Page 1
SERVICE MANUAL GN2SK CHASSIS ORIGINAL MANUAL ISSUE DATE: 2/2016 Segment: QH Version Date Subject 2/2016 Original manual issue. 3/2016 Addition of 75” Model (P.2, P.21~31, P.33~36, P63~68, P.71~74, P.135~175, P.185~190, P.194~195) Update entire manual LCD TV 9-888-586-02...
Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identified in this manual.
Page 4
Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance est critique pour la securite du fonctionnement sont identifi es dans le present manuel.
Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short. Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS). 10) It is recommended not to exceed 1 hour of Power-On nor Burn-in period with LCD panel face down condition, in repair activity. KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. 8. For safety reasons, repairing the Power board and/or Inverter board is prohibited. KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 7
Try both slots, if necessary, to locate the hot side on the line; the lamp should light at normal brilliance if the screw is at ground potential (see Figure B). KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
<B> Temp. sensor I2C No ACK [TEMP_ERR] <B/D> V By One lock error between Main device and 4KBE device [4KBE_ERR] <B>4KBE device UART communication error detection. <B/D> Software error [SW_ERR] italic: detect at startup sequence only. KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 9
To exit the Self Diagnostic screen... *If you want to finish service mode app, do AC OFF/ON →Service mode app is disable perfectly *if you want to move home menu, push <HOME>button →Service mode app do background(not disable perfectly) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
*When finished the operation of service mode , please AC Plug OFF/ON the TV set. If you don’t do AC plug OFF/ON, remain the Service Mode App and User can see the Service Mode after RC ON. (Refer the previous page.) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
2) Press “Enter” or “Return” button to return to Service Mode. Service Mode >> Model Information Self diagnosis History >> Video / Audio >> Panel / PQ >> General Setting >> Tuner >> Wifi >> [</>] Set [Home]Exit KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Select NO if input data is incorrect. >> Model Number Setting Serial Number Edit Press <Enter> to save answer. Service Mode >> Status Information >> Model Information >> Model Number Setting Serial Number Edit Input Data correct? KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 13
EEPROM. Service Mode The serial number that has been input is displayed. >> Status Information User can still edit the Serial Number. >> Model Information >> Model Number Setting Serial Number Edit Input Data correct? KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
4) Select one Product Name from the list, press <Enter> will pop dialog to inform user to confirm data. Model dependent settings will be overwritten into EEPROM. [MODEL_NUMBER_SETTING] _ _ _ _ _ _ _ _ _ _ _ _ KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 15
]> >> G WB Offset Panel / PQ <[ ]> General Setting >> B WB Offset Tuner >> Wifi / BT >> [</>] Set [Home]Exit b. To select “WB Adjustment”, press “→” button. [</>] Set [Home]Exit KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 16
*Please refer to another manual “Service Procedure for Panel, Board and Software Change / Upgrade(P/N:98881800x)” for details. B-board T-con Panel replace replace replace 1.T-con to 0.SoC to 0.SoC to Gamma T-con T-con 1.T-con to 0.SoC to 1.T-con Mura T-con to SoC 1.T-con to 0.SoC to 1.T-con T-con to SoC KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 17
General Setting HDD Performance Check HDD Performace Check Back << Aging mode <[On/Off]> Result <[ ]> >> HDD Performance Check << Back >> Update CI+ Credentials >> Boot count reset >> ECS Enable <[On/Off]> [</>] Set [Home]Exit KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 18
Boot count reset >> Wifi / BT >> ECS Enable <[On/Off]> [</>] Set [Home]Exit [</>] Set [Home]Exit 3) Result OK or NG will be displayed after HDD re-registration is succeed/failed. HDD Re-Register Result <[ ]> << Back KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Your software is up to date Some user settings may have changed during the update. Please remove the USB device and select [OK] to exit Please remove the USB device and select ”OK” to exit 5: finished 5: finished KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
(Dead Set) Inputs dots connect B* Board G* Board/ADP H* Board Speaker Wifi & BT Module LD* Board V By One FFC Tcon LCD Panel Panel Panel Soft- Power Power (Communication) (Backlight) TEMP ware Problem Audio 4KBE KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 21
B* Board B* Board Go to 1-2-1. NO POWER Go to 1-2-1. NO POWER U-COM FAILURE U-COM FAILURE Go to 1-3. NO POWER Go to 1-3. NO POWER DDCON/LDO DDCON/LDO Main Device Failure Main Device Failure KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 22
B* Board B* Board Go to 1-2-1. NO POWER Go to 1-2-1. NO POWER U-COM FAILURE U-COM FAILURE Go to 1-3. NO POWER Go to 1-3. NO POWER DDCON/LDO DDCON/LDO Main Device Failure Main Device Failure KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 23
If #pin19 goes High few seconds and downs to Low, Check 1.0V DDCON (IC9008) Is the voltage >3.0V? Is the voltage >3.0V? Check 12.5V Line (G board, LD or IC9007). Check P_ON_LNB Continue next page… IC9017 #pin15 Change IC9017 Is the voltage >3.0V? KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 24
If PANEL_PWER_ON (R9172) is 0V Check XRST Change IC9017 IC9017 #pin17 Is the voltage >3.0V? If BL_MUTE (R9090) is 0V Check BL_ON Change IC9017 IC9017 #pin18 Is the voltage >3.0V? ( IC9017 is working OK ) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 25
If #pin19 goes High few seconds and downs to Low, Is the voltage >3.0V? Is the voltage >3.0V? Check 12.5V Line (G board or IC403 on DPS). Check P_ON_LNB Continue next page… IC9017 #pin15 Change IC9017 Is the voltage >3.0V? KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 26
If PANEL_PWER_ON (R9172) is 0V Check XRST Change IC9017 IC9017 #pin17 Is the voltage >3.0V? If BL_MUTE (R9090) is 0V Check BL_ON Change IC9017 IC9017 #pin18 Is the voltage >3.0V? ( IC9017 is working OK ) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 27
Is voltage >12.0V? 1-2 No Power U-Com Failure Check Enable pin 1-2 No Power U-Com Failure Check Enable pin voltage voltage Is voltage >2.5V? Enable source Is voltage >2.5V? Enable source Change DDCON IC Change DDCON IC KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 28
G board or IC9003 Check Vcc voltage C9061 Check Is voltage >4V? Change D9001 D9001 Is diode ? Check +5V_MAIN DDCON (IC9001) Is IC9010 mounted? Check Enable Change IC9010 IC9010 #pin1 Is voltage >2.5V? Change DDCON IC9009 KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 29
G board or IC408 on DPS Check Vcc voltage Check Change D9001 C9061 D9001 Is voltage >4V? Is diode ? Check +5V_MAIN DDCON (IC9001) Check Enable IC9010 #pin1 Change IC9010 Is voltage >2.5V? Change DDCON IC9009 KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 30
Is voltage >3V? Is voltage >3V? Check Enable pin Check Enable pin 1-2 No Power U-Com Failure voltage voltage 1-2 No Power U-Com Failure Is voltage >3V? Is voltage >3V? Change LDO IC Change LDO IC KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 31
11/13 of on B Board (CN9000 BM1), Voltage > 13.2V ? Voltage > 13.2V ? BMFW2 Board / BMFW2 Board / R1004, R1005 IC9007 BM1 Board DPS Board / on BMFW2 Board on BMFW2 Board IC403 on DPS KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Under0.897V or less 3-3 Power Off Checking Audio check point Go to Audio Error B* Board Go to 3-4 Power On Checking LED driver or G* board/Adapter Change LD board or G* board/Adapter. Replace B Board Finish KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 33
Symptom on the B-Board improvement improvement B-Board is Panel (or T-Con) is suspicious suspicious Symptom improve Replace the Harness Harness is Between G-Board suspicious and B-Board Symptom improve Replace V-By-One FFC the V-By-One FFC is suspicious KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 34
DPS-Board Symptom Symptom improvement improvement Symptom improve Replace the Harness DPS is Panel (or T-Con) is Harness is Between G-Board suspicious suspicious suspicious and DPS Symptom improve Replace V-By-One FFC the V-By-One FFC is suspicious KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 35
Harness / Connection OK Voltage < 1.85 V Symptom Improvement LED driver or G board LD board/G board Change LD board or G board improvement Symptom Improvement Change Change Panel BMFW2 Board Panel BMFW2 Symptom Improvement improvement KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 36
Voltage < 1.85 V Change LD board or G board. Symptom improvement Improvement Change DPS Board Symptom Improvement Change Panel Panel Improvement Symptom Improvement Improvement Change 30P FFC 30P FFC between DPS and BM1 Improvement BM1 Board KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 37
OK? Change B* Board, improvement and Aging a few Panel hours Symptom improvement Check I2C_C bus Temp sensor B* Board NG communication OK? IC1400 (IC1400 #1,#6) I2C_C bus dumping or Muffin check KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 38
[Sound] Change [Sound] [Headphone Speaker Link] [Headphone Speaker Link] setting is [On] ? to [Off], OK ? Replace B Board Go to 3-3 Power Off Checking HP/Audio out terminal or Headphone detect GPIO may be broken KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 39
If impedance is <100Ω (3) Fuse open check (3) Fuse open check Measure impedance of fuse Measure impedance of fuse F7702 5A (12.5V or 19.5V) F7700, F7701 5A (12.5V or 19.5V) If fuse open If fuse open KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 40
Voltage rise more than 0V for a moment at power on DPS Board (4) POWER_AU check Measure voltage between PVDD and GND at capacitor Return to 2-2 Finish C7932, C7914. Voltage rise more than 0V for a moment at power on KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 41
MIN? is set to ? Replace B Board [Audio Out (Fixed)] Replace B Board [Audio Out (Variable)] Volume Increase Volume is set to MIN? Replace B Board [Subwoofer] Set [Headphone/Audio Out] to [Headphone] or [Audio Out] KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 42
TROUBLE SHOOTING FLOW 3-6. NO SOUND (TUNER) This troubleshooting is only for Analog No Sound with normal picture Only RF tuner input? Please refer Audio Check IC1000 (SOC) troubleshooting KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 43
Check Source equipment Change B-Board. Is Distributor used ? by Reference TV set And inform the designer of it (For example, RB2, RB1) Connect Source Check the settings of equipment directly Source equipment KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 44
BL_ON : L improvement improvement Check Other V by One FFC 5x Blinking Backlight Main board NG Portion: Harness 4-2. NO PICTURE (VIDEO) 4-3. NO PICTURE (COMPONENT) 4-4. NO PICTURE (@ TUNER) 4-5. NO PICTURE (HDMI) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 45
Problem Problem Problem Problem OK Condition : No solder splash can be seen OK Condition : No part short-circuited NG Condition : Solder splash can be seen NG Condition : Part short-circuited KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 46
Problem Problem Problem Problem OK Condition : No solder splash can be seen OK Condition : No part short-circuited NG Condition : Solder splash can be seen NG Condition : Part short-circuited KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 47
Check Tuner power line 12V LNB Voltage Terrestrial/Cable Analog 12V at JL6027 = 12V? Checking For TW & NA-ATSC All tuners except (MX/UC) only TW & NA-ATSC(MX/UC) Refer Analog Tuning Refer Digital Tuning 1 Refer Digital Tuning 2 KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 48
Check P_ON_LNB signal line MOSFET Q9019 Check fuse F6000 12V at JL9012 = 12V? at R9167 = 3.3V? broken Please refer DDCON Change the fuse troubleshooting Check harness between Please refer G-board troubleshooting B-Board and G-board Harness broken KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 49
- Parts for IFAGC line: R6072, R6009, R6010, R6069, C6302, R6303. Confirm ANT or Cable connection : Insert correct signal in correct terminal. Check part mounting condition for analog control line Change NG parts “IFOUT_N, IFOUT_P, IFAGC” Check IC1000(SOC) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 50
(IC reference -- destination) “TU1_TS_DATA0, TU1_TS_CLK, TU6001 - PA-T2 TU1_TS_VALID, TU1_TS_SYNC” TU6001 - LA-T2/LA-ISDB TU6001 - CH, HK TU6003 - AEP_W Check IC1000 (SoC) TU6802 - JP_SKP Change NG parts : Insert correct signal in correct terminal. KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 51
Check Source equipment Change B-Board. by Reference TV set And inform the designer of it (For example, RB1) Reference TV set Check the settings of Replace IC5212 (HDMI EQ). And inform the designer of it Source equipment KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 52
Check Source equipment Change B-Board. by Reference TV set And inform the designer of it (For example, RB1) Reference TV set Replace IC5212 (HDMI EQ) Check the settings of Source equipment And inform the designer of it KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 53
Check Source equipment Change B-Board. by Reference TV set And inform the designer of it (For example, RB1) Reference TV set Replace IC5212 (HDMI EQ). Check the settings of And inform the designer of it Source equipment KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 54
Check Source equipment Change B-Board. by Reference TV set And inform the designer of it (For example, RB1) Reference TV set Check the settings of Replace IC5212 (HDMI EQ). Source equipment And inform the designer of it KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 55
[BMFW2/BM1] In case that buttons error except power key R1042 : 4.7k [ohm] R1091 : 0 [ohm] Main device issue R1087 : 20k [ohm] Change B-board R1088 : 22k [ohm] * R1091 may be not mounted KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 56
Check resistor value on B- Parts issue R1502 : 47k [ohm] board * R1080 may be not mounted [BFM/BM2] R1110 : 0 [ohm] R1259 : 47k [ohm] Change B-board * R1110 may be not mounted Main device issue KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
• Hold wires KD-75XD8505, FW-75XD8501 ② ④ ③ ① VA Tape ⑨ ⑭ ⑮ ・Fix wire ⑫ Harness Tie x9 ⑪ ⑬ ⑩ • Fix wire ⑦ ⑧ ⑯ ⑤ ⑥ Slide Clamp x1 • Hold wires KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 74
PANEL HANDLING PANEL HANDLING PROHIBITED AREA Please do not touch area (T-CON & LD Area) and glass(Screen), when you hold a panel. KD-55XD8505/8577/8588/8599, KD-65XD8505/8577/8599, FW-65XD8501 KD-75XD8505, FW-75XD8501 FW-55XD8501 Glass(Screen)surface KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 75
]. Therefore please be careful in the case of the disassembly or assembly of parts. 1. KD-55XD8505/8577/8588/8599, FW-55XD8501 1-1. STAND 4 Screws (SCREW, +PSW M5 X12) P/N: 2-580-607-01 STAND REAR COVER 2 Screws (SCREW, PSW M6 X16) P/N: 2-580-611-01 STAND NECK STAND KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 77
On the other hand, when disassembling RC, you can ignore the handling prohibition area. 3 screws (SCREW +BVTP 3X10 TYPE2 IT-3) P/N: 7-685-647-79 Please refer to Appendix-1. 13 screws (SCREW M3X3.0 STEP) P/N: 4-579-926-01 REAR COVER (M1_L_PDT) A KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 78
DISASSEMBLY 1. KD-55XD8505/8577/8588/8599, FW-55XD8501 1-4. BRACKET, VESA (L_PDT) *Inner side view of Rear Cover Screw (SCREW +BVTP 3X8 TYPE2 IT-3) P/N: 7-685-646-79 BRACKET, VESA (L_PDT) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 79
DISASSEMBLY 1. KD-55XD8505/8577/8588/8599, FW-55XD8501 1-5. BRACKET, DC JACK (PDT) BRACKET, DC JACK (PDT) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 88
DISASSEMBLY 1. KD-55XD8505/8577/8588/8599, FW-55XD8501 1-14. SMART CORE (S) NOTE: For This For This Model Model SMART CORE (S) HARNESS ASSY (MAIN) 2 screws (SCREW, +PSW M3X6) P/N: 4-472-518-11 KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 89
DISASSEMBLY 1. KD-55XD8505/8577/8588/8599, FW-55XD8501 1-15. SWITCH UNIT (SM-G-WW) AND HARNESS ASSY (MAIN) HARNESS ASSY (MAIN) P/N: 1-910-110-91 HARNESS ASSY (MAIN) SWITCH UNIT (SM-G-WW) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 100
When you do panel replacement, please also replace this part at the same time to a new one. LABEL, SIDE TERMINAL (PDT M1) Caution: Don’t damage to LABEL. Scratch, deform, dirty etc..BRACKET, VESA (MIA) 2 screws (SCREW, +PSW M4X10) P/N: 4-159-298-01 KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 105
And when holding SP grille portion, you will touch a speaker cone. 13 screws (SCREW M3X3.0 STEP) P/N: 4-579-926-01 On the other hand, when disassembling RC, you can ignore the handling prohibition area. Please refer to Appendix-1. REAR COVER (M1_2L_PDT) A KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 113
DISASSEMBLY 2. KD-65XD8505/8577/8599, FW-65XD8501 2-12. SMART CORE (S) NOTE: For This For This Model Model SMART CORE (S) HARNESS ASSY (MAIN) 2 screws (SCREW, +PSW M3X6) P/N: 4-472-518-11 KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 114
DISASSEMBLY 2. KD-65XD8505/8577/8599, FW-65XD8501 2-13. SWITCH UNIT (SM-G-WW) AND HARNESS ASSY (MAIN) HARNESS ASSY (MAIN) P/N: 1-910-110-93 SWITCH UNIT (SM-G-WW) HARNESS ASSY (MAIN) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 117
DISASSEMBLY 2. KD-65XD8505/8577/8599, FW-65XD8501 2-16. PULLEY, STAND (HWI) PULLEY, STAND (HWI) P/N: 4-534-964-01 PULLEY, STAND (HWI) P/N: 4-534-964-01 KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 118
DISASSEMBLY 2. KD-65XD8505/8577/8599, FW-65XD8501 2-17. GL1 AND SPACER(17)+C 6 screws (SCREW, +PSW M3X6 W12) P/N: 4-256-393-12 Remove “Spacer(17)+C” at hole Number ”1”. KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 119
2-18. SHEET, INUSLATION (PDT 2L) AND CUSHION (PDT AC) NOTE: When you do panel replacement, SHEET, INUSLATION (PDT 2L) please also replace this part at the same time to a new one. 7±2 92±2 CUSHION (PDT AC) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 127
When you do panel replacement, please also replace this part at the same time to a new one. LABEL, SIDE TERMINAL (PDT M1) Caution: Don’t damage to LABEL. Scratch, deform, dirty etc..BRACKET, VESA(MIA) 4 screws (SCREW, +PSW M3X6) P/N: 4-472-518-11 KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
2-27. SCREW AND VA TAPE AND LCD PANEL When you do panel replacement, please also replace this part at the same time to a new one. VA TAPE 6 screws (SCREW M3X3.0 STEP) P/N: 4-579-926-01 LCD PANEL KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 130
DISASSEMBLY 3. SMART CORE (S) 3-2. WLAN / BT MODULE(11AC) AND BRACKET, WIFI NOTE: BRACKET, WIFI NOTE: For This Model WLAN / BT MODULE(11AC) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 131
When you do TOP COVER replacement, please also replace this part at the same time to a new one. SHEET, IR NOISE P/N: 4-590-730-01 60 x 13 (t0.2) Datum: edge of cover top Datum: edge of cover top hole COVER, TOP KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 165
4-31. LABEL, SIDE TERMINAL (PDT 3L) AND SHEET, THERMAL(BM) When you do panel replacement, please also replace this part at the same time to a new one. LABEL, SIDE TERMINAL (PDT 3L) Caution: Don’t damage to LABEL. Scratch, deform, dirty etc..SHEET, THERMAL(BM) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 184
EXPLODED VIEWS 3. SMART CORE (S) REF. No. PART No. DESCRIPTION MARK 4-580-149-01 PANEL, ORNAMENT A-2092-887-A HSC4-S MOUNT 4-580-146-01 CASE, BTM (S) 4-580-150-01 GUIDE, LIGHT 4-580-151-01 COVER, TOP 4-547-397-02 BRACKET, WIFI 1-458-853-11 WLAN/BT MODULE(11AC) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 185
SP-BOX ASSY(W20-SQ RCH CH-ND) 1-859-108-61 SP-BOX ASSY(D20-WF RCH CH-ND) 1-859-108-51 SP-BOX ASSY(D20-WF LCH CH-ND) 1-859-109-11 SP-BOX ASSY(W20-SQ LCH CH-ND) In the case of 75", install position of SP-BOX is opposite to parts name. SMART CORE (M) KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 192
APPENDIX-1 HOW TO TAKE OFF A REAR COVER Push the Rear Cover to up direction after pull up the reflector structure on Rear Cover slightly. You can disassemble Rear Cover by sliding. KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 193
Please refer SBR "New Potting TIM Operation for board repair" for details. HOLDER, HS WS (MUF) 4-548-743-01 Push Push HEAT SINK (MUFF) HEAT SINK (MUFF CP) Unhook HOLDER,(HS MUF) HOLDER, (HS MUF) 4-549-188-01 Do not reuse HOLDER. Should be replaced to new parts. KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 194
4-549-395-01 BM1 board. Fin Qty: 9 HOLDER, HS WS (MUF) Fin Qty: 13 4-548-743-01 Push Unhook HOLDER,(HS MUF) Do not reuse HOLDER. Should be replaced to new parts. 75”: HEAT SINK (MUFF2_C) HOLDER, (HS MUF) 4-549-188-01 KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Page 195
Please refer SBR "New Potting TIM Operation for board repair" for details. HOLDER, HS WS (MUF) 4-548-743-01 Push Unhook HOLDER,(HS MUF) Do not reuse HOLDER. Should be replaced to new parts. HEAT SINK (MUFF) HOLDER, (HS MUF) 4-549-188-01 KD-55XD8505/8577/8588/8599, 65XD8505/8577/8599, 75XD8505, FW-55/65/75XD8501...
Need help?
Do you have a question about the KD-55XD8505 and is the answer not in the manual?
Questions and answers