Related Manuals for Greiner Vibrograf SL2
Summary of Contents for Greiner Vibrograf SL2
- Page 1 Operating instructions Belt grinder with lapping disc Version: 02-2024-EN Date: 07.08.2024 Manufacturer: Greiner Vibrograf AG Mittelstrasse 2 CH-4900 Langenthal...
-
Page 2: Table Of Contents
GENERAL INFORMATION .......................... 4 ................... 4 NFORMATION ON THESE OPERATING INSTRUCTIONS ......................... 4 USTOMER SERVICE INFORMATION ............................4 NTENDED USE ............................ 4 INTENDED USE SAFETY INSTRUCTIONS ..........................5 ..............................5 YMBOLS ......................5 AFETY INSTRUCTIONS AND WARNINGS ..........................5 IDDING INSTRUCTIONS .......................... - Page 3 ............................27 PARE PARTS ..........................27 RIGINAL ACCESSORIES 9.2.1 Grinding table (grinding belt) Art. no 36600 ................... 27 9.2.2 Grinding table (lapping) Art. no 36700 .................... 27 9.2.3 Hand piece for SL2 Art. No. 40200 ....................28 www.greinervibrograf.ch/Lapidiergeraete/Zubehoer SL2 ................28...
-
Page 4: General Information
1.3 Intended use The SL2 belt grinder with lapping disc is used for grinding and lapping watches. Other uses are not permitted. The installation and operating conditions specified in these operating instructions must be strictly observed. 1.4 Non-intended use... -
Page 5: Safety Instructions
2 Safety instructions 2.1 Symbols Read through the operating instructions General information 2.2 Safety instructions and warnings General danger Warning of electrical voltage Warning of hand injuries 2.3 Bidding instructions Wear hearing protection and eye protection! This sticker indicates that hearing protection and safety goggles with shatter-proof clear lenses must be worn when working with the appliance. -
Page 6: Emergency Stop System
The SL2 belt grinder with lapping disc is equipped with an EMERGENCY STOP switch. This is located at the top of the housing. It is used to quickly bring the mechanical parts of the SL2 to a standstill in the event of danger or to avert danger. -
Page 7: Function, Installation And Commissioning
When extending the cable, ensure that it is in perfect condition and ensure that it can withstand the current before use. 3.4 Commissioning Switch on the SL2 using the mains switch at the bottom rear (on the back of the appliance). -
Page 8: Operation
4 Operation 4.1 Screen The SL2 has a touchscreen. All functions and settings are carried out via this screen. After starting up the SL2, the following main menu is always displayed: 4.2 Settings 4.2.1 Start / Stop The Start / Stop button is located at the top right of the display. First select the desired program (1 - 4) and briefly press the start button. -
Page 9: Speed Setting
4.2.2 Speed setting The speed can be changed very easily directly using the central rotary knob. As follows: • Faster in a clockwise direction • Slower in anti-clockwise direction The speed is immediately adjusted to the set speed and shown on the display. It is also possible to use the preset speeds. -
Page 10: Belt Position
1. Distance to the sanding belt Loosen the front knurled screw, position the table and tighten again 2. Height of the worktable Loosen the clamping lever anticlockwise Move to new height position Tighten the clamping lever again (clockwise) 3. Tilt angle of the worktable Release the clamping lever on the outside left Use the large, knurled screw to set the desired working angle. - Page 11 Turn the strap tensioning screw (no. 3) until the strap tensioner is slackened (3.2) and the strap is loose 3.1 Tensioned belt tensioner 3.2 Belt tensioner untensioned 3. In this position of the belt adjustment head, the sanding belt can be both removed and mounted again.
-
Page 12: Changing The Lapping Disc
4.4 Changing the lapping disc Press the locking button on the top of the housing and simultaneously turn the lapping disc until the button engages. Hold down the button and loosen and unscrew the central hexagon socket screw (tool no. 5). The lapping disc can now be replaced. - Page 13 The lapping table can be adjusted in 3 ways. Namely: 1. Distance to the lapping disc (X-axis) 2. Angle to the lapping disc 1. Distance to the lapping disc (X-axis) Loosen, adjust and retighten the front knurled screw. 2. Angle to the lapping disc Release the clamping lever on the outside left Adjust the working angle with the knurled screw.
-
Page 14: Adjusting The Guide For The Hand Piece
4.6 Adjusting the guide for the hand piece Loosen both hex screws on the left and right, adjust in the grid and tighten again. -
Page 15: Display Adverts
4.7 Display adverts 4.7.1 Control panel Programmes: 4 standard programmes are preset. The programmes can be individually adapted (4.7.7). Processes: The nominal speed is displayed here. The speed can be adjusted manually using the rotary knob or assigned to a programme via screen (4.7.7). Settings: 4.7.2 Language... -
Page 16: Date Time
4.7.3 Date Time Basic setting for date and time via scroll-up/down menu. Set and confirm with SAVE. 4.7.4 Display The parameters for the display can be set here. These are brightness, time until the display switches off and the screen saver appears, and the brightness of the screen saver. -
Page 17: Service
4.7.5 Service Press and hold the SERVICE button for 2 seconds, the following screen appears: The user and password are only accessible to authorised users. However, every user (level 1) can call up the following information without a password by double-clicking the Enter key: SW version HW version... -
Page 18: Light And Extraction
4.7.6 Light and extraction Light and suction, if available, can be switched on and off directly using the two buttons. When light or suction is activated, the field frame appears in yellow. The 2 connection sockets (Schuko) for light and extraction are located on the rear of the appliance. Max. -
Page 19: Changing Programmes
4.7.7 Changing programmes The preset programme names can be overwritten as required. To do this, simply press the corresponding programme button for longer than 2 seconds. The existing text can now be renamed. Finally, confirm with SAVE. The nominal speed for the selected programme can be changed by pressing the speed button for at least 2 seconds. -
Page 20: Technical Data
5 Technical data 32000 SL2 (230V) Item numbers 32100 SL2 (115V) 230 V / 50 Hz Mains connection 115 V / 60 Hz Engine performance: 0.5 kW Power consumption: max. 2.2 A Speed: 150 - 2000 rpm, variable speed Belt speed:... -
Page 21: Dimensions
5.1 Dimensions... -
Page 22: Device Overview
5.2 Device overview Protective cap for sanding belt Locking motor Sanding belt Rotary knob, rotary switch Tensioning pulley Display Tensioner fixing Lapping disc Belt adjustment screw Adjustable lapping table (accessory) Tensioner adjustment wheel Guide rod for quill Adjustable grinding table (accessory) Base plate EMERGENCY STOP Engine... -
Page 24: Service And Maintenance, Faults
6 Service and maintenance, faults 6.1 Service and maintenance The SL2 sanding and lapping machine is practically maintenance-free. Only the sanding belts and discs should be checked regularly and replaced if necessary. The appliance should also be kept as clean as possible to ensure that it functions properly. -
Page 25: Declaration Of Conformity
7 Declaration of Conformity... -
Page 26: Waste Disposal
8 Waste disposal We do our utmost to keep recycling costs to a minimum in order to pass on the resulting benefits to our customers and society as a whole. For this reason, if you ever have to part with this appliance, please do not dispose of it in the rubbish bin, but send it to the appropriate collection centre for old electrical appliances. -
Page 27: Appendix
9 Appendix 9.1 Spare parts 9.2 Original accessories Important! With the exception of the sanding belts and sanding discs, only use original accessories with the appliance. 9.2.1 Table for grinding belt Art. no 32020 9.2.2 Table for lapping disc Art. no 32030... -
Page 28: Hand Piece For Sl2 Art. No. 40200
9.2.3 Hand piece Art. No. 32040 See also on our website under: www.greinervibrograf.ch/Lapidiergeraete/Zubehoer SL2...
Need help?
Do you have a question about the SL2 and is the answer not in the manual?
Questions and answers