Download
Share
Print this page
  1. Manuals
  2. Brands
  3. NAC Image Technology Manuals
  4. Machine Vision Systems
  5. ST-822
  6. Supplemental user's manual

NAC Image Technology ST-822 Supplemental User's Manual

Memrecam q1m/q1v hxlink install
Hide thumbs Also See for ST-822:

Advertisement

Quick Links

Download this manual
MEMRECAM Q1m/Q1v
HXLink install
Supplemental User's
Manual
Model ST-822
This book is a manual about an installation procedure of HXLink before using
Q1m/Q1v.
APRIL 2015
25
(00396)B

Advertisement

loading
Need help?

Need help?

Do you have a question about the ST-822 and is the answer not in the manual?

Questions and answers

Related Manuals for NAC Image Technology ST-822

Summary of Contents for NAC Image Technology ST-822

  • Page 1 MEMRECAM Q1m/Q1v HXLink install Supplemental User’s Manual Model ST-822 This book is a manual about an installation procedure of HXLink before using Q1m/Q1v. APRIL 2015 (00396)B...
  • Page 2 PC Settings PC Settings Have the user with Windows Administrators authorization log in. Connect the powered up HUB or camera to the LAN port used for camera control. This manual describes the setting method for Windows7. ■PC IP Address Settings １...
  • Page 3 PC Settings Click "Properties" in the "Local Area Connection Status" window to open the "Properties" window for the local area connection. Select "Internet Protocol Version (TCP/IPv4)" in the items under the "This Connection Uses the Following Items" in "Local Area Connection Properties", and then click on "Properties"...
  • Page 4 PC Settings ７ As shown in the figure on the right, set the PC IP address to 172.21.80.1 and set the subnet mask to 255.255.0.0.  Click OK for "Internet Protocol (TCP/IP) Properties", and then click OK for the "Local Area Connection Properties"...
  • Page 5 PC Settings ■How to check the set IP address Confirm the IP address set for the PC by performing the ipconfig command with the command prompt. １ Open accessories from the Windows start button and click "Command Prompts" to open. Type in ipconfig and press Enter to display the PC IP address.
  • Page 6 PC Settings ■Disable sound device function Disable sound function at Windows in order to stabilize Q1m/Q1v communication. This manual describes the setting method for Windows7. １ Open the control panel from the Windows start button. Click to open “Hardware and Sound”. ３...
  • Page 7 PC Settings Click “Yes” when confirmation message appears. If a message to reboot PC appeared, reboot PC accordingly. This is all the process to disable sound function.  It is not necessary to disable sound function for MEMRECAM camera except Q1m/ Q1v (00396)B...
  • Page 8 PC Settings ■How to check the status of Sound function. １ Open the control panel from the Windows start button. Click to open “Hardware and Sound”. ３ Click to open “Manage audio devices”. Confirm “No audio devices are installed” is displayed.
  • Page 9 PC Settings If sound function is still effective, the devices (example: High Definition Audio Device) is displayed. (00396)B...

  • Page 10: Installation Procedures

    Installation Procedures Installation Procedures The following settings can be required prior to installation. Start the HXLink installation once the settings are complete. For using Q camera,Install GenICam and GigE Vision Filter Driver in accordance with the environment.  Confirm your windows environment prior to HXLink installation. Open “Control Panel”, “all control panel items”, “System”, check whether 32bit/ 64bit in ”System type”.
  • Page 11 Installation Procedures ■Installation start Have an authorized user of the Windows Administrators group log on.  Please finish all the application of the PC.  １ Once all of the PC applications have been completed, the "Automatic Playback" window is displayed when the HXLink CD is inserted into the PC CD drive.
  • Page 12 Installation Procedures ■Install Microsoft Visual C++ 2010 In VS2010 folder, there is a 32bit program installer for vcredist_x86.exe and 64bit program installer vcredist_x64.exe Please run vcredist_x86.exe only if you want to install the HXLink 32bit version, both of vcredist_x86.exe and vcredist_x64.exe If you are installing the HXLink 64bit version. Lists the steps to install the HXLink 64bit version.
  • Page 13 Installation Procedures ■Install GigE Vision Filter Driver ・ Installation is necessary in GigE Vision Filter Driver to use Q1m/Q1v.. １ Open the control panel from the Windows start button. Click to open "View network status and tasks". ２ Click to open "Change Adapter Settings". ３...
  • Page 14 Installation Procedures ４ Click "Properties" in the "Local Area Connection Status" window to open the "Properties" window for the local area connection. ５ Click “Install” in “Networking” tab. ６ Click “Service” as the type of network feature, and click “Add”. (00396)B...
  • Page 15 Installation Procedures ７ Click “Have Disk” to set installation disk. ８ Click “Browse” to insert the manufacture’s installation disk. ９ Open explorer and confirm the following folder in install CD according to your OS.  Windows OS 32bit :GigE_FilterDriver(x86) Windows OS 64bit:GigE_FilterDriver(x64) ...
  • Page 16 Installation Procedures Click “OK” Select “GigE Vision Filter Driver” as the Network service you want to install and click “OK”. If “Windows Security” window is displayed, click “Install”. Installation completed in a few seconds. Finally, open “Properties” window for the local area connection again and make sure that “GigE Vision Filter Driver”...
  • Page 17 Installation Procedures ■Install HXLink Application １ Displays the launcher by double-clicking the Launcher.exe of HXLink installer. Click the button of HXLink 32bit version / 64bit version to install. ２ Click "Yes", and then continue with the installation. ３ Upon starting the installation, "Welcome to the MEMRECAM HXLink Setup"...
  • Page 18 Installation Procedures ４ When environment for using Q camera is not prepared, the following either warning can be displayed. If you do not use Q camera, click “No” and  continue HXLink installation ５ Case1: In 32bit OS, Click “Yes” to install GenICam 32bit. Follow the wizard instructions to finish GenICam installation and continue HXLink installation.
  • Page 19 Installation Procedures ８ Set the fx camera connection method. If not using an fx camera, or if using a TCP/IP connection, simply click "Next".  If using an fx camera with an FC-AL connection, select "Use fx Camera with an FC-AL Connection"...
  • Page 20 Installation Procedures If changing the drive or folder for installing the program, click "Browse" and set the folder for installing the program. After designating the folder, click "Next". Select the previously set folder If changing the default settings, click "Browse" ...
  • Page 21 Installation Procedures This performs "TCP IP Network Optimization"  If using an Q1m/Q1v, HX, GX or an fx camera connection, check the network and click OK.  If using only the fx camera FC-AL, click Cancel. Click "Finish" when the dialog for setup complete is displayed.

  • Page 22: Uninstallation Procedures

    Uninstallation Procedures Uninstallation Procedures Uninstall the MEMRECAM HXLink if not needed. Saved data is not deleted even if HXLink is uninstalled. An authorized user of the Windows Administrators group should log on. ■Uninstall HXLink Application １ Click "Programs" and "Uninstall Programs" from the "Control Panel".
  • Page 23 Uninstallation Procedures HXLink cannot be uninstalled if running. The dialog shown to the left will appear if HXLink is running, so follow the instructions to proceed. Once the uninstall is complete, the uninstalled program is removed from the "MEMRECAM HXLink" list. (00396)B...
  • Page 24 Uninstallation Procedures ■Uninstall GigE Vision Filter Driver １ Open “Properties” window for the local area connection. Select “GigE Vision Filter Driver” and click “Uninstall”. ２ Click “Yes”. Then, uninstallation completed. ■Uninstall GenICam １ Open “Control Panel” and click “Uninstall Programs”. Select “GenICam v2.2”...