Advertisement
Advertisement
Table of Contents
Related Manuals for Spypoint FORCE-PRO-S 2.0
Summary of Contents for Spypoint FORCE-PRO-S 2.0
- Page 1 FORCE-PRO-S 2.0 Quick Start Guide v1.3...
- Page 2 FORCE-PRO-S 2.0 32GB INSTALLATION CHARGING STRAP CABLE NOTE The FORCE-PRO-S 2.0 has an internal battery that can be charged using the supplied cable. The use of additional AA batteries is optional. User Manual, software updates & FAQs available at: www.spypoint.com/support.
- Page 3 COMPONENTS No glow flash Screw-thread for standard 1⁄4”-20 Red LED indicator LCD screen Photo lens OK button Detection lens Navigation buttons Cable lock hole Switch ON/SETUP/OFF Slot for installation strap SD card slot Locking latch Battery compartment 12 V jack Solar Panel...
- Page 8 0 MP 35:20 6/02121) press OK ge camera settings on mode s to allow you to move away. ndicates the camera is ready. Charge camera using the for approximately 12 h before ge status by entering"SETUP" battery indicator.
- Page 9 8AA alkaline or lithium batteries You can use any combination of the above power sources with your FORCE-PRO-S 2.0. If multiple power sources are connected, the camera will use them in the following order: Internal Battery, 12V, and then the AA.
-
Page 10: Installing An Sd Card
FOR MAXIMUM PERFORMANCE ND WITHOUT LEAKING BATTERIES • Use new batteries. • Use ONLY alkaline or ONLY lithium batteries. • Do not mix new and old batteries. • Do not use rechargeable AA batteries, as their lower voltage may cause operating difficulties. INSTALLING AN SD CARD The camera was designed to operate with an SD card between 2 and 512 GB of memory. - Page 11 FORMAT YOUR SD CARD Upon inserting your SD Card, navigate to the settings option and follow the on screen menu options to format your SD Card. See section OTHER OPTIONS for an explanation of the formatting process. GENERAL SETTINGS SETUP Use the...
-
Page 12: Video Mode
SETUP ADJUST THE SETTINGS FOR THE 4 MODES OF OPERATION PHOTO MODE Delay: Allows you to select the time elapsed before the camera can detect again and take the next photo. If you want to capture multiple photos, use a shorter delay. Once you have selected the delay, press OK. - Page 13 Length*: Allows the user to choose the video length (10 to 60 s). Once you have made your selection, press OK. Detect: Allows you to set motion-detector sensitivity (LOW, NORMAL, HIGH, AUTO). Once you have made your selection, press OK. TIME-LAPSE Allows you to take photos at regular predefined intervalswithout necessarily detecting a movement.
-
Page 14: Additional Options
Multi: Allows you to select the number of photos to be taken per shot (from 1 to 6 photos). Once you have made your selection, press OK. Detect: Allows you to set motion-detector sensitivity (LOW, NORMAL, HIGH, AUTO). Once you have made your selection, press OK. -
Page 15: Operation
OPERATION Once the setup is complete, turn the button from SETUP to ON. You may also switch from SETUP to OFF and turn the device ON later. RED LIGHT ON THE FRONT OF THE CAMERA When the switch is in the SETUP position, the red light will flash to confirm a motion detection once you have adjusted your settings. -
Page 16: Installation
INSTALLATION Recommended height of installation: The camera must be installed at the height of the centre line of the animal’s body. Ideal setup for high-quality images and videos: The target animal should be 7.5 m from the camera to get a better line of sight. - Page 17 Scan for detailed instructions, LED light pattern descriptions, complete user manual & other helpful information : spypoint.com/FORCEPROS2-guide Need assistance? Just contact us! INTERNATIONAL CAN/US spypoint.info/en/support-2/ spypoint.com/support +49 (0) 36331-403333 1-888-779-7646 2-year limited warranty, visit spypoint.com/garantie for complete details. Made in China...
- Page 18 FORCE-PRO-S 2.0 More information available in the certifications guide...
Need help?
Do you have a question about the FORCE-PRO-S 2.0 and is the answer not in the manual?
Questions and answers