Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Fluke VIBROTECTOR VIB 5.721
Summary of Contents for Fluke VIBROTECTOR VIB 5.721
- Page 1 Vibration Transmitter VIBROTECTOR ® Installation and Operation...
- Page 3 VIBROTECTOR ® Vibration transmitter Installation and Operation Type: VIB 5.721 Edition: Rev. 1 07.2024...
- Page 4 This manual is the intellectual property of Fluke Corpora- tion. It may not be electronically or mechanically duplicated, distributed, modified, transferred, translated into another language or changed in any way, either in its entirety or in part, without the express written permission of Fluke Cor- poration.
-
Page 5: Table Of Contents
Contents Contents 1. Important notes Before you begin Intended use EU Declaration of conformity Symbols Information on disposal 2. Scope of delivery Standard Accessories 3. Technical data VIBROTECTOR transmitter type VIB 5.721 Dimensions and mounting heights 4. Mounting Mounting VIBROTECTOR Adhesive mounting 5. -
Page 6: Important Notes
VIBROTECTOR may only be used according to the specifica- tions made in the operating instructions. EU Declaration of conformity Fluke hereby declares that VIBROTECTOR is in conformity with the applicable European directives. The full text of the EU declaration of conformity is available at the following Internet address: www.pruftechnik.com... -
Page 7: Scope Of Delivery
Scope of delivery 2. Scope of delivery Standard VIBROTECTOR, sensor frequency range 10 hz to 1 khz: VIB 5.721 Accessories - Adapter for adhesive mounting: VIB 3.433 - Sensor cable, PUR: VIB 309007, VIB 5.745* * more details can be found in section Connection cables. Further accessories and technical details can be found in the product catalogue. -
Page 8: Technical Data
Technical data 3. Technical data VIBROTECTOR transmitter type VIB 5.721 Output signal Current intensity level (4-20mA) Measurement range ≤ 20 mm/s Measurement accuracy ± 5% Nominal 80Hz at 22°C Frequency range ±5% 10 Hz to 1 kHz Frequency response Temperature range -25 °C to 120 °C (-13 °F to 248 °F) Power supply 18 to 30 V DC (±5%), loop power... -
Page 9: Dimensions And Mounting Heights
Technical data Shock limit < 50 kms Weight 100 g (3.53 oz) Dimensions and mounting heights in mm... -
Page 10: Mounting
Mounting 4. Mounting The frequency response and dynamic range of an acceler- ometer can be greatly influenced by the installation. Poor coupling to the measurement location can adversely affect the signal and restrict the frequency range. In principle the accelerometer needs a non-positive, contact resonance- free and rigid fastening to the measurement location, espe- cially for measurements with high frequencies. -
Page 11: Mounting Vibrotector
Mounting Mounting VIBROTECTOR Tools required: - Hand-held drill - Drill bits with depth gauge (3.5 mm /6.8 mm) - Countersink bit for flush mounting - M8 thread tap - Torque wrench with 22mm (55/64”) hex socket - Compressed air for cleaning out the hole 1. - Page 12 Mounting 3. Clean and smooth the area around the mounting hole, and then roughen the surface with abrasive paper (type 220). 4. Clean the contact surfaces of the sensor and machine with solvent. 5. Allow the contact surfaces to dry and then apply a thin film of screw paste (LOCTITE 243) to improve signal transmission.
-
Page 13: Adhesive Mounting
Mounting Adhesive mounting Parts required: - Adapter for adhesive mounting, type: VIB 3.433 Tools required: - File - Hand-held drill and drill bit with depth gauge (3.5 mm) - Compressed air for cleaning out the hole VIB 3.433 - Two-component adhesive (e.g. WEICON HB 300) If the machine is put into operation before the adhesive has hardened, the bonding may disintegrate. - Page 14 Mounting 2. Flattening and roughening: Sand down any paint on the mounting surface to bare metal (diameter at least 30 mm). Level out the mounting surface if necessary. Roughen the mounting surface with a file (filing a few grooves in a diamond pattern provides greater adhesion.) Option: Bore hole for centering pin.
- Page 15 Mounting 7. Mount VIBROTECTOR Remove the M8 threaded bolt from the sensor if neces- sary and screw the sensor onto the adapter. Do not ex- ceed permitted torque (3 - 7 Nm!) VIBROTECTOR mount- ed on adapter for adhesive mounting...
-
Page 16: Electrical Connection
Electrical connection 5. Electrical connection VIBROTECTOR is connected to the monitoring system by means of a 2-pole cable. On the transducer side, the cable is equipped with a 2-pin MIL plug. (-/shield) (+/signal) Plug pin allocation Connecting the cable with the accelerometer Push the female connector onto the sensor and tighten by hand. - Page 17 Electrical connection Junction boxes of metal must be electrically insulated when they are mounted. Note Junction box - VIB 6.776 Material: ABS plastic Environmental protection: IP65 Dimensions in mm...
-
Page 18: Installing The Connection Cable
Electrical connection Installing the connection cable Use metal conduit or protective tubes to protect the cable from mechanical damage as well as to safeguard the in- crease of EMC. Connection cables may not be installed in parallel to energy lines. If this is not possible, the minimum distance should be 1 meter. -
Page 19: Connection Cables
Connection cables 6. Connection cables Shielded 2-pole cables are used for signal transmission. VIB 3.570-L Sensor cable, partly pre-assembled, PUR sheath, MIL plug- in connector (2p straight aluminum alloy), IP68, L: Available length in meters (6, 12, 20, 30, 40, 60). VIB 309007-L Sensor cable, partly pre-assembled, PUR sheath, MIL plug- in connector (2p straight aluminum alloy),... -
Page 20: Cable Type
Connection cables Cable type Cable type VIB 90061 is installed in the connection cables. This cabel type ... • is resistant against mineral oil and hydraulic fluid • is flame-retardant / halogen free (IEC 60332-1-2) • is notch resistant • is insensitive against electrical interference •... - Page 21 Connection cables...
- Page 22 Rev. 1 07.2024 Fluke Deutschland GmbH 85737 Ismaning, Germany www.pruftechnik.com...
Need help?
Do you have a question about the VIBROTECTOR VIB 5.721 and is the answer not in the manual?
Questions and answers