Advertisement
OPERATION & MAINTENANCE
MANUAL
BEAVER TECHNOLOGY SERVICES
PTY LIMITED
BTS
®
TRIPOD ASSEMBLY
Part No. BTS40014
This product has been successfully tested to AS/NZS 5532:2013
& EN795 and complies with the Basic Health & Safety
requirements of European Directive 89/686/EC
SAFETY SYSTEMS
AS/NZS 5532:2013
2797
FS603922
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for BTS PRO-3
Summary of Contents for BTS PRO-3
- Page 1 OPERATION & MAINTENANCE MANUAL SAFETY SYSTEMS ® TRIPOD ASSEMBLY Part No. BTS40014 This product has been successfully tested to AS/NZS 5532:2013 & EN795 and complies with the Basic Health & Safety requirements of European Directive 89/686/EC AS/NZS 5532:2013 2797 BEAVER TECHNOLOGY SERVICES FS603922 PTY LIMITED...
-
Page 2: Table Of Contents
OPERATION & MAINTENANCE MANUAL Pro-3 TRIPOD ASSEMBLY ® TABLE OF CONTENTS PARTS IDENTIFICATION 1. System Introduction See Figure 1 (below) for parts identifi cation. 2. Application 3. General System Requirements 4. System Installation 5. Training 6. Inspection 7. Packaging Top Pulley 8. - Page 3 This Tripod is constructed of high quality aluminum 6061-T6 tubing for ease of mobility, and features the BTS Spring Pin connections for ease of set-up and dismantle. The Tripod may be equipped with a variety of winches, SRL’s and other accessories, depending on your requirements.
-
Page 4: Application
The Tripod, when equipped with BTS PRO Series Winch or Type 3 device, may be used as part of a system to facilitate access to and egress from a confi ned space as well as non-entry rescue in the event of an emergency. When used with a BTS Pro- Series winch, this Tripod meets the requirements of AS/NZS 5532:2013, EN795 and CEN/TS16415 for use as a confi... -
Page 5: General System Requirements
• The Tripod system is suitable for a single user to be attached at any one time. Check system specifi cations or contact BTS for confi guration limitations. Operator of the winch or Type 3 SRL is to be connected to an anchor point on the tripod. -
Page 6: System Installation
STEP: 4 4.2 Tripod Accessory Installation For accessories not supplied by BTS, the competent person is responsible for the design, installation, use and compatibility of the system with the Pro-3 Tripod. The competent person responsible must provide detailed information regarding the installation of the accessory onto the system. - Page 7 BTS-Klicks are fully engaged. Secure it with the locking pin. (Please note that some systems are fi tted with a rail that is permanently bolted together and requires a one-time assembly).
-
Page 8: Training
fi nish. • Using a moisture displacing penetrating lubricant, lubricate the BTS Spring Pins, Tripod leg and foot pad pivot point and the Pulley assembly. -
Page 9: Packaging
OPERATION & MAINTENANCE MANUAL Pro-3 TRIPOD ASSEMBLY ® • Inspect the Tripod to check if there are any signs of a fall that might have occurred. • If used with a Winch, ensure the Winch bracket is secure to the Tripod leg. Use Winch operational/inspection manual for its inspection and maintenance. -
Page 10: Labels & Markings
OPERATION & MAINTENANCE MANUAL Pro-3 TRIPOD ASSEMBLY ® 8. LABELS & MARKINGS Danger L BEAVER TECHNOLOGY SERVICES BTS PRO-3 Product ID Lab PRO-3 Tripod Assembly Manufactured by: BEAVER OSHA LUBRICATION TECHNOLOGY SERVICES Please refer to Operator’s Manual for instructions Compliant... - Page 11 (other than implied by statue which may not be excluded) with respect of the information. By using this information, the user undertakes not to hold BTS liable or responsible in any way whatsoever in relation or consequential to such use.
- Page 12 BEAVER TECHNOLOGY SERVICES CAUTION PTY LIMITED FS603922 Read Instruction Manual before using. www.btstech.com.au © Copyright Beaver Technology Services Pty Limited 11/2021 BØC - TS - Pro-3 Tripod Assembly BTS40014-EU Rev_3...
Need help?
Do you have a question about the PRO-3 and is the answer not in the manual?
Questions and answers