Advertisement
Quick Links
MS-700 OPTIMUM
QUICK START GUIDE
Power/Status
Indicator LEDs
Line Output
IP Address
Line Input
LCD Screen
AMPLIFIER
Line Input
Remote Control Ports
Speaker
PA
WPA-70x Input/Output
Connections
Mute
USB Port
PoE+ Network Port
XD Link
Reboot/Factory Default
Link Button
Link Light
Microphone 2 Status
System Power Status
Microphone 1 Status
Advertisement
Related Manuals for Audio enhancement MS-700 OPTIMUM AMPLIFIER
Summary of Contents for Audio enhancement MS-700 OPTIMUM AMPLIFIER
- Page 1 MS-700 OPTIMUM AMPLIFIER QUICK START GUIDE Power/Status Indicator LEDs Line Output Line Input Remote Control Ports USB Port PoE+ Network Port IP Address Line Input Speaker WPA-70x Input/Output XD Link Reboot/Factory Default LCD Screen Connections Mute Link Button Link Light Microphone 2 Status System Power Status Microphone 1 Status...
-
Page 2: Functional Summary
DESCRIPTION MS-700 Optimum Amplifier is a fully integrated networked classroom amplifier and wireless microphone receiver. This amplifier has network-based intercom, paging and emergency notifications, and provides full-duplex audio. It is easy-to-use, easy-to-install, and has a simple user interface software. The entire unit utilizes Power over Ethernet (PoE+). Intercom and paging functionalities are built-in. When used in conjunction with an Uninterruptable Power Supply (UPS), during emergencies, paging can still be heard, even when the power goes out. - Page 3 Also Connects to the ITC2 • Microphone 2 Status - Green when • connected to mic WALL PLATE AUDIO (WPA) PORT Power LED Connects to Audio Enhancement Wall Plates • Red while booting • Green when operational • IO PORT (GPIO 3 & 4)
- Page 4 PA MUTE Audio is muted when 5-70VAC is present • POE+ ETHERNET IEEF 802.3 at required • RESET BUTTON CONFIGURATION SET UP IN EPIC Follow the instructions in the EPIC System Admin Manual - Managing Devices. Click or Scan QR code to access. XD TEACHER MICROPHONE VOLUME CONTROL Press SELECT to choose the desired source to control.
- Page 5 XD TEACHER MICROPHONE LINKING With the microphone off, press the With the microphone off, press and hold Link button on the front of the amplifier REC button. Then promptly press and (Look for the blinking yellow LED). hold PWR until microphone is linked. Successful microphone linking will produce a beep through the system, and on the front of the amplifier you will see an additional green LED.
- Page 6 XD STUDENT MICROPHONE LINKING With the microphone off, press the Link Press and hold the PWR LINK button on the front of the amplifier. button on the back of the XD (Look for the blinking yellow LED) Student Microphone. While holding the PWR LINK button, use your thumb to slide the TALK button up into the on position.
- Page 7 LINKING THE MEDIA CHANNEL The microphone cannot be linked to the Media channel unless MIC 1 and MIC 2 channels are on. Make sure the microphone needing to be linked, either the Teacher or Student, is turned off. Confirm that both Channel 1 and Channel 2 mics are on and connected to the amplifier. Follow XD Teacher or XD Student Microphone Linking section instructions.
-
Page 8: Connector Details
CONNECTOR DETAILS NOTE Some pinouts for the MS-700 are different than the MS-600. RMTCTRL PORTS WALL PLATE AUDIO +Line Level Output +Mic -Line Level Output -Mic RS232 - TXD I/O In #1 (Call) +24V dc +24V dc RS232 - RXD I/O In #2 (Emergency) +Line Level Input I/O IOut #1... -
Page 9: Troubleshooting
TROUBLESHOOTING REBOOT BUTTON FUNCTIONALITY Reboot Press and hold button (5 seconds). Factory Reset Procedure Press and hold for 10 seconds wait for Status LED to flash green and release. REBOOTING ISSUE If MS-700 is constantly rebooting and has peripherals plugged in, such as an ITC, it might be pulling too much power.
Need help?
Do you have a question about the MS-700 OPTIMUM AMPLIFIER and is the answer not in the manual?
Questions and answers