Related Manuals for Delta Tau Accessory E1
Summary of Contents for Delta Tau Accessory E1
- Page 1 sales@artisantg.com artisantg.com (217) 352-9330 | Visit our website - Click HERE...
- Page 2 HARDWARE REFERENCE MANUAL ^2Accessory E1 UMAC POWER SUPPLY 3-3269A-00- 000- 000 January 31, 2022 Document # MN-000212...
- Page 3 © 2022 Delta Tau Data Systems, Inc. All rights reserved. This document is furnished for the customers of Delta Tau Data Systems, Inc. Other uses are unauthorized without written permission of Delta Tau Data Systems, Inc. Information contained in this manual may be updated from time-to-time due to product improvements, etc., and may not conform in every respect to...
- Page 4 Accessory E1 Safety Instructions Qualified personnel must transport, assemble, install, and maintain this equipment. Properly qualified personnel are persons who are familiar with the transport, assembly, installation, and operation of equipment. The qualified personnel must know and observe the following standards and regulations: IEC364resp.CENELEC HD 384 or DIN VDE 0100...
- Page 5 Accessory E1 REVISION HISTORY REV. DESCRIPTION DATE CHG APPVD Added CE Declaration 06/08/06 Marked For Full Release 07/07/06 Added UL Seal To Manual Cover 10/01/09 Updated Agency of Approval section Added KC Conformity 10/17/18 Corrected Specifications P.9 - 11 05/02/19 Added New Model Information P.4 - 7...
-
Page 7: Table Of Contents
Accessory E1 Table of Contents INTRODUCTION......................... 8 PRODUCT OPTIONS ......................8 PRODUCT Part Number ....................... 9 SAFETY INSTRUCTIONS ....................... 10 Power Disconnect ....................... 11 SPECIFICATIONS........................12 Environmental Specifications ....................12 Physical Specifications ......................12 Power Supply Input Specifications ..................12 Power Supply Output Specifications .................. - Page 8 Accessory E1 (This page is intentionally left blank) Table of Contents...
-
Page 9: Introduction
Accessory E1 INTRODUCTION The ACC-E1 power supply module is an accessory card that provides the UMAC backplane with power. This ACC-E1 has an AC input connector to the switching power supply and provides DC outputs to the UMAC control system via the UBUS backplane. The ACC-E1 also has a terminal block connector that provides the regulated +5Vdc and ±15Vdc that can be used for general purpose DC power to other... -
Page 10: Product Part Number
Accessory E1 PRODUCT Part Number Part Number Description Note ACC-E1 power supply with: - black face plate 3-3269A-00-C000-B000 - black top plate Individually - black bottom plate with cooling fan packaged item - four screws of top/bottom plates - two card guides... -
Page 11: Safety Instructions
Accessory E1 SAFETY INSTRUCTIONS Qualified personnel must transport, assemble, install, and maintain this equipment. Properly qualified personnel are persons who are familiar with the transport, assembly, installation, and operation of equipment. The qualified personnel must know and observe the following standards and regulations: IEC 364 resp. -
Page 12: Power Disconnect
Accessory E1 Power Disconnect A power disconnect should be installed by the user between the input power service and the ACC-E1 power supply for a fail–safe method to disconnect power. Safety instructions... -
Page 13: Specifications
Accessory E1 SPECIFICATIONS Please note that these are design specifications. Performance may differ slightly from these design specifications. These specifications are with cooling fan. Installing Cooling fan is highly recommend for ACC-E1. It affects reducing efficiency and operating temperature. Environmental Specifications... -
Page 14: Power Supply Output Specifications
-15V @ 1.5A Overload Protection 120.75W min Short Circuit Protection Short term (+5V only) The power supply has a ceramic tube fuse with lead wire rated at 250V @ 5A. If this fuse fails, please send unit back to Delta Tau. Specifications... -
Page 15: Agency Approval And Safety
Accessory E1 Agency Approval and Safety Item Description CE Mark EN61326-1 EN55011 Class A Group 1 EN61000-3-2 Class A EN61000-3-3 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-11 UL 61010-1 File E316989 CAN/CSA C22.2 No. 1010.1-92 File E316989 Flammability Class UL 94V-0... -
Page 16: Mechanical Specifications
Accessory E1 Mechanical Specifications ACC-E1 Layout 16 AWG WIRE FACEPLATE 3 SLOT ACC-E1 Top View Specifications... -
Page 17: Voltage Adjustment
Accessory E1 Voltage Adjustment Factory sets VR101 to adjust +5V. Specifications... -
Page 18: Ac Input Connector
Accessory E1 AC Input Connector The AC input plug on the power supply unit is an IEC male type meant to meet the globally accepted IEC publication 320, Class 1 industry standard AC input. Item Specification Connector Rated Voltage 250 VAC... -
Page 19: Mounting And Installation
Accessory E1 MOUNTING AND INSTALLATION To connect a UMAC accessory, simply slide the board into any open slot of the UMAC rack. Customarily, accessories are installed from left to right as follows: 10, 15, or 21-slot rack Prior to installation, make sure that you have set the jumpers and address settings to your desired requirements. -
Page 20: Acc-E1 Pinouts
Accessory E1 ACC-E1 PINOUTS TB1 / TB101 – Power Supply Output Tap This is a 6 pin Phoenix Combicon connector. This is a supply output connector which has 10A rated Contacts and has a UL 94V0 flammability rating. PIN# Name... -
Page 21: D1,D2,D3 / D102,D103,D104 - Power Indicators
Accessory E1 D1,D2,D3 / D102,D103,D104 – Power Indicators The ACC-E1 has three red LED indicators to inform the user that the 5V, +15V, and –15V supplies are operational. Description +5V power indicator +15V power indicator -15V power indicator ACC-E1 PINOUTS... -
Page 22: Specifications For Rev106 And Below
+16.3V @ 1.5A with fan -16.3V @ 1.5A with fan Overload Protection 195W, +35W The power supply has an in line slow-blow fuse rated at 250V @ 3.5A. If this fuse fails, please send unit back to Delta Tau. Specifications for Rev106 and below... -
Page 23: Agency Approval And Safety For Rev106 And Below
Accessory E1 Agency Approval and Safety for Rev106 and below Item Description CE Mark EN61326-1 EN55011 Class A Group 1 EN61000-3-2 Class A EN61000-3-3 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-11 UL 61010-1 File E314517 CAN/CSA C22.2 No. 1010.1-92 File E314517... -
Page 24: Mechanical Specifications For Rev106 And Below
Accessory E1 Mechanical Specifications for Rev106 and below ACC-E1 Layout 16 AWG WIRE FACEPLATE 3 SLOT ACC-E1 Top View Pin 1 Specifications for Rev106 and below...
Need help?
Do you have a question about the Accessory E1 and is the answer not in the manual?
Questions and answers