Table of Contents
Advertisement
Quick Links
SIP Industrial Products
SIP Industrial Products
Limited Gelders Hall Road
Limited Gelders Hall Road
Shepshed
Shepshed
Loughborough
Loughborough
Leicestershire
Leicestershire
LE12 9NH
LE12 9NH
United Kingdom
United Kingdom
For help or advice please contact
your distributor, or sip directly on:
Tel.: 01509 500400
Email:
sales@sip-group.com
or
customerservice@sip-group.com
www.sip-group.com
Fireball RP35 Radiant
Propane Heater
Please read and fully understand the instructions in this manual
before operation. Keep this manual safe for future reference.
SIP Code 09315
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SIP Fireball RP35
Summary of Contents for SIP Fireball RP35
- Page 1 LE12 9NH Fireball RP35 Radiant United Kingdom United Kingdom Propane Heater For help or advice please contact your distributor, or sip directly on: Tel.: 01509 500400 Email: sales@sip-group.com SIP Code 09315 customerservice@sip-group.com Please read and fully understand the instructions in this manual www.sip-group.com...
- Page 2 INTRODUCTION Thank you for purchasing this SIP Radiant Gas Heater. designed for industrial use only, i.e. NOT for domestic use. This portable gas heater is designed to BS 4096 for industrial applications, to give safe, efficient and reliable operation, and is for use with Propane Gas only. Propane gas bottles are not supplied with the unit, but are readily available from builders merchants or gas suppliers.
- Page 3 THE FOLLOWING TABLE ADDRESSES THE INFORMATION REQUIREMENTS OF REG.2015/1188 Item Symbol Value Unit Fuel LPG butane Gaseous [mg/kWh ] (GCV) input Space Heating Emission(*) Indirect heating fuctionality: [yes/no] Heat Output At nominal heat output Pnom At minimum heat output (indicative) 1.55 Pnom Auxiliary electricity consumption...
-
Page 4: General Safety Precautions
GENERAL SAFETY PRECAUTIONS Read, and make sure you fully understand the following precautions and the hazards associated with this type of equipment. 1. Check the heater thoroughly for damage. DO NOT operate a damaged heater. 2. DO NOT modify the heater or operate a heater which has been modified from its original condition. -
Page 5: Minimum Clearances From Combustibles
MINIMUM FRESH AIR OPENING REQUIREMENTS • Do not use in unventilated areas. • The flow of combustion and ventilation air must not be obstructed. Warning: PROVIDE AT LEAST 3FT OPENING OF FRESH, OUTSIDE AIR WHILST RUNNING THIS HEATER. IF PROPER FRESH OUTSIDE AIR VENTILATION IS NOT PROVIDED, CARBON MONOXIDE POISONING CAN OCCUR. - Page 6 IF YOU SMELL GAS NO ODOUR DETECTED LP gas and natural gas have man-made odorants added specifically for detection 1. Some people cannot smell the odour of fuel gas leaks. added to propane (LP) or natural gas. If a gas leak occurs you should be able to You must determine if you can smell smell the fuel gas.
-
Page 7: Gas System
FEATURES OF THE 09315 RP35 RADIANT HEATER Understanding the basic operation of the heater will reinforce the need to maintain the unit in top condition at all times whilst always observing the safety precautions. The heater comprises three basic systems: 1. -
Page 8: Locating The Heater
The replacement hose assembly shall be that specified by the SIP Industrial Products. UNPACKING 1. Remove heater from carton. 2. Remove all protective material which may have been applied to the heater for shipment. -
Page 9: First Use
IMPORTANT: The gas hose and cylinder must ALWAYS be located behind the machine - at a distance of at least 6 feet. In order to reduce the risk of icing up, when operating at long periods of maximum capacity, you should use a larger capacity gas bottle or two/three bottles in parallel, as shown. - Page 10 soap and water solution. NEVER use a match to check for gas leaks. When satisfied, open the valve on the gas cylinder. NOTE: The heater, has a fixed, regulated gas flow. 2. Press and hold the control valve plunge as shown whilst continually pressing the piezo-electric button until the burner ignites.
-
Page 11: Cleaning And Maintenance
lighting pilot. New installations generally require bleed of supply lines. Wait a minimum of five minutes after bleeding supply lines before attempting to light heater. CAUTION: THIS APPLIANCE IS HOT DURING NORMAL OPERATION. AVOID PHYSICAL CONTACT. DO NOT PLACE CLOTHING OR OTHER COMBUSTIBLE MATERIALS ON THIS APPLIANCE. -
Page 12: Troubleshooting
TROUBLESHOOTING Fault Cause Remedy Burner fails to light 1. Gas supply valve 1. Open gas supply valve slowly closed. 2. Close propane supply valve 2. Excess-flow check closed propane tank and re- valve. open slowly. 3. Excess-flow check 3. Replace burner orifice. valve. -
Page 13: Specification
Fault Cause Remedy Heater stops dur- 1. Excessive gas supply. 1. Check the pressure regulator ing operation. 2. Insufficient gas supply and replace if necessary. due to ice formation 2. Check & use larger cylinder, on the cylinder. or two or more in parallel. 3. -
Page 14: Parts Diagram
PARTS DIAGRAM PARTS LIST Burner 115286-01 Tip Switch 115285-01 Thermocouple 114121-01 Brass Elbow 111090-02 Bracket 117384-01 Hose/Regulator 115290-04 Igniter Electrode 115291-01 Wheel 115292-01 Igniter Bracket 117385-01 Wheel Bracket 114156-02 Piezo-Igniter Kit 102445-01 Wheel Lock 115294-01 Orifice 115287-01 Main Frame Assy 117297-01 Valve 115285-01... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY... - Page 16 This will allow the recycling of raw materials and help protect the environment. For help or advice please contact your distributor, or sip directly on: Tel.: 01509 500400 Email: sales@sip-group.com customerservice@sip-group.com www.sip-group.com...
Need help?
Do you have a question about the Fireball RP35 and is the answer not in the manual?
Questions and answers