Table of Contents
Advertisement
USE ONLY PITCHING MACHINE BASEBALLS
DO NOT USE HIGH SEAM REAL BASEBALLS
In tro duc tion
This manual con tains im por tant in for ma tion con cern ing the pro per use and care of your
HomePlate machine. Please read completely before operating your HomePlate machine.
Unpacking HomePlate Ultimate
To remove the HomePlate machine from the
packing carton, attach one or more of the legs
by sliding the upper part of the leg into the leg
base, and tightening the winged clamp screw
clockwise. Then lift the machine slightly by
the leg, and roll the machine out of the box.
Check for shipping damage
Even though your machine may appear un -
da ma ged, it is pos sible for inter nal parts to be
dama ged even if the exter nal case is un da ma-
ged. If your machine is dama ged, con tact Sports
Tutor im me diately at 1-800-448-8867.
HomePlate
Ultimate
OWNER'S MANUAL
FOR BEST RESULTS:
or LOW SEAM BASEBALLS
What's Inside
Operating HomePlate
Programming HomePlate
Hand-Feed Model
Page
2
2
2
3
3
4
6
6
6
6
6
7
8
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Sports Tutor HomePlate Ultimate
Summary of Contents for Sports Tutor HomePlate Ultimate
-
Page 1: Table Of Contents
In tro duc tion This manual con tains im por tant in for ma tion con cern ing the pro per use and care of your HomePlate machine. Please read completely before operating your HomePlate machine. Unpacking HomePlate Ultimate What’s Inside Page... -
Page 2: Important Warnings
Transporting HomePlate Ultimate CAUTION: Due to the weight of the HomePlate machine we recommend that two people be used to tip the HomePlate machine into the transport position as shown in the picture below left. - Page 3 Operat ing the HomePlate Ultimate machine SET-UP. Posi tion the HomePlate machine on the front half of the pitcher’s mound, or approximately 55 feet away from the plate (corresponding to a pitcher’s release point). Manually point the machine to pitch towards the plate. Adjust the tripod legs to the desired height, and also adjust them so the top and bottom of the case looks level to the ground.
-
Page 4: Control Panel
Control Panel 1) TYPE OF PITCH - Push the button for the pitch that you want. You cannot mix right-hand- ed and left-handed pitches in the same program. For instance, if you already have a right-hand- ed curve or slider stored in a program and you try to push the buttons for a left-handed curve or slider, the left curve and left slider indicator lights flash as a warning, and will not be selected. - Page 5 4) STORE & DELETE - When you have the Create-A-Pitch controls set to the pitch you want, push STORE to store that pitch in a memory location. Pushing STORE replaces any previously stored pitch in the selected memory location with the current pitch. Push DELETE to remove a pitch from the selected memory location.
-
Page 6: Batter's Indicator Lights
A1, A2, F3, F4, F5, H3, H4, H5, L3, L4, L5. If an error message is displayed, turn the machine off, wait ten seconds, then turn the machine on again. If the error message still occurs, please call Sports Tutor or your distributor for service. Remote Con trol (Optional) The hand-held remote control unit plugs into the remote jack located in the ball feed section of the control panel. -
Page 7: Warranty
Limi tation of in ci den tal or con se quen tial damages Sports Tutor is not res pon sible for any in ci den tal or con se quen tial damages of any kind. Our lia bi lity is limi- ted to the repair or replace ment, at our option, of a defec tive pro duct. - Page 8 HOMEPLATE ULTIMATE ONE-YEAR EXTENDED WARRANTY WHAT IT COVERS The HomePlate Ultimate extended warranty covers parts only under the same terms as the original HomePlate warranty, excluding the throwing wheels. LENGTH OF EXTENDED WARRANTY The extended warranty period is one additional year at a price of $300.
Need help?
Do you have a question about the HomePlate Ultimate and is the answer not in the manual?
Questions and answers
My HomePlate machine has been acting up and showing an error code after running for about 10/15 mins. Showing F3 error code. Any help would be great. Machine is from around 2012. Thanks.
Looking how the wires reconnect to the off an on switch 1 White 2 Black