sufficient to show, along with the original warranty for the product, a document valid for tax purposes (transport document, invoice, receipt) certifying the date of purchase, model and the purchase price.
-
Page 46: Maintenance Regestry
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH 10 Maintenance regestry Registry of the verification and maintenance Number D ESCRIPTION OF AINTENANCE OURS IGNATURE THE ACTIVITIES OF DATE WORKED MAINTENANCE VERIFICATION AND DATE MAINTENANCE Etichetta ADSP7000753 rev. 5.0... -
Page 47: Pressure Switch Assembly
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH 11 Pressure switch assembly ADSP7000753 rev. 5.0 09/07/2019 47/51... - Page 48 AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine generator ENGLISH ADSP7000753 rev. 5.0 09/07/2019 48/51...
-
Page 49: Connections With Other Versions
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH 12 Connections with other versions ADSP7000753 rev. 5.0 09/07/2019 49/51... -
Page 50: Download Software
AQUA SALT MAINTENANCE AND INSTRUCTION MANUAL Salt chlorine genera ENGLISH 13 Download software ADSP7000753 rev. 5.0 09/07/2019 50/51... - Page 51 For other languages please visit ADSP7000753 rev. 5.0 09/07/2019 51/51...
Need help?
Do you have a question about the SALT+ and is the answer not in the manual?
Questions and answers