Subscribe to Our Youtube Channel
Related Manuals for MAXPEEDINGRODS MXR2300
Summary of Contents for MAXPEEDINGRODS MXR2300
- Page 1 USER MANUAL FOR MODELS: MXR2300 Digital lnverter Generator 1800 Running Watts 2300 Peak Watts...
- Page 2 ENGLISH 2-24 DEUTSCH 26-49 FRANÇAIS 51-74...
-
Page 3: Technical Specifications
Running Peak (RPM) Type piug Disp(cc) Bore Oil Type Number Number Watts Watts MXR2300 1800 2300 5000 A5RTC 79.7 64X45 0.35 10W30 NEUTRAL FLOATING For portable generators where the neutral is floating, the operator's manual shall include the following wording or equivalent:... -
Page 4: Limited Warranty
2. WHO GIVES THIS WARRANTY (WARRANTOR): Chongqing Guoyu Technology Co., Ltd 3. WHO RECEIVES THIS WARRANTY(PURCHASER): The original purchaser (other than for purposes of resale) of the MAXPEEDINGRODS inverter. 4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any portable generator supplied or manufactured by Warrantor. -
Page 5: Table Of Contents
Safety Labels and Decals Cleaning the Air Filter Draining the Float Bowl UNPACKING Spark Plug Maintenance FEATURES Cleaning the Spark Arrestor Basic Inverter Features MXR2300 Cleaning the Inverter 8Control Panel Features MXR2300 Storage OPERATION TROUBLESHOOTING Before Starting the Inverter SCHEMATIC... -
Page 6: Safety
Read Manufacturer's Instructions NOTE: Indicates a procedure, practice or condition that should be followed in order for the generator Read Safety Messages Before to function in the manner intended. Proceeding Wear Personail Protective Equipment (PPE) MAXPEEDINGRODS... -
Page 7: General Safety Rules
Never use the inverter to power medical support equipment. engine misfires often. Always disconnect tools or Always remove any tools or other service equipment used appliances from the inverter during maintenance from the inverter before operating. before starting. 6 MAXPEEDINGRODS... -
Page 8: Safety Labels And Decals
SAFETY SAFETY LABELS AND DECALS MXR2300 Do not use the generator in a direction that the A hot exhaust system can cause serious bums, exhaust emission to the occupied structures, the avoid contact if the engine has been running. sparks in the exhaust emission may start fires. -
Page 9: Features
FEATURES BASIC INVERTER FEATURES MXR2300 Fuel Cap and Vent: Open the vent to run Engine Service Panel: Remove the panel to the engine and close the vent when the access the engine for maintenance. engine is off. Muffler and Spark Arrestor: Avoid contact until Control Panel: Contains the reset breaker, the engine is cooled down. -
Page 10: 8Control Panel Features Mxr2300
CHOKE AC RESET 2.1A PARALLEL CONNECTORS CONTROL PANEL FEATURES MXR2300 USB duplex: 5V DC with 1 amp and 2.1 amp. Parallel Connectors: To increase AC power 230 volts, 16-amp EU Outlet: The outlet is output, the connector sockets are used to capable of carrying a maximum of 16 amps. -
Page 11: Operation
Only operate the inverter on a solid, level surface. Operating the inverter on a surface with loose material such as sand or grass clippings can cause debris to be ingested by the inverter that could: • Block cooling vents • Block air intake system 10 MAXPEEDINGRODS... -
Page 12: Powercord
POWERCORD Using Extension Cords MAXPEEDINGRODS Portable Power assumes no responsibility for the content within this table. The use of this table is the responsibility of the user only. This table is intended for reference only. The results produced by using this table are not guaranteed to be correct or applicable in all situations as the type and construction of cords are highly variable. -
Page 13: Initial Oil Fill
See correct oil level in Figure 4. Figure 1: Engine Service Panel Figure 4: Engine Oil Correct Level 2. Clean the area around the oil fill/drain plug and remove plug (See Figure 2). Figure 2: Oil Fill/Drain Plug 12 MAXPEEDINGRODS... -
Page 14: Adding/Checking Engine Fluids And Fuel
The engine is equipped with a low oil shutdown switch. If the oil level becomes low, the engine may shut down and not start until the oil is filled to the proper level. Figure 5: Maximum Gasoline Fill Level MAXPEEDINGRODS... -
Page 15: Starting Mxr2300
Figure 8: Turn Engine/Fuel Switch to RUN Starting MXR2300 1. Check oil levels. If it is the first time starting make sure to add oil (see Initial Oil Fill on page 12). 2. Turn the fuel tank vent to the ON position... -
Page 16: Stopping The Inverter
3. As a load is applied, the inverter will sense the load and engine RPM will increase according to the load applied. 4. To run the inverter at maximum power and RPM, press the efficiency mode switch to the OFF position. MAXPEEDINGRODS... -
Page 17: Maintenance
6 Months 6 Months or Every Year Engine Oil Check Level Change Change Cooling Features Check/Clean Air Filter Check Clean* Replace Spark Plug Replace Check/Clean Spark Arrestor Check/Clean *Service more frequently if operating in dry and dusty conditions. 16 MAXPEEDINGRODS... -
Page 18: Engine Oil Maintenance
・The oil level is acceptable if oil is visible at the bottom of the threads of the oil fill plug. ・If oil level is low, add to the correct level using the supplied oil fill bottle. Do not overfill the oil crankcase. MAXPEEDINGRODS... -
Page 19: Changing Engine Oil
3. Unscrew the air cleaner cover and tip the cover down (see Figure 14) 4. Remove the foam element from the air cleaner housing. Figure 13: Carefully tip Inverter so oil flows into oil pan Figure 14: Unscrew air cleaner cover 18 MAXPEEDINGRODS... -
Page 20: Draining The Float Bowl
2. Locate the clear plastic hose from the float that hazardous materials. Consult local authorities or reclamation facility. is exiting out the bottom of the inverter, and place a suitable container under it to catch the 5. Install the engine service panel. drained fuel (see Figure 16). MAXPEEDINGRODS... -
Page 21: Spark Plug Maintenance
5. Clean area around the spark plug. 6. Using the spark plug socket wrench provided, remove the spark plug from the cylinder head (see Figure 19). Figure 18: Slide off spark plug cover 20 MAXPEEDINGRODS... -
Page 22: Cleaning The Spark Arrestor
7. Replace the spark plug (see Spark Plug screwdriver Maintenance on page 20). 10. Replace the discharge gate. 8. Move the inverter to a clean, dry place for storage. MAXPEEDINGRODS... -
Page 23: Troubleshooting
2. Clean the air filter (see page 18). Engine runs erratic; does not 3. Applied loads maybe cycling on and 3. As applied loads cycle, changes in hold a steady RPM. engine speed may occur; this is a normal condition. 22 MAXPEEDINGRODS... -
Page 24: Schematic
MXR2300 SCHEMATICS MAXPEEDINGRODS... - Page 25 Product: Inverter generator Type/Model: MXR2300, MXR3500, MXR5500 The statement is based on a single evaluation of above-mentioned products. All products in series production are in conformity with the product sample detailed in this report. We Chongqing Guoyu Technology Co., Ltd hereby declare that this product(s) described complies with the relevant basic...
Need help?
Do you have a question about the MXR2300 and is the answer not in the manual?
Questions and answers