Subscribe to Our Youtube Channel
Related Manuals for easybike PROMENADE
Summary of Contents for easybike PROMENADE
- Page 1 EASYBIKE PROMENADE USER MANUAL AND WARRANTY CARD EASYBIKE PROMENADE STUDY CAREFULLY BEFORE DRIVING!
- Page 2 1.YOUR NEW ELECTRIC BIKE 1.1. Home General introduction to electric bikes 2.WHEEL MAINTENANCE Seat adjustment Safety instructions before driving Suspension fork Driving in bad weather 3. ELECTROSADA Batteries Removing and installing the battery 3.1.1 Charging 3.1.2 Normal battery behaviour 3.1.3 Storage 3.1.4 Driving distance factors...
- Page 3 Road Traffic Act. This means that you can ride on cycle paths, you symbol according to the valid and required standards. If any changes are made to the EasyBike without the prior consent of LKQ CZ don't need a driving licence and a helmet is only compulsory up to s.r.o., this declaration will become invalid.
- Page 4 2.Service bikes 2.1. SEATING SETUP Saddle height adjustment Release the quick- release lever and adjust the seat height to the desired level. However, do not exceed the maximum extension level marked on the seat tube. Doing so could either damage the seat or to break out of the frame.
- Page 5 Observe the rules of safe driving on roads laid down by generally binding legal regulations. Remember that a cyclist is a full-fledged road user who is subject to the same rules as the driver of a motor vehicle. The bicycle is equipped with reflective elements for daytime riding. For riding at night or in low visibility, lighting must be used as defined by the current law.
- Page 6 2.4. DRIVING IN BAD WEATHER In light rain, the ride doesn't matter. However, it is not advisable to leave or park your bike where it is not protected against rain, snow and sun. 3. Elektrosada 3.1. BATTERIES 15 Ah / 540 Wh, Li-Ion technology, Samsung cells. 3.1.1.
-
Page 7: Important Notices
IMPORTANT NOTICES! •Charge the battery in a dry environment to prevent damage from short circuits. •Never leave the battery unattended for long periods of time when charging it. •Charge the battery ideally once every 2 months, even when the bike is not in use, to at least 60% capacity. •Do not cover the battery or charger. - Page 8 3.1.5. DISTANCE FACTORS Tyre rolling resistance It is important to inflate your tyres correctly, so if you have under-inflated tyres on your e-bike, for example, your range will be reduced (and you risk a puncture). Weight of rider and load The lower the weight, the longer the range of the electric bike.
- Page 9 3.2.Technical information about the VINKA DR23 display DR23 1.Episode no.: SIDE LCD DISPLAY 2.Type: 3.Environmental regulation: the RoHS 4.Basic features: ITEMS FEATURES Rated voltage 36,0 V Operating temperature -20 to +60 °C Storage temperature -30 to +70 °C LCD operating temperature -20 to approximately +70 °C Storage temperature LCD -13 to approximately +80 °C...
- Page 10 3.2.1. DR23 display Functional layout of the DR23 display DR23 is a side LCD display. It offers Light indicatorBike pushing aidFunction list a standard set of indicators and functions that are important for driving on the elec- trolley and its settings.
-
Page 11: Display Control
3.3.Display control To switch on the e-bike, press the button for one second. Use the same procedure to switch off. A 15-minute period of inactivity will result in an automatic switch-off. 3.3.1. Basic indicators 3.3.2. Pushing assistance When the e-bike is switched on, the TRIP (distance travelled) indicator is displayed To activate the push assist, briefly press the diffusely. -
Page 12: Switching On The Light
3.3.3. Switching on the light Hold the and the indicator button for one second to turn on the front light will appear . Use the same method to turn the light off again. 3.3.4. Level of assistance The e-bike offers 5 levels of riding assistance. "1" is the minimum and "5" is the maximum electric motor assistance. -
Page 13: Battery Charge Indicator
3.3.5. Battery charge indicator A full charge is indicated by 5 lines on the battery indicator, when the battery symbol is almost fully discharged it starts flashing. Flash (low voltage) Battery Indicator 3.3.6. Error indicator The bike's electrical functions are constantly monitored. In the event of an indication of a problem, the bottom of the Err and the error number appear on the display. -
Page 14: Technical Parameters
3.5. MOTOR The VINKA E40 motor is equipped with a pedal frequency sensor and a torsional pedal pressure sensor. The control unit (the brain of the electric motor), which is integrated into the motor body, evaluates the force and frequency with which the rider pedals and regulates the motor power accordingly. -
Page 15: Safety Information
4.Safety information 4.1. ENSURING SAFE OPERATION Conditions of operation EasyBike Promenade e-bikes are designed for use on normal roads and unpaved paths. Helmet Always wear a protective bicycle helmet. Even falls at low speeds can lead to fatal head injuries! Tyres Regularly check the tread wear and inflation of the tyres. -
Page 16: Maintenance
NOTICE Like other mechanical devices, an electric bicycle is subject to stress and wear during its active operation. Some materials and components may react to this load, causing material fatigue and subsequent damage. If the service life of a part has been exceeded, sudden failure can occur, which can cause injury to the rider. - Page 17 Transportation The battery does not need to be removed for transport in the car. In case of transport on the car, we recommend removing the battery. The electric bike can be transported on a bike rack, taking into account the total weight of the bike and the load capacity of the bike rack.
-
Page 18: Warranty Inspection
5.Warranty certificate warranty inspection 5.1.WARRANTY CONDITIONS The warranty provided for the bicycles and components sold by us lasts for 2 years from the date of sale indicated in the warranty document or on the invoice, unless otherwise stated below for selected components. The warranty can be applied to manufacturing and hidden defects in the product caused by the manufacturer or the seller, in particular manufacturing defects in materials or defects caused by imperfect technological processing. - Page 19 Forks: Defects such as looseness cannot be claimed if there is dirt and water inside the fork causing damage, or if the fork column is bent or the crown is damaged due to accidents and overloading. The condition for accepting a claim for a cracked suspension fork is that the geometry of the inner and outer legs is intact.
- Page 20 Pedals: The warranty covers manufacturing and material defects. Wear and tear caused by operation, loosening or breaking of cage joints or bending caused by impact or dropping are not covered by the warranty. Pedal noise and clearance adjustments cannot be accepted under warranty claims, but are subject to after warranty service.
- Page 21 The service coupon is then sent to the electric bike dealer. If the warranty inspection is not carried out within the above mentioned period, the warranty entitlement will expire. EasyBike e-bikes are subject to technical development, all information...
-
Page 22: Warranty Letter
(natural disasters, accidents and other circumstances vis maior) or if the product has been retrofitted in an unprofessional manner. On behalf of the LKQ CZ team we wish you many happy kilometres. Manufacturer of electric bikes EasyBike: LKQ CZ s.r.o., Ocelářská 16, Prague 9, 190 00, Czech Republic...
Need help?
Do you have a question about the PROMENADE and is the answer not in the manual?
Questions and answers