Advertisement
Quick Links
DC-6000 Dust Collector
WARNING
Read the SAFETY section and Complete
the ASSEMBLY procedures before oper-
ating the Shopsmith Dust Collector.
T T T T T a a a a a b b b b b le of
le of
le of
le of Contents
le of
Contents
Contents
Contents
Contents
Parts List ...................................................... 2
Introduction/Safety .................................... 4
General Information ................................... 7
Assembly ..................................................... 8
Maintenance and Troubleshooting ........ 13
556700
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Shopsmith DC-6000
Summary of Contents for Shopsmith DC-6000
- Page 1 Contents Contents Contents Contents WARNING Parts List ............2 Introduction/Safety ........4 Read the SAFETY section and Complete General Information ........7 the ASSEMBLY procedures before oper- Assembly ............. 8 ating the Shopsmith Dust Collector. Maintenance and Troubleshooting ..13...
- Page 2 Handle ............1 521762 Screw ............2 515555 Self-Tapping Screw ....... 6 515553 Cable Clip ..........1 515219 Bag Clip ............ 3 Manufacturer: Shopsmith 6530 Poe Avenue Dayton, Ohio 45414 937-890-5197 556700 Part Number: Description: Shopsmith Air FIltration System DC-6000 Page 2...
- Page 3 556700 Dust Collector Figure 1 Page 3...
- Page 4 Shopsmith Dust Collector can be “observed” by placing a few fingers into the • Keep work areas well lit, clean, and free from end of the hose. The airflow of the Shopsmith clutter. Dust Collector is much higher than any home or shop vacuum.
- Page 5 Collector maintained according to the Owners opening and into contact with the fan. Manual. • Do not pick up water or wet materials with the • Use only recommended Shopsmith parts and Dust Collector. accessories on your Dust Collector. NEVER use non-Shopsmith replacement •...
- Page 6 Therefore, it should not be run on the Do not modify the plug. If it will not fit the outlet, have • same circuit as the Shopsmith MARK 7 or Mark V as the proper outlet installed. you could over-load the circuit.
- Page 7 556700 Dust Collector General Information Terms to Know Dust Collector Attachment Kit: The main parts of the Dust Collector are: 10. Hose (1) - Connects to the 3-way inlet. Bag - A heavy duty, disposable, 4 mil., 11. Inlet Plug Assemblies (2) - Placed in clear plastic bag.
- Page 8 Place a block of wood or a book under ® mark ( )after the word “Shopsmith” on the housing so it doesn’t roll. the legs should be near the larger (See Figure 4). diameter end (top) of the main housing.
- Page 9 556700 Dust Collector Install the Base Pan Install the Rear Wheels 6. The Base (46) comes with the Wheel Shaft NOTE: The procedure below shows (45) pre-installed. Lay a 2 x 4 under the inserting the screws through the legs and end of the Wheel Shaft (45).
- Page 10 Dust Collector 556700 Tighten the Leg Screws Install Snap-in Plugs and Left Leg Cap 10. Using a 1/2" socket and ratchet wrench to 13. Insert the snap-in plugs (39) into the four hold the nuts (42), tighten the leg screws round holes in the side of each leg.
- Page 11 Turn the filter the way around. hood so the strap clamp is centered at the back of the housing and the Shopsmith Logo on the front of the filter hood is centered with the 3-Way Inlet in front.
- Page 12 2-1/4" dust chute outlets. An optional the open inlet. reducer allows you to connect to equipment with 1-1/4" chutes such as the Shopsmith 27. Plug the Dust Collector into a wall socket. Mark V Model 500 (having a serial number Refer to the section, “Electrical...
- Page 13 556700 Dust Collector Caring for Your Dust Collector Your Dust Collector is designed to deliver years of reliable service with a minimum of maintenance. Cleaning the Filter Hood During operation, dust will build up on the inside surface of the filter hood. Every time the bag is changed, tap the top and sides of the filter hood to dislodge the dust buildup.
- Page 14 NOTE on your machine). To keep them handy, please write in the alloted spaces below. If you have any questions about your Shopsmith DC-6000, please call our Customer Customer No: Service Department at (937)890-5197, send us an e-mail at customerservice@shopsmith.com, Date Code: or visit our website at www.shopsmith.com.
Need help?
Do you have a question about the DC-6000 and is the answer not in the manual?
Questions and answers