Related Manuals for MORTECH M677
Summary of Contents for MORTECH M677
- Page 1 Component Data M677 HAND CRANK CADAVER LIFT Mortech™ Manufacturing Inc. 411 North Aerojet Avenue, Azusa, CA 91702 (626) 334-1471 www.mortechmfg.com...
-
Page 2: Bloodborne Disease Notice
• Do the moving parts operate smoothly? Modifying the equipment can cause injury and damage. • Is unit draining properly? Use the equipment only as designed by Mortech. • Are plumbing features operating properly? • Are all nuts, bolts, and pins secured in place? If unit has an issue contact customer relations. - Page 3 M677 Hand Crank Lift Safety Information IMPORTANT Operate from the proper position. Keep your balance and Read and understand this instruction manual prior to proper footing at all times. IMPORTANT operating or performing maintenance on this lift! Read and understand this instruction manual prior to...
-
Page 4: Operating Procedure
M677 Hand Crank Lift Safety Information OPERATOR SAFETY INSTRUCTIONS (cont’d) OPERATING PROCEDURE Do not misuse the unit. Perform only the functions for which Remove the lift from the shipping pallet by cutting the bands the unit is designed. Never attempt to operate the equipment and rocking the lift back on the 10”... - Page 5 No riders are allowed WARNING ALL MOVING PARTS WHILE on this lift. This is not KEEP HANDS AWAY FROM OPERATING UNIT. ALL MOVING PARTS WHILE a personnel lift. OPERATING UNIT. M677 Hand Crank Lift Operation WARNING WARNING CAUTION FRONT NEVER ALLOW ANYONE WARNING Make sure the floor surface is level.
- Page 6 FRONT M677 Hand Crank Lift Operation LEFT RIGHT Position the lift on a level surface and pull the stabilizer legs down until the caster on each leg is snugly on the floor. Fold the leg until it forms a 90...
- Page 7 FRONT M677 Hand Crank Lift Operation Once the pins are locked in the holes, the carriage can be Operating Your Lift: rotated up into the travel/storage position. When operating the lift, the Mast Hold Down can be attached FRONT to the opposite side of the base upright and tucked behind...
- Page 8 M677 Hand Crank Lift Operation To release the brake, lay the lift back onto the winch wheels Reverse this step to reinsert the extensions. and place the tool into brake access slot located on the left side of the lift, and through the hole in the counterweight.
-
Page 9: Specifications
KEEP HANDS AWAY FROM No riders are allowed ALL MOVING PARTS WHILE ALL MOVING PARTS WHILE on this lift. This is not OPERATING UNIT. OPERATING UNIT. a personnel lift. M677 Hand Crank Lift Specifications WARNING WARNING WARNING WARNING WARNING Do not use Boom if plunger is not... - Page 10 M677 Hand Crank Lift Parts listing FRONT WARNING The center of gravity of the load should always be centered between the fork arms and as far back towards the lift as possible. LEFT RIGHT WARNING The center of gravity of the load should never extend past 22 in.
-
Page 11: Maintenance Instructions
M677 Hand Crank Lift Maintenance MAINTENANCE INSTRUCTIONS Before each use: 1. Inspect the cable for kinks and frays. If kinked or more than 3 wire strands are broken (small wires) do not use the lift until the cable has been replaced. -
Page 12: Troubleshooting
OPERATOR WARNING WARNING POSITION M677 Hand Crank Lift Troubleshooting KEEP HANDS AWAY FROM No riders are allowed ALL MOVING PARTS WHILE on this lift. This is not OPERATING UNIT. WARNING 7. Check stabilizer legs by lowering them into normal WARNING a personnel lift. - Page 13 M677 Hand Crank Lift Troubleshooting TROUBLESHOOTING PROBLEM CAUSE SOLUTION Load is easing down slowly The brake on the winch or ratchet dog are When load is in position, crank not installed correctly winch handles forward a half turn towards the lift to set the brake.
-
Page 14: Care Of Stainless Steel
M677 Hand Crank Lift Maintenance MAINTENANCE INSTRUCTIONS Shop Oil and Grease - These soils may be corrosive and may not allow the surface to maintain passivity, and so MAINTENANCE SCHEDULE removal is a necessity. Soap or detergent and water may be The unit requires regular maintenance and follow the used or a combination of detergent and water plus a solvent. -
Page 15: Maintenance Record
M677 Hand Crank Lift Maintenance record MAINTENANCE RECORD Date... -
Page 16: Training Record
M677 Hand Crank Lift Training record TRAINING RECORD Date... -
Page 17: Warranty
PROPRIETARY NOTICE © COPYRIGHT MORTECH MANUFACTURING INC., ALL The information in this manual is the property of Mortech RIGHTS RESERVED. Manufacturing. Mortech Manufacturing reserves all patent rights, proprietary design rights, manufacturing rights, reproductions rights, and sales use rights thereto, and to any...
Need help?
Do you have a question about the M677 and is the answer not in the manual?
Questions and answers