Related Manuals for Extreme Networks XEN-R000294
Summary of Contents for Extreme Networks XEN-R000294
- Page 1 HARDWARE INSTALLATION GUIDE Universal Two-Post Rack Kit Supporting XEN-R000294 53-1002943-07 Rev AA August 2019 *53-1002943-07 Rev AA*...
- Page 2 Legal Notice Extreme Networks, Inc. reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made.
-
Page 3: Table Of Contents
Contents Preface..............................................5 Conventions..................................................5 Notes, cautions, and warnings........................................5 Text formatting conventions......................................... 5 Command syntax conventions........................................6 Documentation and Training..........................................6 Training..................................................6 Getting Help................................................. 6 Subscribing to Service Notifications......................................7 Providing Feedback to Us............................................7 Universal Two-Post Rack Kit Installation..................................9 Introduction...................................................9 Safety precautions ..............................................9 Time and items required............................................ - Page 4 Universal Two-Post Rack Kit 53-1002943-07 Rev AA...
-
Page 5: Preface
Getting Help..........................................6 • Providing Feedback to Us....................................7 ® This section discusses the conventions used in this guide, ways to provide feedback, additional help, and other Extreme Networks publications. Conventions This section discusses the conventions used in this guide. Notes, cautions, and warnings Notes, cautions, and warning statements may be used in this document. -
Page 6: Command Syntax Conventions
Training Extreme Networks offers product training courses, both online and in person, as well as specialized certifications. For more information, visit www.extremenetworks.com/education/. Getting Help If you require assistance, contact Extreme Networks using one of the following methods:... -
Page 7: Subscribing To Service Notifications
Providing Feedback to Us Quality is our first concern at Extreme Networks, and we have made every effort to ensure the accuracy and completeness of this document. We are always striving to improve our documentation and help you work better, so we want to hear from you! We welcome all feedback but especially want to know about: •... - Page 8 Universal Two-Post Rack Kit 53-1002943-07 Rev AA...
-
Page 9: Universal Two-Post Rack Kit Installation
Introduction Use the following instructions to install an Extreme 1U or 2U device in a two-post telecommunications (Telco) rack using the Universal Two-Post Rack Kit (XEN-R000294). There are two ways you can mount the device in a two-post rack: •... -
Page 10: Time And Items Required
The following items are required to install the device using the Universal Two-Post Rack Kit: • #2 Phillips torque screwdriver • 1/4-inch slotted-blade torque screwdriver Parts list The following parts are provided with the Universal Two-Post Rack Kit Installation (XEN-R000294). Universal Two-Post Rack Kit 53-1002943-07 Rev AA... -
Page 11: Flush-Front Mounting
Flush-front mounting FIGURE 1 Rack kit parts Front brackets (2) Screw, 8-32 x 5/16-in., flathead Phillips (16) Rear brackets, 3-5 inch post (2) Screw, 6-32 x 1/4-in., panhead Phillips (8) Rear brackets, 5-6 inch post (2) Screw, 10-32 x 5/8-in., panhead Phillips (8) Screw, 8-32 x 5/16-in., panhead Phillips (8) Retainer nut, 10-32 (8) Ensure that the items listed and illustrated above are included in the kit. -
Page 12: Attaching The Front Brackets To The Device
Flush-front mounting Attaching the front brackets to the rack on page 12 Attaching the rear brackets to the rack on page 13 Attaching the rear brackets to the device on page 14 Attaching the front brackets to the device Complete the following steps to attach the front brackets to the device. Position the right front bracket with the flat side against the right side of the device, as shown in Figure Insert four 8-32 x 5/16-in. -
Page 13: Attaching The Rear Brackets To The Rack
Flush-front mounting Attach the left front bracket to the left rack upright using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use the upper and lower holes in the bracket. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb. (29 cm-kg). FIGURE 3 Attaching front brackets to a rack Screws, 10-32 x 5/8-in., panhead Phillips Retainer nuts, 10-32... -
Page 14: Attaching The Rear Brackets To The Device
Flush-front mounting Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb. (29 cm-kg). FIGURE 4 Attaching the rear brackets to a rack Retainer nuts, 10-32 Screws, 10-32 x 5/8-in., panhead Phillips Rear brackets Attaching the rear brackets to the device Complete the following steps to attach the rear brackets to the device. -
Page 15: Mid-Mounting
Mid-mounting Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg). FIGURE 5 Attaching the rear brackets to the device Screws, 8-32 x 5/16-in., panhead Phillips Mid-mounting Observe the following notes when using this procedure: •... -
Page 16: Attaching The Front Brackets To The Rack
Mid-mounting Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and then into the holes on the side of the device. Use the upper and lower screw holes, leaving the center holes empty. Repeat step 1 and step 2 to attach the left front bracket to the left side of the device. Tighten all the 8-32 x 5/16-in. -
Page 17: Attaching The Rear Brackets To The Rack
Mid-mounting Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg). FIGURE 7 Attaching front brackets to a rack Screws, 10-32 x 5/8-in., panhead Phillips Retainer nuts, 10-32 Attaching the rear brackets to the rack Complete the following steps to attach the rear brackets to the rack. -
Page 18: Attaching The Rear Brackets To The Device
Mid-mounting Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg). FIGURE 8 Attaching the rear brackets to a rack Retainer nuts, 10-32 Screws, 10-32 x 5/8-in., panhead Phillips Rear brackets (right and left) Attaching the rear brackets to the device Complete the following steps to attach the rear brackets to the device. - Page 19 Mid-mounting Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg). FIGURE 9 Attaching the rear brackets to the device Screws, 8-32 x 5/16-in., panhead Phillips Universal Two-Post Rack Kit 53-1002943-07 Rev AA...
Need help?
Do you have a question about the XEN-R000294 and is the answer not in the manual?
Questions and answers