1. Manuals
  2. Brands
  3. optonica Manuals
  4. Lighting Equipment
  5. 260W Touch Screen Beam Moving Head
  6. User manual

optonica 260W Touch Screen Beam Moving Head User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
260W Touch Screen Beam Moving Head

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 260W Touch Screen Beam Moving Head and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for optonica 260W Touch Screen Beam Moving Head

Summary of Contents for optonica 260W Touch Screen Beam Moving Head

  • Page 1 260W Touch Screen Beam Moving Head...
  • Page 2 USER MANUAL...

  • Page 3: Table Of Contents

    Table of Contents 1. Attention and installation ......................1 1.1 Instruction ........................1 1.2 Maintenance ........................1 1.3 Attention ........................... 1 1.4 Product presentation ......................1 1.5 DMX connection ......................2 1.6 Fixtures installation ......................3 2. CONTROL PANEL ......................... 4 2.1 Button description ......................

  • Page 4: Attention And Installation

    Attention and installation Instruction Thank you for using our company's products.When the product leaves the factory, the performance is good condition and the packing is complete. For your own safety,please read this user manual carefully before installing the device.This manual covers the important information of installing and using, please install and operate following the manual book .meanwhile,please keep this manual for using an anytime.

  • Page 5: Dmx Connection

     540° of pan movement,270° of tilt movement.  Intelligent thermal protection protection;  Control mode: DMX512/ master-slave/Auto-run;  IP20 protection grades. 1.5 DMX connection The fixture is equipped with both 3-pin or 5-pin XLR sockets for DMX input and output.Please use the twisted pair signal line specially shielded for DMX 512.The signal line is generally connected at a distance of 150m.
  • Page 6 the installation place, In upside down installation must be Keep the lamp don't drop the support frame,Prevent lamps from falling and sliding,need to use safety rope through support frame and lamp handle . Pedestrians are forbidden to pass under the lamp during installation and commissioning,check safety rope regularly for wear and tear, hook screws are No loosening.

  • Page 7: Control Panel

    CONTROL PANEL 2.1 Button description Picture 3 Diagram of the panel keys 第 4 页...

  • Page 8: Menu Description

    2.2 Menu description Picture 4 Main menu diagrammatic sketch 2.2.1 Setting Options Description Run Mode Status of Slave: receive the DMX signal from the main console or master AUTO 1 Demonstration of AUTO run effect. Status of Master：AUTO and send DMX signal to slave AUTO 2 Random Sound...

  • Page 9: Manually

    Invert channels of Pan-Tilt(including fine-tuning) Pan-Tilt Use encoder (optocoupler)to estimate the wrong step and Encoder right the wrong position Don’t use encoder(optocoupler) to right the position DMX Signal KEEP Keep going as this status CLEAR Motor return, stop running. Display Always bright screen saver Lamp on after...

  • Page 10: System

    22CH. gobo speed 0~255 Show when the Channel Mode is set to “Extended CH22” 2.2.3 System Options Descriptions DIS Ver Display version MT Ver Motor version DMX Channel value Go into sub-interface, show the channel value using number and percent System Errors Log If red ERR is on, it means lamp runs error, go into sub-interface to check the detail.You can press “Clear”...

  • Page 11: Advanced

    2.2.4 Advanced Set a layer of password here, in case that non-professionals’ misuse. Default password is “UP DOWN UP DOWN”, then “OK”. Options Descriptions Sensor Pan Hall status 0 is detected, otherwise 1 Monitoring Tilt Hall status 0 is detected, otherwise 1 Color Wheel Hall status 0 is detected, otherwise 1 Gobo Hall Status...

  • Page 12: Channel Function

    CHANNEL FUNCTION 3.1 Channel list CHANNE CHANNEL MODE COLOUR WHEEL COLOUR WHEEL STROBE STROBE DIMMER DIMMER STATIC GOBO CHANGE STATIC GOBO CHANGE PRISM 1 INSERTION PRISM 1 INSERTION PRISM 1 ROTATION PRISM 1 ROTATION PRISM 2 INSERTION PRISM 2 INSERTION PRISM 2 ROTATION PRISM 2 ROTATION FOCUS...
  • Page 13 050 - 054 Color 5 055 - 059 Color 5+Color 6 060 - 064 Color 6 065 - 069 Color 6+Color 7 070 - 074 Color 7 075 - 079 Color 7+Color 8 080 - 084 Color 8 085 - 089 Color 8+Color 9 090 - 094 Color 9...
  • Page 14 075 - 079 Gobo 2 shakes （from slow to fast） 080 - 084 Gobo 3 shakes （from slow to fast） 085 - 089 Gobo 4 shakes （from slow to fast） 090 - 094 Gobo 5 shakes （from slow to fast） 095 - 099 Gobo 6 shakes （from slow to fast）...

  • Page 15: Troubleshooting

    200-205 Lamp on EXTENDED CHANNEL EMPTY COLOUR TIME DIMMER-PRISM-FR 000-255 OST TIME Speed from fast to slow GOBO TIME TROUBLESHOOTING It is recommended some solution for some normal trouble shooting. Any inextricable problems should always be handling by the professional person. Disconnect the power supply before maintenance the light.
  • Page 16 Please check the electric parts(such as the transformer,PCB board,controller) is  short-circuit or burn down. on working,the pan&tilt couldn't work normally Please check according to the above step by step.  Please check the belt of the X/Y is broken. ...

Table of Contents