Related Manuals for Asus VG247QR1A
Summary of Contents for Asus VG247QR1A
- Page 1 Monitor Service Manual Model: VG247QR1A Version no. V00 Release date: May.17, 2024 ...
- Page 2 ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement. This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.
- Page 3 Table of Contents 1. Safety Precautions ..............................4 2. Exploded View ..............................5 3. Disassembly & Assembly SOP ..........................7 4. Trouble shooting ..............................23...
-
Page 4: Safety Precautions
1. Safety Precautions Safety information Before setting up the monitor, carefully read all the documentation that came with the package. To prevent fire or shock hazard, never expose the monitor to rain or moisture. Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury. -
Page 5: Exploded View
2. Exploded View ... - Page 6 ASUS Description MIDDLE_FRAME LENS SCREW 3 4 PANEL SCREW M3 6 KEY BOARD POWER BOARD MAIN BOARD SCREW D3 6 SCREW M4 6 INSULATING SHEET 137X94X0.43 MAINFRAME SPEAKER INSULATING SHEET 86*50*0.25...
-
Page 7: Disassembly & Assembly Sop
3. Disassembly & Assembly SOP 3.1. Precaution Please read the precautions as follows to prevent any damages to the LCD Monitor. Make sure all power connection is removed. Be sure that the LCD Monitor is in power off status. Prepare soft cloth and sponge as working platform to place LCD monitor horizontally. - Page 8 Information in this section is to perform the disassembly procedure of the LCD monitor. Depending on the failures, replace the defective parts accordingly. ASUS VG247QR1A LCD monitor consists of various subsystems. This section describes the procedures for LCD monitor disassembly. In addition, the detailed disassembly procedures of individual subsystem will be provided for your service needs.
- Page 9 4.3.2 Main Subsystem 1. Release the screw. Use disassembly tool to open all the latches along the edge of the Rear Cover. (Note: Start to open the latches from bottom. Please operate in sequence as below until separate the panel from rear cover. Don’t damage the key board.) Description Q’ty...
- Page 10 4 2 3 1 2. Gently open the rear cover. Tear off the tape and disconnect the pin to remove the rear cover. ...
- Page 11 Key board and Speaker Disconnect the pins and remove the speaker. Release the screws to remove the key board from the rear cover. Description Q’ty Screw Torque Picture &Spec 4±1kgf.cm Screw(Rear cover/key board) ...
- Page 12 MAIN_FRAME 1. Tear off the tapes and disconnect cable. 2. Tear off the tape and disconnect the pins to remove the main frame. ...
- Page 13 3. Remove the Mylar. Main Board & Power Board 1. Release the screws marked in red, purple and green. Description Q’ty Screw Torque Picture &Spec Screw-Red(main 6±1kgf.cm board/power board/main frame) Screw-blue 6±1kgf.cm (power board/ main frame) ...
- Page 14 2. Turn over the Main Board and the Power Board and then disconnect the cables. 4.3.3 Panel 1. Release screws to separate the panel & the middle frame. Description Q’ty Screw Torque Picture &Spec...
- Page 15 ...
- Page 16 3.4 Assembly Procedure 3.4.1 Panel 1. Prepare the panel and middle frame. Use a screwdriver to tighten the screws. Description Q’ty Screw Torque Picture &Spec Screw-red(middle 3±0.5kgf.cm frame/panel) ...
- Page 17 3.4.2 Main subsystem Main board & Power board 1. Prepare a main frame, a main board, a power board and some essential cables. Connect every pins as below. 2. Use a screwdriver to tighten the screws. Put on the mylar. Description Q’ty Screw Torque...
- Page 18 Main frame 1. Put the main frame on panel. Connect the pins and paste the tapes. ...
- Page 19 Key board & Speaker 1. Assemble the key board. Use a screwdriver to tighten the screws. Description Q’ty Screw Torque Picture &Spec 4±1kgf.cm Screw(Rear cover/key board) ...
- Page 20 2. Assemble the speaker. Connect the pin and paste the tapes. Assemble the rear cover and panel Connect the pins and paste the tape. And then assemble the rear cover. Use a screwdriver to tighten the screw. Description Q’ty Screw Torque...
- Page 21 3.4.3 Stand Subsystem Tighten the screw to assemble the stand ass’y and base ass’y. Assemble the stand-base ass’y to monitor. Use a screwdriver to tighten the screws. Description Q’ty Screw Torque Picture &Spec...
- Page 22 M6*17 ...
-
Page 23: Trouble Shooting
4. Trouble shooting ...
Need help?
Do you have a question about the VG247QR1A and is the answer not in the manual?
Questions and answers