Related Manuals for IBASE Technology AGS101T
Summary of Contents for IBASE Technology AGS101T
- Page 1 AGS101T Advanced Gateway & Ultra-Compact Fanless System User’s Manual Version 1.0 (July 2023)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”).
- Page 3 0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) AGS101T User Manual...
- Page 4 You are not suggested to disassemble, repair or make any modification to the device. Disassembly, modification, or any attempt at repair could generate hazards and cause damage to the device, even bodily injury or property damage, and will void any warranty. AGS101T User Manual...
- Page 5 Software in use (such as OS and application software, including the version numbers) 3. If repair service is required, please log in to the RMA system of the website or contact your distributor or sales representative for assistance. AGS101T User Manual...
-
Page 6: Table Of Contents
General Information ..............1 Introduction ..................... 2 Features ....................2 Packing List .................... 3 Optional Accessories ................3 Specifications ..................4 Product View – AGS101T ............... 6 Dimensions –AGS101T ................8 Chapter 2 Hardware Configuration ............9 Installations ................... 10 2.1.1 Memory Installation / Replacement ......... - Page 7 Advanced Settings ................44 Chipset Settings ..................56 Security Settings ................... 59 Boot Settings..................63 Save & Exit Settings................64 Appendix ...................... 65 I/O Port Address Map ................66 Interrupt Request Lines (IRQ) ............... 68 Watchdog Timer Configuration .............. 69 AGS101T User Manual...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Optional Accessories • Specifications • Product View • Dimensions... -
Page 10: Introduction
1.1 Introduction The AGS101T embedded computer is an ultra-compact fanless system AGS101T integrating the Intel Atom® x6000E Series processors (code- named Elkhart Lake) that deliver up to 4 cores with 40% increase in CPU performance and improved graphics when compared with previous versions. -
Page 11: Packing List
DIN Rail Bracket 1.4 Optional Accessories IBASE provide optional accessories as follows. Please contact us or your dealer if you need any. • DC-In Power Adapter • Power Cord • WiFi Antenna Kit • 4G/LTE or GPS Antenna Kit AGS101T User Manual... -
Page 12: Specifications
Aluminum & steel, silver • Mounting Desktop mount / Wall mount (wall mount kit included) • DIN rail mount Dimensions 190 x 52 x 110 mm (W x H x D) Certificate CE / LVD / FCC Class B (pre-scan) AGS101T User Manual... - Page 13 Non-operating: 3 Grms / 5 ~ 500Hz (Random operation) Shock With MIL-STD-810G • Operating: 30 g / 11 ms duration • Non-operating: 40 g / 11 ms duration All specifications are subject to change without prior notice. AGS101T User Manual...
-
Page 14: Product View - Ags101T
1.6 Product View – AGS101T Front View Name Name CN1: DVI-I Port CN6: USB 2.0 Ports CN2: HDMI Port DC In Gigabit LAN Ports DC In Power Input CN5: USB 3.1 Ports Antenna Holes AGS101T User Manual... - Page 15 Oblique View Remarks: Two Nano SIM card slots are located on the right side. Side View Remarks: Aside from the antenna hole, the picture above shows the following: CN7：2 in 1 Audio Jack (Line-out/Line-in) CN8：COM1 Connector CN10：COM2 Connector AGS101T User Manual...
-
Page 16: Dimensions -Ags101T
–AGS101T 1.7 Dimensions Unit: mm AGS101T User Manual... -
Page 17: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration The information provided in this chapter includes: • Installations • Information and locations of connectors... -
Page 18: Installations
2. Gently push the module in an upright position until the clips of the slot close to hold the module in place when the module touches the bottom of the slot. To remove the module, press the clips outwards with both hands, and the module will pop-up. AGS101T User Manual... -
Page 19: Mini-Pcie & M.2 Cards Installation / Replacement
1. Thread and fasten the hex nut and the 2. Apply adhesive around here. washer. Then install the antenna. Info: The diameter of the nut is around 6.35 mm (0.25”-36UNC). AGS101T User Manual... -
Page 20: Mounting Installation
2.1.4.1. Wall-Mounting Installation 1. Turn your product upside down to attach the mounting brackets to your product and secure with the supplied 4 screws. 2. Prepare at least 4 screws (M3) to install the device on wall. AGS101T User Manual... -
Page 21: Hdd Module Installation
2. Hook the DIN rail mounting bracket over the top of the DIN rail, and then press the lower section of the bracket towards the DIN rail to clip the bracket onto it. 2.1.5 HDD Module Installation AGS101T User Manual... -
Page 22: Sim Card Installation
1. The SIM card socket design is push-in/push-out type. To install or remove a SIM card, remove the SIM card cover, as shown in the picture below, by releasing the M3 screw. After insertion/removal of the SIM card, replace the SIM card cover and lock it back into place. AGS101T User Manual... -
Page 23: Pinout For Com Ports, Dc-In Power & Line-Out Jack
RS-422 RS-485 DCD, Data carrier detect DATA- RXD, Receive data DATA+ TXD, Transmit data DTR, Data terminal ready RX- Ground Ground Ground DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator AGS101T User Manual... - Page 24 J2 DC-In Power Connector (3-pin terminal block) Assignment Power Ground Case Ground 9V ~ 36V Line-Out / Line-In Jack This connector supports Line-in and Line-out. Line-out supports a 2W speaker. Please see diagram below. AGS101T User Manual...
-
Page 25: Setting The Jumpers
1 2 3 When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. AGS101T User Manual... -
Page 26: Motherboard Jumper & Connector Locations
2.3 Motherboard Jumper & Connector Locations IB803T Motherboard AGS101T User Manual... -
Page 27: Ib803T Motherboard Jumpers And Connectors
2.4 IB803T Motherboard Jumpers and Connectors 2.4.1 SW1: Power Button Switch 2.4.2 RTC RST# (SW2-1) & SRTC RST# (SW2-2) RTC RST# (SW2-1) Function Setting Normal Clear CMOS SRTC RST# (SW2-2) Function Setting Normal Clear ME RTC Register AGS101T User Manual... -
Page 28: Dvi-I Connector (Cn1)
2.4.3 DVI-I Connector (CN1) 2.4.4 HDMI Connector (CN2) 2.4.5 2.5 Gigabit LAN RJ45 Connector (CN3) AGS101T User Manual... -
Page 29: Gigabit Lan Rj45 Connectors (Cn4)
Hardware Configuration 2.4.6 2.5 Gigabit LAN RJ45 Connectors (CN4) 2.4.7 Dual USB 3.1 Connector (CN5) 2.4.8 Dual USB 2.0 Connector (CN6) AGS101T User Manual... -
Page 30: Line-Out / Line-In Connector (Cn7)
2.4.9 Line-Out / Line-In Connector (CN7) 2.4.10 COM1 Connector (CN8) 2.4.11 SATA Connector (CN9) AGS101T User Manual... -
Page 31: Com2 Connector (Cn10)
Hardware Configuration 2.4.12 COM2 Connector (CN10) 2.4.13 AT/ATX Mode (JP1) Function Pin closed Illustration (default) AGS101T User Manual... -
Page 32: Reset Button Connector (J1)
2.4.14 Reset Button Connector (J1) Pin Assignment Ground Reset BTN 2.4.15 J2: DC-In Power Connector (3-pin terminal block) AGS101T User Manual... -
Page 33: J3: Rtc Battery Connector
Hardware Configuration 2.4.16 J3: RTC Battery Connector 2.4.17 J4: SPI Firmware Header 2.4.18 J5: DDR4 Socket AGS101T User Manual... -
Page 34: J6: Sata Power Connector
2.4.19 J6: SATA Power Connector Pin Assignment 2.4.20 J7: Mini PCIe Socket (Supports USB & SIM2) AGS101T User Manual... -
Page 35: J8: Mini Pcie Socket (Supports Usb & Sata)
Hardware Configuration 2.4.21 J8: Mini PCIe Socket (Supports USB & SATA) 2.4.22 J9(SIM1), J12(SIM2): SIM Socket 2.4.23 J10: Power IC JTAG AGS101T User Manual... -
Page 36: J11: Board-To-Board Connector
2.4.24 J11: Board-to-Board Connector AGS101T User Manual... - Page 37 (COM4) RXD, Receive data (COM4) RI, Ring indicator (COM4) TXD, Transmit data (COM4) DTR, Data terminal Ground ready USB_D+ Ground USB_D- PLT_RST# Ground Ground USB_D+ PCIE_CLK_DP USB_D- PCIE_CLK_DN Ground Ground VCC3_3 PCIE_RXP VCC3_3 PCIE_RXN Ground Ground 3VDUAL PCIE_TXP 3VDUAL PCIE_TXN AGS101T User Manual...
-
Page 38: J13: M.2 B-Key Socket (Supports Pcie & Usb3.0)
2.4.25 J13: M.2 B-Key Socket (Supports PCIe & USB3.0) 2.4.26 J14: Port 80 Header 2.4.27 LED1: Power_Fail (Red) 2.4.28 LED2: Heartbeat (Blue) 2.4.29 LED3: WWAN1 (Green) 2.4.30 LED4: WWAN2 (Green) AGS101T User Manual... -
Page 39: Chapter 3 Driver Installation
Chapter 3 Driver Installation The information provided in this chapter includes: • ® Intel Chipset Software Installation Utility • Graphics Driver Installation • HD Audio Driver Installation • ® Intel Management Engine Drivers Installation • LAN Driver Installation... -
Page 40: Introduction
Double click the file to decompress it. Run “CDGuide” to go to the main drivers page as shown. Click Intel on the left pane and then Intel(R) Elkhartlake Chipset Drivers on the right pane. AGS101T User Manual... - Page 41 Next to continue. 4. Accept the software license agreement and proceed with the installation process. 5. On the Readme File Information screen, click Install for installation. 6. After the installation, press Finish to complete the setup process. AGS101T User Manual...
-
Page 42: Graphics Driver Installation
3.3 Graphics Driver Installation 1. Click Intel on the left pane and then Intel(R) Elkhartlake Chipset Drivers on the right pane. 2. Click Intel(R) Elkhartlake Graphics Driver. 3. When the Welcome screen appears, click Next to continue. AGS101T User Manual... - Page 43 4. Click Yes to accept the license agreement and click Next in The Readme File Information screen. Click Next in the Setup Progress screen. 5. Restart the computer when prompted. Click Finish, then remove any installation media from the drives. AGS101T User Manual...
-
Page 44: Hd Audio Driver Installation
2. Click Realtek High Definition Audio Driver. 3. On the Welcome screen, click Next to continue. 4. When the InstallShield Wizard has successfully installed the Realtek Audio Driver, restart the computer. Click Finish to complete the setup. AGS101T User Manual... -
Page 45: Intel® Me Drivers Installation
Driver Installation 3.5 Intel® ME Drivers Installation 1. Click Intel on the left pane and then Intel(R) ME Drivers. 2. The welcome screen to the Intel® Management Engine Components appears. Click Next to continue. AGS101T User Manual... - Page 46 3. Accept the license agreement and click Next. 4. On the Setup’s Destination Folder screen, click Next to continue. 5. After the Intel® components have been completely installed, click Finish. AGS101T User Manual...
-
Page 47: Lan Driver Installation
2. Choose Intel(R) I21x Gigabit Network Drivers. 3. In the welcome screen to the install wizard for Intel(R) Network Connections, click Next. 4. On the next screen, accept the terms in the license agreement and click Next. AGS101T User Manual... - Page 48 5. In the Setup Options screen, click Next. 6. Click install to begin the installation. 7. Click Finish when Install wizard has completed. AGS101T User Manual...
-
Page 49: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •... -
Page 50: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. AGS101T User Manual... -
Page 51: Main Settings
BIOS Setup 4.3 Main Settings BIOS Setting Description Sets the date. System Date Use the <Tab> key to switch between the date elements. Set the time. System Time Use the <Tab> key to switch between the time elements. AGS101T User Manual... -
Page 52: Advanced Settings
Displays system ACPI parameters. Fintek Super IO Displays super IO chip parameters. Configuration Fintek Hardware Monitor Shows super IO monitor hardware status. USB Configuration Displays USB configuration parameters. Network Stack Enables / Disables UEFI Network Stack. Configuration AGS101T User Manual... - Page 53 BIOS Setup 4.4.1 CPU Configuration BIOS Setting Description When enabled, a VMM can ultilize the Intel (VMX) Virtualization additional hardware capabilities provided by Technolgy Varderpool Technology. AGS101T User Manual...
- Page 54 4.4.2 PCH-FW Configuration BIOS Setting Description When disabled, ME will be put into ME ME State temporarily Disabled Mode. AGS101T User Manual...
- Page 55 • TPM 2.0 will restrict support to TPM 2.0 devices only. • Device Select Auto will support both with the default being set to TPM 2.0 deices if not found, and TPM 1.2 device will be enumerated. AGS101T User Manual...
- Page 56 Enables / Disables the system ability to hibernate Hibernation (OS/S4 Sleep State). This option may be not effective with some OS. Selects an ACPI sleep state (Suspend Disabled or S3) ACPI Sleep where the system will enter when the Suspend button is State pressed. AGS101T User Manual...
- Page 57 BIOS Setting Description Power Failure Options: Always on, Always off Sets parameters of serial ports. Serial Ports Enables / Disables the serial port and select an optimal Configuration setting for the Super IO device. Serial Port 1 Configuration AGS101T User Manual...
- Page 58 Serial Port 2 Configuration AGS101T User Manual...
- Page 59 BIOS Setup Serial Port 3 Configuration AGS101T User Manual...
- Page 60 Serial Port 4 Configuration AGS101T User Manual...
- Page 61 Fintek Hardware Monitor BIOS Setting Description These fields are the parameters of the hardware monitoring function feature of the Temperatures / Voltages motherboard. The values are read-only as monitored by the system and showing the PC health status AGS101T User Manual...
- Page 62 For a Hub port, the delay is taken from Hub descriptor. Mas storage device emulation type. ‘AUTO’ Generic Ultra MS- enumerates devices according to their media format. Optical drives are emulated as ‘CDROM’ drives with COMBO no media will be emulated according to a drive type AGS101T User Manual...
- Page 63 BIOS Setup 4.4.8 Network Stack Configuration BIOS Setting Description Network Stack Enables / Disables UEFI Network Stack. AGS101T User Manual...
-
Page 64: Chipset Settings
Keep IGFX enabled based on the setup options GTT Size Options: 2MB, 4MB, 8MB Select the Aperture Size. Note: Above 4GB MMIO BIOS assignment is automatically enabled when Aperture Size selecting 2048MB aperture. To use this feature, please disable CSM Support AGS101T User Manual... - Page 65 Description SATA Controller(s) Enables / Disables the Serial ATA. SATA Mode Determines how SATA controller(s) operate. Selection Serial ATA Port 0~1 Enables / Disables Serial Port 0~1. SATA Ports Hot Enables / Disables SATA Ports HotPlug. Plug AGS101T User Manual...
- Page 66 BIOS Setting Description M.2 USB M.2 USB Configuration Settings Configuration Enable/Disable this USB Physical Connector M.2 USB 3.0 (physical port). Once disabled, any USB devices Support plugged into the connector will not be dtected by BIOS or OS. AGS101T User Manual...
-
Page 67: Security Settings
BIOS Setup 4.6 Security Settings BIOS Setting Description Setup Administrator Sets an administrator password for the setup Password utility. User Password Sets a user password. Secure Boot Secure Boot Configuration AGS101T User Manual... - Page 68 AGS101T User Manual...
- Page 69 BIOS Setup AGS101T User Manual...
- Page 70 AGS101T User Manual...
-
Page 71: Boot Settings
Turns on/off the keyboard NumLock state. Quiet Boot Enables / Disables Quiet Boot option. Fixed Boot Order Sets the system boot order. Priorities UEFI Hard Disk Drive Specifies the boot device priority sequence from BBS Priorities available UEFI hard disk drives. AGS101T User Manual... -
Page 72: Save & Exit Settings
Restores / Loads defaults values for all the Restore Defaults setup options. Save as User Defaults Saves the changes done so far as user defaults. Restores the user defaults to all the setup Restore User Defaults options. AGS101T User Manual... -
Page 73: Appendix
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. • I/O Port Address Map • Interrupt Request Lines (IRQ) • Watchdog Timer Configuration... -
Page 74: I/O Port Address Map
A. I/O Port Address Map AGS101T User Manual... - Page 75 Appendix AGS101T User Manual...
-
Page 76: Interrupt Request Lines (Irq)
IRQ 4294967280~85 Intel I226 Gigabit Network Connection #6 IRQ 4294967286~91 Intel I226 Gigabit Network Connection #4 IRQ 4294967292 Intel(R) UHD Graphics IRQ 4294967293 Intel(R) USB 3.10 eXtensible Host Controller - 1.20 (Microsoft) IRQ 4294967294 Standard SATA AHCI Controller AGS101T User Manual... -
Page 77: Watchdog Timer Configuration
**endptr; char SIO; printf("Fintek 81866 watch dog program\n"); SIO = Init_F81964(); if (SIO == 0) printf("Can not detect Fintek 81866, program abort.\n"); return(1); }//if (SIO == 0) if (argc != 2) printf(" Parameter incorrect!!\n"); return (1); AGS101T User Manual... - Page 78 //--------------------------------------------------------------------------- void DisableWDT(void) unsigned char bBuf; Set_F81964_LD(0x07); //switch to logic device 7 bBuf = Get_F81964_Reg(0xFA); bBuf &= ~0x01; Set_F81964_Reg(0xFA, bBuf); //disable WDTO output bBuf = Get_F81964_Reg(0xF5); bBuf &= ~0x20; bBuf |= 0x40; Set_F81964_Reg(0xF5, bBuf); //disable WDT //--------------------------------------------------------------------------- AGS101T User Manual...
- Page 79 (ucDid == 0x07) //Fintek 81866 goto Init_Finish; } F81964_BASE = 0x00; result = F81964_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_F81964 (void) outportb(F81964_INDEX_PORT, F81964_UNLOCK); outportb(F81964_INDEX_PORT, F81964_UNLOCK); //--------------------------------------------------------------------------- void Lock_F81964 (void) outportb(F81964_INDEX_PORT, F81964_LOCK); //--------------------------------------------------------------------------- void Set_F81964_LD( unsigned char LD) Unlock_F81964(); AGS101T User Manual...
- Page 80 #define F81964_DATA_PORT (F81964_BASE+1) //--------------------------------------------------------------------------- #define F81964_REG_LD 0x07 //--------------------------------------------------------------------------- #define F81964_UNLOCK 0x87 #define F81964_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_F81964(void); void Set_F81964_LD( unsigned char); void Set_F81964_Reg( unsigned char, unsigned char); unsigned char Get_F81964_Reg( unsigned char); //--------------------------------------------------------------------------- #endif // F81964_H AGS101T User Manual...
Need help?
Do you have a question about the AGS101T and is the answer not in the manual?
Questions and answers