Sumitomo JR-6+ Manual To Operation
  1. Manuals
  2. Brands
  3. Sumitomo Manuals
  4. Industrial Electrical
  5. JR-6+
  6. Manual to operation
Sumitomo JR-6+ Manual To Operation

Sumitomo JR-6+ Manual To Operation

Hot jacket remover
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OME1826029B
Hot jacket remover
JR-6+
Guide to operation

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JR-6+ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sumitomo JR-6+

Summary of Contents for Sumitomo JR-6+

  • Page 1 OME1826029B Hot jacket remover JR-6+ Guide to operation...
  • Page 2 OME1826029B...

  • Page 3: Important Safety Precautions

    OME1826029B immediately turn off the power. Next, IMPORTANT SAFETY PRECAUTIONS contact maintenance service This product been designed center. manufactured assure personal safety. 4. Do not touch the heat plate during use. Improper use can result in bodily injury and The heat plate and its peripheral parts serious damage to the jacket remover.
  • Page 4 Handle battery life expectancy. with care. 14. Make sure polarities are correctly 3. Blades are consumables. Only use connected. Do not attempt to connect Sumitomo genuine blades the battery module when you cannot replacement. Always replace...

  • Page 5: Table Of Contents

    Battery level check ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Charging the battery ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Battery replacement •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 3 AC operation ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• DC12V supplied from Sumitomo fusion splicer •••••••••••••••••••••••••••••••••••••••••••• 5. Operating procedures ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 6. Temperature settings •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 7. Switching to HEATER MODE •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 8. Auto power off function ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 6 9.

  • Page 6: General

    DC cord *4 PC-B[C] Cleaning brush *1 *1 Sumitomo FHS series (for single fiber) or FHM series Hex driver (US) or (for ribbon fibers) fiber holders are needed to remove Allen key (UK) 1.5mm*1 fiber coating with the JR-6+.

  • Page 7: Structure

    For 6c fiber ribbon 1. Battery operation FHM-8 1pair For 8c fiber ribbon 2. AC operation FHM-10 1pair For 10c fiber ribbon 3. DC12V supplied from Sumitomo fusion FHM-12 1pair For 12c fiber ribbon splicer 3. Structure Battery operation Main body lid Keypad...

  • Page 8: Battery Replacement

    Warning and may cause battery leakage, heat generation, bursting and fire. Only JR-6+ ADC-1220S AC adapter (or Sumitomo Install the battery with a correct polarity. fusion splicer) to charge the battery. Caution Caution Failure to do may cause electric shock or fire.

  • Page 9: Operating Procedures

    ) for Good No good more than 1 second until the TEMP./BATT. indicator LEDs ( illuminate to indicate a current With use of Sumitomo fiber cleavers, battery remaining capacity. ensure that coating positioned in a specified yellow area. The HEATER LED ( ) turns green from red when the JR-6+ reaches the set temperature.

  • Page 10: Temperature Settings

    OME1826029B 10. Lightly brush the ends with your finger to fan Hold the “PUSH” portion firmly. out all fibers in a straight line (if cleaning ribbon fiber). Glass fiber is extremely sharp. Handle with care. Caution Slide the holder receptacle and 6.

  • Page 11: Auto Power Off Function

    Upper and lower blades are the same. than 5 minutes after the JR-6+ is powered off.) Please be sure to use a dedicated replacement blade "JR-6+BL". Using Clean the blades, heat plate and rubber pad with a the old type blade "JR-6BL" does not...
  • Page 12 OME1826029B 3. Fit a new upper blade to the JR-6+ and then tighten the setscrews temporarily. 4. Loosen the setscrews of the upper and lower blades so that the blades are a bit movable back and forth. A: There should not be a gap between the Ensure that the upper and lower lower blade and JR-6+ main body.

  • Page 13: Troubleshooting

    OME1826029B Troubleshooting 10. Battery storage If you are going to store the battery for more than Good 1 month, observe the followings. 1. Remove the battery from the JR-6+. No good (Refer to “4. Preparing power supply-Battery Fiber is broken. replacement”.) 2.
  • Page 14 OME1826029B...
  • Page 15 OME1826029B...
  • Page 16 SEI (PHILIPPINES) INCORPORATED North Carolina (U.S.A) Tel: +63 2 811 2755/2756 Sumitomo Electric Lightwave Corp. Singapore Sumitomo Electric Asia Pacific Pte. Ltd. 201 South Rogers Lane, Suite 100 Tel: +65 6261 3388 Raleigh, NC27610 U.S.A Toll Free No. 800 358 7378 http://www.seps.com.sg/...

Table of Contents