Gap Diagnostic EASControl User Manual
  1. Manuals
  2. Brands
  3. Gap Diagnostic Manuals
  4. Automobile Accessories
  5. EASControl
  6. User manual

Gap Diagnostic EASControl User Manual

Hide thumbs Also See for EASControl:
Table of Contents

Advertisement

Quick Links

Download this manual
EASControl And EASControl BT
for
All vehicles
By
User manual Version 23
Firmware V3.0
I1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EASControl and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Gap Diagnostic EASControl

Summary of Contents for Gap Diagnostic EASControl

  • Page 1 EASControl And EASControl BT All vehicles User manual Version 23 Firmware V3.0...
  • Page 2 Neither the distributors nor the manufacturer (GAP Diagnostic, Inc.) accept any responsibility or liability for damages incurred through use of the EASControl. This includes all damages to the vehicle itself, vehicle systems or property. This also includes injuries to the user or other persons.
  • Page 3 Those who use these procedures shall accept all responsibility for performing the work which may be described below. Specifi cations are subject to change without prior notice. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 4: Table Of Contents

    1.3.2 License policy ...................10 1.3.3 Warning messages ................10 1.4 Updating the EASControl fi rmware ..........11 1.5 Mobile App automated fi le loading / updating ....... 13 1.6 Mobile App demo mode (Android only at the current time) ..14 1.7 Connecting to the vehicle ..............
  • Page 5 3.2.2 Checking faults with an EASControl BT..........31 3.2.3 Advanced Read function. All except L322-02 .........32 3.2.4 Reading the fault output ..............34 3.2.5 Understanding diagnostic trouble codes (faults) ......36 3.3 Clear Fault..................38 3.4 Height ....................39 3.5 Calibration ..................41 Sensor calibration ....................41...

  • Page 6: Getting Started

    VIN : Vehicle Identifi cation Number. It’s a unique code which includes information’s about the vehicle’s confi guration and its serial number. DTC : For Diagnostic Trouble Code or fault code. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 7: Supported Vehicles Diminutive

    The vehicle model year can be found in the VIN. For example, in ...5DA123456, the 8th cha- racter starting from the right (654321AD) is a D which would be model year 2013 (1 = 2001, A=2010). GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 8: Introduction

    OS 4.3 or higher. For example, one user reported that a Chinese made Doogee phone cannot be used with our App. With fi rmware version 3.0, the EASControl has full diagnostic functionality for the EAS system only. Service routines can also be performed., live values viewing and control I/O and are included.

  • Page 9: License Policy

    EASControl covers. Advanced programming functions are VIN locked. Note: For clarity, only the name EASControl is used throughout this document except for items exclu- sively available on the EASControl BT. All characteristics of the EASControl are included in the EAS- Control BT.

  • Page 10: Updating The Eascontrol Fi Rmware

    1.4 Updating the EASControl fi rmware The following steps will allow updating the EASControl’s fi rmware to the latest available version. Updates are free for a period of one (1) year after the date of purchase. Log in to our website and follow these steps (picture) to download the updater software. Once fi...
  • Page 11 On rare occasions, a hardware or operating system confi guration can prevent the updater software from updating the EASControl. If it fails to connect to the unit when the «Find Device» button is pressed, please try again using another USB port, cable or PC / Mac.

  • Page 12: Mobile App Automated Fi Le Loading / Updating

    1.5 Mobile App automated fi le loading / updating This procedure is necessary when the App or EASControl fi rmware is updated. Step one and two are only necessary if the updater software used is older then V3.9. Disconnect EASControl...

  • Page 13: Mobile App Demo Mode (Android Only At The Current Time)

    Not all functions are implemented in demo mode. • Delays inherent in communicating with a vehicle are eliminated in the demo mode • Live values are arbitrary and do not refl ect real world conditions. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 14: Connecting To The Vehicle

    fi nisher on the driver’s side of the vehicle. Hinged cover must be opened for access. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 15: Accessing The Menu And Navgation

    Speed + / Menu Up and Speed - / Menu Down buttons to navigate up or down or change values. To exit the EASControl menu, use the Back button to navigate to the top level menu and press Back again or move the vehicle*. The message «Exiting Menu» confi rms that the session is terminated.

  • Page 16: Bt Mobile Interface

    Mobile Interface The EASControl BTcan be connected on an iPhone 4S and up, iPod Touch 5 and up, iPad Mini and iPad 3rd generation and up. It will also work on Android devices fi tted with a Bluetooth V4.0 transceiver and running on OS 4.3 or higher.

  • Page 17: Controls

    It does not provide any additional feature over the regular integrated or mobile interfaces. If not already installed, download and install the EASControl / EASControl updater software (Page 10, point 1).

  • Page 18: Integrated Interface Buttons Defi Nitions

    1.8.3 Integrated Interface buttons defi nitions L322-02, L322-06 The EASControl is controlled with the vehicle’s cruise control switchgear. The functions are: Resume = Enter* Speed + = Menu up / increase value Speed - = Menu down / decrease value...
  • Page 19 L319-10 The EASControl is controlled with the vehicle’s cruise control switchgear. The functions are: Set/Speed + = Menu up / increase value Resume = Enter* Cancel (CAN) = Back one level / Exit Set/Speed - = Menu down / decrease value Alternative set of controls L319-10.
  • Page 20 On L322-02, L322-06 and L319-04, the informations are displayed on a single line. On L319-10, the informations are displayed on three lines. Note for all vehicles When the following symbol is displayed <+>, the EASControl will continue the current process after the Speed + / Menu Up button is pressed.

  • Page 21: Activating The Eascontrol

    Using the mobile App to retrieve the activation code To activate the EASControl, you will need access to the exact vehicle it will be used on. Your mobile device will have to be connected on the internet. If not possible, you will have to fi ll up the form on our website using another device connected to the internet.

  • Page 22: Using The Integrated Interface

    1.9.2 Using the integrated interface To activate the EASControl, you will need access to the exact vehicle it will be used on. Once your activation code is noted, you will need an internet connection to get your unlock code. Turn the key to the ON position (II) or push Start. Ensure that the vehicle is in Park ( L319, or in Neutral with the handbrake applied for manual transaxle) and in a safe environment.

  • Page 23: Unlock Code Retrieval

    1.9.3 Unlock code retrieval Once logged into our website: Click on My Products Click on Product activation and Management Activate My Product GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 24 * If the advanced programming functions are needed on additional vehicles, please visit our website to buy additional VIN’s license(s). The VIN license code will be entered in this fi eld. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 25 Notes: If you do not receive your unlock code within a few minutes, please verify your junk folder. Free mail services like hotmail do sometimes consider our automated emails to be spam. If so, please add the following e-mail address to your trusted senders list: gapteam@gap-diagnostic.com GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 26: Backups And Other Post Unlock Notes

    1.9.5 First use ECU scan Upon fi rst use on a vehicle or after the tool fi rmware as been updated, the EASControl will scan the vehicle and note the presence of all ECU’s on communications buses. The resulting list is stored in the EASControl memory for up to 10 vehicles.

  • Page 27: Menu Tree

    L322-02 Menu tree GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 28 All except L322-02 GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 29: Main Menu Options

    This function shows the current fi rmware version in your EASControl. The EASControl enters the top level menu at ‘Read Fault’ and displays the fi rmware version when the Speed+ / Menu Up button is pressed. The version can also be viewed using the updater software.

  • Page 30: Checking Faults With An Eascontrol Bt

    3.2.2 Checking faults with an EASControl BT. This button will allow exporting the fault list When this button is pressed, the EASControl will proceed with a fault scan (‘‘refresh’’) This buttons clears faults Show all ECUs This menu is not relevent for the EASControl.

  • Page 31: Advanced Read Function. All Except L322-02

    Upon entering the function, the EASControl will ask if the fi rst status bit (bit 0, Test Failed?) is requi- red, press the Set + / Menu up to select this bit and Set - / Menu down to ignore it. The EASControl will then ask the same question for the second status bit and so on.
  • Page 32 Note: In some cases, faults will have both pending and confi rmed fl ags turned on. Since the confi rm fl ags prevails, the pending icon will not be shown. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 33: Reading The Fault Output

    ECU» or «scan and fi lter» functions will only show faults that are confi rmed. Use the «advance read» function to view non-confi rmed faults. List of status bits*: *Not implemented by Land Rover on L322-02 GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 34 By pressing Resume while viewing a fault, additional information will be displayed for 3 se- conds*. For the moment, the information displayed is the odometer value when the fault occurred. This feature is not available for all ECU’s and faults. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 35: Understanding Diagnostic Trouble Codes (Faults)

    ABS and DCS/HDC malfunction lights are ON. Performing a read faults using the EASControl or any other diagnostic tool may reveal many faults stored in different ECU’s. Hard faults (P,C or B) may create “lost communication” (U prefi x) errors because the ECU with the registered hard fault has stopped or is sending invalid data.
  • Page 36 Read and note the DTCs from every control modules. • Troubleshoot and correct the P, C or B fault(s). • Use the “Clear All” function of the EASControl. • Drive the vehicle normally. This will “test” if the problem(s) is or are resolved. •...

  • Page 37: Clear Fault

    Displays the ECU list and allows clearing of faults in one specifi c ECU. Scroll to the desired ECU and press Resume to enter. All faults stored in this specifi c ECU will be cleared. The EASControl automa- tically exits the menu afterwards (except when using the App).

  • Page 38: Height

    There is a severe risk of damaging components and the vehicle can become uncontrollable in this state! GAP Diagnostics assumes no liability for damages or injuries incurred during use or resulting from the use of the EASControl. •...
  • Page 39 The rear can be raised by a maximum of 200 - 180 = 20 mm. The rear can be lowered without a maxi- mum limit. The EASControl automatically calculates these values and allows only changes within these parame- ters. Note: The maximum values for lowering and raising are found by trial and error. They will not be the same on every vehicle.

  • Page 40: Calibration

    The settings and changes are given in millimeters but this does not correspond exactly to changes at the wheel. Each change in height must be measured from the bottom of the wheel arch to the center of the wheel (see step 5). GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 41 fl ashing), return to standard height and again wait for the LED to stop fl ashing. Move the vehicle forward 5 meters and back to its original position. Use the EASControl to take note of the actual calibration. Go to menu item ‘Live Values- > Suspension ECU- > Calibration’. Note down the values in the EAS Calibration Aid.
  • Page 42 *Please remember: when a value minus a negative value, the minus in the equation becomes a plus (subtracting a negative number = adding a positive number). For example, 3 - -3 = 6 GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 43 *Please remember: when a value minus a negative value, the minus in the equation becomes a plus (subtracting a negative number = adding a positive number). For example, 3 - -3 = 6 GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 44 If the ‘new calibration value left’ varies less than 3mm from the old calibration value it can be considered good. Otherwise navigate the EASControl to ‘Calibration- >Suspension-> Adjust Front Left’ or ‘Calibration- >Suspension-> Adjust Rear Left’ and use the Speed + / Menu up and Speed - / Menu down buttons to adjust the value to the ‘new calibration value left’.

  • Page 45: Service/Test

    PSC-550, CTEK MXS 25 or equivalent) to the battery when perfor- ming service routines. This will ensure that the battery voltage is suf- CAUTION fi cient. Note: Battery chargers are not suitable due to poor line regulation. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 46 Serious damage or injury can occur if a procedure is performed improperly! GAP Diagnostics assumes no liability for damages or injuries incurred during use or resulting from usage the EAS- Control. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 47: Test Valve

    The infl ation / defl ation continue as long as the button is held. The display shows the current height (relative to the standard height) while valves are activated in order to help see the height change and also confi rm the behavior of height sensors. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 48: Re-Enable Eas

    When removing a hose or a component, open connectors slowly and wait until the sound of escaping air ceases. Defective parts can pre- vent defl ation resulting in damage or personal injury. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 49: Set Tight / Normal Tolerance (All Except L322-02)

    Note: This function may cause error messages to appear on the instrument cluster display. It may also affect other vehicle systems. Upon exiting, the error will disappear. Use the same function to reactivate the air suspension. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 50: Live Values

    3.7.1 Defi nition This function allows viewing the current value or state of a sensor or actuator. For a complete list of live values for your vehicle, please consult the functionality list on the EASControl’s webpage. 3.7.2 Viewing live values when using the integrated interface To allow viewing of live values by the passenger, the value selected prior to driving the vehicle will stay displayed while the vehicle is on the move.

  • Page 51: Viewing Live Values When Using The Mobile App

    The cursor (far right dotted line) can be moved by swiping a fi nger over it. The live values data will be relative to it’s X axis position. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 52: Log Viewing And Exporting

    Logs can be manipulated (zoom, pan...) and exported in PDF, or CSV format. They can also be Air Printed. This button is used to export the selected log This button allows selecting which live values are displayed and exported. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 53: Graph View Options

    When only one Y axis is visible, an additional press will return to the initial layout (4 values in the following example). This was implemented to maximize the graph area. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 54 • Select the desired Y axis / live value • Touch and hold anywhere in the screen with 2 fi ngers and swipe verti- cally in opposite directions. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 55 To re-initialise the zoom view, touch the screen twice at one of the following locations: • On the currently selected Y axis. • On the X axis. • In the middle of the graph screen to reinitialize all axis simultaneously. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 56: Using The My Favorite Feature

    In this example, 3 live values are selected. The Load button is used to recall the last saved selection from the list. All 3 live values will be se- lected at once. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 57: Using The Trigger Feature

    The recording will include all data for all live values received X seconds after the stop trigger occurred. This is the target value. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...
  • Page 58 The buzzer will not be heard if the device volume is low or muted. All examples show live values available on the EASControl. The method is the same for suspension live values. GAP Diagnostic 2015-11-11 All right reserved...
  • Page 59 The live value increases and passes the event target of 20 %. • Recording begins and the previous data is kept (2 seconds) • Recording continues for 2 seconds GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 60: Control I/O

    Resume / Enter to apply. For example, a ventilation motor can be activated at dif- ferent speeds from 0 to 100%. This is self explanatory when using the mobile App. GAP Diagnostic 2015-11-11 All right reserved User manual: Version 23, Firmware V3.0...

  • Page 61: Save Restore

    3.9 Save Restore 3.9.1 Defi nition Upon activation, the EASControl makes a backup of the original EAS calibrations. These can be recal- led if needed. There are also 3 memory slots to save EAS calibration settings per vehicle. These can be used, for example to save the calibration settings for larger tires, normal tires, etc.

  • Page 62: Eascontrol Confi G

    The resulting list is stored in the EASControl memory for up to 10 vehicles 3.10.2 Voltage displayed When this feature is enabled, the EASControl is connected and the user has not called up the EAS- Control menu, the battery voltage will be displayed. 3.10.3 Enter unlock code You can unlock the advanced programming functions on your EASControl for future uses on other vehicles by entering an unlock code here.

  • Page 63: Limited Warranty

    The warranty is limited to the functionality of the sys- tem and the system itself. It is the user’s responsibility to use the EASControl safely. The user must return the EASControl to GAP Diagnostic to have the warranty honored. The user must provide a proof of purchase.

This manual is also suitable for:

Eascontrol bt

Table of Contents